SFD CH-2001B STAND Guida rapida

These instructions are for your safety. Please read through them

thoroughly before use and retain for future reference.

Parts Supplied

Ref

Description

Illustration

Qty

Main body

Feet

Screw for feet

Tools Required (not supplied)

Cross Head Screwdriver

Before You Start

Check the pack and make sure you have all of the parts listed above.

This appliance is designed for use as a supplementary heat source, it is not

intended to be the main source of heat.

Assembly Instruction

Safety & Operating Instructions

CONVECTOR HEATER

CH-2001B STAND

Before using the heater, the feet (supplied separately in

the carton), must be fitted to the unit. These are to be

attached to the base of the heater using the 4 small self-

tapping screws provided, taking care to ensure that they

are located correctly in the bottom ends of the heater side

mouldings.

Operating Instructions

1. Place the product in an upright position on a flat, steady, stable, heat-resistant

surface. Make sure there is nothing flammable or heat sensitive within 1 metre (40

inches). Operating the product in any other position could cause a hazard.

2. Insert the plug into a suitable wall outlet after turning the thermostat switch

counter-clockwise to the minimum position and setting the Heater Switches and

Fan Switch to “OFF”. The heater is suitable for operation on an electricity supply

having the same voltage as that show on it’s rating label.

3. Turn on the Heater Switch to “I” (750W) for low heating. Turn on the Heater

Switch “II” (1250W) for medium heating. Turn on both switches for high heating

(2000W).

4. Turn the thermostat knob clockwise to maximum position. When the room

temperature has risen to a comfortable level, slowly turn thermostat counter-

clockwise until you hear a click. The thermostat will now attempt to maintain the

room at this temperature by automatically cycling on-and-off.

5. To adjust the room temperature, turn the thermostat clockwise to raise the

temperature, or counter-clockwise to lower it.

6. To turn the heater off, switch off both “750W” and “1250W” switches.

(Note: There may be trace of odour during the first few minutes of initial use. This is

normal and will quickly disappear. )

Safety Control

CAUTION: This product has two levels of overheat protection. Initial protection is

afforded by a re-settable overheat switch which, once the cause of the overheating

has been removed AND the heater has cooled down, will allow continued use. The

secondary protection is a thermal fuse which CANNOT be reset by the user.

In the event that the heater suffers an overheat –and shuts down –immediately

disconnect the power by switching the electricity OFF at the plug and remove the

plug from its socket. Remove any objects that may be causing the overheating, set

the power switch to “0” and turn the thermostat dial fully anticlockwise and leave the

heater to cool down fully.

Once completely cool switch the heater back on as above. If it fails to work it could

be that the secondary overheat protection device has operated –this overheat

protection system cannot be reset by the consumer. Do not open this product.

There are no user-serviceable parts inside.

Safety Warnings

1. Do not use the heater unless the feet are correctly attached.

2. WARNING : In order to avoid overheating, do not cover the heater.

3. Only connect the heater to a suitable wall socket outlet with a mains voltage as

specified on the rating plate.

4. Keep combustible material such as furniture, cushions, bedding, paper, clothes,

curtains etc. at least 1m away from the heater.

5. Do not use the heater in areas where flammable liquids are stored or where

flammable fumes may be present.

6. Always unplug the heater when not in use or when moving or cleaning it. Do not

pull the cord to unplug the heater.

7. Do not locate the heater below a socket-outlet.

8. Do not use this heater in the immediate surroundings of a bath, a shower or a

swimming pool.

9. Do not cover or obstruct any of the heat outlet grilles or the air intake openings of

the heater.

10. Do not use the heater in the rooms with explosive gas or while using inflammable

solvents, varnish or glue.

11. If the supply cord is damaged, it must be replaced by the manufacturer or its

service agent or a similarly qualified person in order to avoid a hazard.

12. Keep the heater clean. Do not allow any objects to enter any ventilation or

exhaust opening as this may cause electric shock, or fire or damage to the

heater.

