SF SF-540A Manuale utente
·
SF-540A
Laminator
Operating Manual
SF-540A 202205
1
Instructions of the operation manual：
★Before operating the laminating machine, please read and
understand the contents described in the manual carefully.
★Please keep this instruction manual for future reference.
★Please pay special attention to the sections marked with warning
symbols in the manual, which are very important for the correct use
and maintenance of the machine and the safety of users.
★With the improvement of product function and software upgrade,
the information of operation manual will be constantly changed and
perfected without further notice. The description and image
involved shall be subject to the actual contents in the packing box.
The company reserves the right to modify and interpret this
instruction manual. We strive to ensure the accuracy of the
instructions and the product functions and features described, but
we do not assume any responsibility for any differences between the
user manual and the product.
SF-540A 202205
2
Contents
1. Safety Precautions ............................................................................... 3
2. Application and characteristics of SF-540A ....................................... 4
3. Schematic diagram of the whole machine .......................................... 5
4. Operating instructions for operation panel ..........................................7
5. Main technical parameters .................................................................11
6. Operating cautions .............................................................................12
7. Assembly of machines .......................................................................13
8. Operating procedure and method of machine...................................18
9. How to use the slitter mechanism ..................................................... 37
10.Application method of upper point line cutter mechanism ............. 38
11. How to use aluminum foil mechanism ............................................39
12.Work to be done after operation ....................................................... 42
13.Film covering process guidance .......................................................43
14.Common problems in operation and solutions................................45
15.Technical service .............................................................................. 47
SF-540A 202205
3
1. Safety Precautions
1.1 Before operation of this machine, please note if the supply voltage
used matches the rated operating voltage of the machine. Use the supply voltage
consistent with the rated operating voltage of this machine. Never misuse the
supply voltage;
1.2 Please do not use damaged power cord or broken power socket;
1.3 The power supply should provide reliable grounding protection;
1.4 In order to avoid electric shock accident or machine failure, please do not
spray water or other liquids on the machine;
1.5 Please do not touch the surface of the steel roller with your hands to
avoid scalding skin;
1.6 Be aware not to entangle clothes, necktie, hair, necklace, cuffs and
the like into the running machine during the operation, which may cause
unnecessary damage to the machine;
1.7 In the process of film covering operation, please do not put any items other
than the coating on the working panel or the boxes on both sides, so as to avoid
accidental involvement of the articles and damage to the machine;
1.8 In case of fault, people other than professionals shall not attempt to
dismantle the machine for repair. Repair shall be conducted by professionals or
organized by local dealer. Dismantling and repair by unauthorized persons will
adversely affect the normal service and maintenance of the machine;
1.9 The environment for the operation of the unit shall range 10℃—40℃.
Ideal humidity: 55%. The unit should stay away from locations with high
SF-540A 202205
4
temperature (e.g. by air-conditioner), and damp and dusty locations;
1.10 When the machine is running, the operator should not leave his post;
1.11 Please prevent children from using or touching the machine;
1.12 When the machine is out of service for a long time, please cut off
the power supply;
1.13 Please do not change the original configuration of this machine. If the user
makes any changes, we will not take any responsibility for safety.
2. Application and characteristics of SF-540A
2.1 Application of SF-540A：
SF-540A fast laminator laminates printed matter, spray-drawing products,
packing boxes, books and the like, allowing them to resist water, stain and
damage, and providing durability. Featuring compact size, fast and continuous
lamination, automatic parting cut, easy operation, economics and utility, this
unit is ideal for the post production of various types of printed and packing
products.
2.2Performance characteristics
2.2.1Mirror chrome plating roller, oil heating;
2.2.2 Touch screen human-computer interaction display system;
2.2.3 Frequency control system;
2.2.4Electric hydraulic pressure system, film pressure adjustable;
2.2.5 Full automatic paper feeding control system, can overlap;
2.2.6Pneumatic automatic cutting system;
2.2.7Curling-preventing device, preventing laminated paper from curling;
2.2.8Film slitting device;
SF-540A 202205
5
2.2.9Air inflation shaft material roller device；
2.2.10Bronzing winding device；
2.2.11Upper point thread cutter device；
2.2.12Automatic stop function for paper shortage.