13. Do not use heater outdoors.

14. This product is not a toy. It should not be used by children or infirm persons

without supervision.

15. Do not immerse cord, plug or any part of the appliance in water or any other

liquid.

16. Do not use the appliance for other than its intended use. This appliance is

intended for household use only.

17. Do not attempt to repair, disassemble or modify the appliance. There are no user-

serviceable parts inside.

18. Do not place the heater on carpets having a very deep pile.

19. Do not use the heater with a timer or programmer or any other device which

facilitates unattended switch-on.

20. The heater is hot when in use. To avoid burns and personal injury, do not let

bare skin touch hot surfaces. Use the carrying handles when moving the

product.

21. This appliance is not intended for use by persons (including children) with

reduced physical, sensory or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision or instruction concerning

use of the appliance by a person responsible for their safety.

22. Children should be supervised to ensure that they do not play with the appliance.

Plug Replacement

This appliance is supplied with a BS1363 3 pin plug fitted with a 13 Amp fuse.

Should the fuse require replacement, it must be replaced with a fuse rated at

13 Amp and approved to BS1362.

In the event the mains plug has to be removed/replaced for any reason,

please note:

The wires in the mains lead on this appliance are coloured in accordance with the

following code:

Green and Yellow –Earth

Blue –Neutral

Brown –Live

THIS APPLIANCE MUST BE EARTHED

As the colours may not correspond with the markings identifying the terminals in your

plug proceed as follows.

The green and yellow wire must be connected

to the terminal in the plug, which is marked with

the letter E or with the earth symbol or

coloured green and yellow.

The blue wire must be connected to the

terminal marked N or coloured black.

The brown wire must be connected to the

terminal marked L or coloured red.

Important - any cut off plug should be disposed of safely to prevent hazard. There is

a danger of electric shock if a cut off plug is inserted into a socket outlet.

Care and Cleaning

1. Always ensure the product’s housing is intact and completely assembled before

each use.

2. Clean the exterior surface of the product by wiping it with a soft, damp cloth.

CAUTION:Allow the product to completely cool before handling or cleaning it.

Ensure the product is in the “ 0 ” (OFF) position and the power cord is unplugged

from the electrical outlet before cleaning the product.

3. Do not allow water or other liquids to run into the interior of the product, as this

could create a fire and/or electrical hazard.

4. Do not use any abrasive cleaners or solvents, as product damage will occur.

5. Store the product in a clean, dry place when it is not in use.

Conformity with Directives

Conforms with relevant European Directives.

Environmental Protection

Waste electrical products should not be disposed of with household

waste. Please recycle where facilities exist. Check with your Local

Authority or retailer for recycling advice.

SFD Ltd BA22 8RT

Indice

Altri manuali SFD Stufa

SFD

SFD NDB-1C-20TS Guida rapida

Manuali Stufa popolari di altre marche

oventrop

oventrop Regucor Series Manuale utente

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuale utente

ELMEKO

ELMEKO ML 150 Manuale utente

BN Thermic

BN Thermic 830T Manuale utente

KING

KING K Series Guida

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guida rapida

Well Straler

Well Straler RC-16B Manuale utente

EUROM

EUROM 333299 Manuale utente

Heylo

Heylo K 170 Manuale utente

Eterna

Eterna TR70W Manuale utente

Clarke

Clarke GRH15 Manuale di istruzioni

IRSAP

IRSAP The Radiator Company Ovali Manuale utente

Empire Heating Systems

Empire Heating Systems WCC65 Manuale utente

Wetekom

Wetekom 92 86 43 Manuale utente

Desa

Desa SPC170-F Manuale utente

Watlow

Watlow Watrod Electric Tubular Heaters Manuale utente

Haverland

Haverland ECO-DRY GPS Series Manuale elenco delle parti

Stelpro

Stelpro ASILVC2060 Series Manuale utente