3. Schematic diagram of the whole machine
1.Feeder 2.Lifting paper feeding table 3.Foot switch 4. Upper left box
5.Operation display screen 6.Pressure regulating valve 7.Anti roll handle
8.Air expansion shaft and film winding shaft
9.Point line cutter mechanism 10.Slitter mechanism
11.Front guard 12.Vacuum pump switch
3
6
7
8
9
11
1
2
10
12
4
5
SF-540A 202205
6
13.Slitter support plate 14.Emergency stop switch 15.Castor wheel
16.Power switch 17.Power cord 18.Rear receiving tray
19.Right box 20. Tin foil winding mechanism
21. Laminating tension adjusting handle 22. Roll film damping device
19
13
15
16
17
18
20
21
14
22
SF-540A 202205
7
4. Operating instructions for operation panel
4.1 Main page
4.1.1Temperature setting display
temperature value of the laminating roller; the set value adjustment range is "80 ～
140 ℃", and if it is lower than 80 ℃, it will be displayed as "---"; when the button
"+" is pressed, the value of 80 will appear, and the machine will start to heat up.
Press "+" temperature setting value "+ 1" again, and press "+ 5" continuously; press
"- 1" for temperature setting value and "- 5" for a long time. When the machine
starts to heat up, the actual display temperature value changes with the actual
temperature of the laminating roller surface.
1. Temperature setting key 2. Speed setting area 3. Paper length setting key
4. Setting area of cutting value adjustment 5. Laminating roller lifting button
6. Lifting button of traction roller 7. Operation key 8. Stop key
9. Pedal forward button 10. Pedal reverse button 11. Foil 12. Set
5
6
7
8
10
11
3
1
9
12
4
2
SF-540A 202205
8
Note: (1) laminating can be carried out when the actual surface temperature of the
laminating roller reaches ± 5 ℃;
(2) when the heating function needs to be turned off, the set temperature
value should be reduced to 80 ℃ first, and then press the button "-" again.
When "-" appears, it means that the heating function of the machine has been
turned off;
(3) The temperature overshoot will appear in the initial heating, and the
overshoot is about 10 ℃and stable at the set value for about 15 minutes.
Please wait until the temperature value is stable, so as not to affect the film
quality.
4.1.2 Display of set speed value
The speed adjustment range of main roller is 1-20m / min, and the speed of each
gear is 0.5m/min, increasing or decreasing. Press the icon "+" to increase the speed
value, otherwise, press the icon "-" to decrease the speed value;
Note: the speed of slitting roller is not adjustable;
4.1.3 Paper length adjustment setting area
The adjustment range of paper length is 200-1200mm. Press the "+" or "-" button
to change the value by one digit, increase or decrease by 1 mm, and press for a long
time, and the value will increase or decrease in 20 units;
4.1.4 Setting area of cutting value adjustment
Press the "+" or "-" button to change the value by 1 bit, increase or decrease by 1
mm, and long press, the value will increase or decrease in 5 units;
4.1.5 Laminating roller lifting button
The icon is on, the icon is light, and the roller is closed. When the icon is under, the
roller is opened and the icon is dark ;
Note: when the laminating roller is not closed, the machine will not move after
SF-540A 202205
9
pressing the operation button
4.1.6 Lifting button of traction roller
The icon is at the top, the icon is light, the roller is closed, the icon is at the bottom,
the roller is open, and the icon is dark;
4.1.7 Run button
After pressing, the machine starts to work in linkage (i.e. both the cardboard baffle
and the cutting roller can act); when pressed, the icon is light in normal operation,
while it is dark in standby.
4.1.8 Stop button
This button controls the stop of the machine in the linkage state; after pressing the
button, the machine stops working, the icon is light , and the icon is dark during the
operation of the machine.
4.1.9 Pedal forward button
This button is used with the foot switch. Press this button to turn light. At this time,
the machine starts to run when you step on the foot switch (only the main motor
drives the rollers to run at the set speed). Release the foot switch and stop running.
The icon will be dark if you don't press the button. What is the speed setting value
of forward rotation, the actual machine will operate according to this set speed;
Note: (1) this button is usually used when the machine is preheated or debugged;
(2) if the foot switch is used, the cutting roller of the machine will not work;
(3) When the pedal forward rotation button is on, press the operation switch
to start the machine.
4.1.10 Pedal reverse button
This button is used with the foot switch. Press this button to turn light At this time,
the machine starts to run when the foot switch is stepped on (only the rollers driven
by the main motor run). After the foot switch is released, the icon will be dark;
Indice
