SGS SAT405 Manuale utente
FOR YOUR SAFETY
PLEASE READ THESE INSTRUCTIONS CAREFULLY
AND RETAIN THEM FOR FUTURE USE.
OWNER’S MANUAL
SAT405
CLIP HEAD NAILER
PAGE 2
SPECIFICATION
TOOL MODEL SAT405
MAXIMUM OPERATING PRESSURE 115 PSI
RECOMMENDED OPERATING PRESSURE 75-100 PSI
MAGAZINE CAPACITY 80 NAILS
FASTNER GAUGE 2.8-3.8 MM
FASTNER LENGTHS NAILS (MM) 50-90 MM
SAFETY GUIDELINES
Please read and fully understand the manual for information relating to protecting
YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS.
Indicates an immediately hazardous situation which if not
avoided will result in death or serious injury.
DANGER
WARNING
NOTE
Indicates a potentially hazardous situation which if not
avoided could result in death or serious injury.
Alerts the operator to useful information.
WARNING
The tool may bounce releasing the trigger and if uninten-
tionally allowed to re-contact the work surface with the
trigger still actuated (finger still pulling on the trigger) an
unwanted second fastener will be driven.
Contact Trip
WWW.SGS-ENGINEERING.COM
PAGE 3
SAFETY INSTRUCTIONS
1. Read and understand tool labels and manual. Failure to follow warnings
could result in DEATH or SERIOUS INJURY.
2. Operator and others in work area MUST wear safety glasses.
3. Keep fingers AWAY from trigger when not driving fasteners to avoid ac-
cidental firing.
4. Never point tool at any part of your body or others.
5. Never use oxygen or other bottled gasses. Explosion and serious per-
sonal injury could result.
6. Wear ear protection to safe-guard against possible hearing loss.
7. Use clean, dry, regulated, compressed air at 75 to 100 PSI.
8. Only use air hose that is rated for a maximum working pressure of at least
150 PSI or 150% of the maximum system pressure, which ever is greater.
9. Disconnect tool from air supply hose before performing tool mainte-
nance, clearing a jammed fastener, leaving work area, moving tool to another
location or handing the tool to another person.
10. Never use tool if safety, trigger or springs are inoperable, missing or
damaged. Do not alter or remove safety, trigger or springs. Make daily in-
spections for free movement of trigger and safety mechanism.
11. Connect tool to air supply before loading fasteners to prevent a fas-
tener from being fired during connection.
12. Operator and bystanders to wear helmets to safeguard against injuries.
13. Do not load fasteners with trigger or safety depressed to prevent
unintentional firing of a fastener.
14. Do not drive fasteners close to the edge of the work-piece. The work-
piece is likely to split allowing the fasteners to fly free or ricochet.
15. Fire fasteners into work-piece only - never into materials too hard to
penetrate. Do not drive fasteners on top of other fasteners, or with the tool
at too steep an angle; the fasteners can ricochet causing personal injury.
16. Always carry a fastener-driving tool using only the handgrip and never
with the trigger actuated. Never carry the tool by the hose or pull the hose to
move the tool.
PAGE 4
SAFETY MECHANISM
OPERATING A CONTACT TRIP SAFETY TOOL
The operator requires finger to be off the trigger and the work contact ele-
ment (WCE) of the tool to be placed on the work-piece.
The work contact element (WCE) is then depressed against the work-piece
and the trigger is pulled to drive a fastener.
The trigger is released after each fastener is driven.
Move the tool to next location and repeat the above procedure.
CHECKING A CONTACT TRIP SAFETY TOOL
Disconnect the air supply from the tool.
Empty the magazine.
Make sure the trigger and the safety move up and down without sticking.
Connect the air supply to the tool.
Depress the safety tip against the work-piece without pulling the trigger.
The tool must not cycle. Never use the tool if a cycle occurs.
Hold the tool clear of the work-piece. The WCE should return to its original
down position. Pull the trigger. The tool must not cycle. Never use the tool
if a cycle occurs.
WARNING
CHECK AND REPLACE ANY DAMAGED OR WORN COMPONENTS. SAFETY WARN-
ING LABELS ON THE TOOL MUST ALSO BE REPLACED IF THEY ARE NOT LEGIBLE.
WWW.SGS-ENGINEERING.COM
PAGE 5
LOADING THE TOOL
Connect the air hose.
Depress the magazine latch. Pull back on the magazine cover.
Insert a stick of fasteners into the magazine. Make sure the pointed ends of
the fasteners are loaded with the points downward. Also make sure fasten-
ers are not dirty or damaged.
Push the magazine cover forward until the latch catches.
OPERATING THE TOOL
Add a few drops of tool oil
Attach a high flow quick connector fitting to the tool. Empty the magazine.
Regulate the air pressure to obtain air pressure within the working pressure
range at the tool.
Load fasteners into your tool following the instructions in this manual.
Test for proper fastener penetration by driving nails into a sample piece of
wood. If the fasteners do not achieve the desired penetration, adjust the
air pressure to a higher setting until the desired penetration is achieved. If
you are using a tool with a depth control device, turn the thumb wheel to
achieve the desired penetration.
PAGE 6
LUBRICATING THE TOOL
Disconnect the air supply from the tool before lubricating.
Add a few drops of tool oil into the inlet.
Turn the tool so the inlet is facing up and put one drop of high speed spin-
dle oil into the air inlet. Never use detergent oil or additives. Operate the
tool briefly after adding oil.
Wipe off excessive oil at the exhaust. Excessive oil will damage O-rings in
the tool. If an in-line oiler is used manual lubrication through the air inlet is
not required on a daily basis.
Many air tool users find it convenient to use an oiler to help provide oil
circulation through the tool and increase the efficiency and useful life of the
tool. Check oil level in the oiler daily.
Many air tool users find it convenient to use a filter to remove liquid and
impurities which can rust or wear internal parts of the tool. A filter also
increase the efficiency and lifespan of the tool. The filter must be checked
on a daily basis and if necessary drained.
CORRECT CONNECTION OF THE TOOL
WWW.SGS-ENGINEERING.COM
PAGE 7
CLEARING A JAM FROM THE TOOL
1. Remove any remaining fasteners from the nailer.
A. Pull nail pusher all the way to the rear until it latches (Fig.1).
B. Slide fasteners to the rear and remove from magazine (Fig.2).
2. Use a pair of needle nose pliers and/or a flat screwdriver to free
bent fastener from back of nosepiece (see Fig.3). If fastener cannot
be removed it may be necessary to remove the magazine as follows:
A. Remove two screws (one on each side of tool) (A) Fig.4.
B. Remove two nuts (B) Fig.4.
C. Slide magazine back, off of nosepiece.
D. After clearing bent fastener reverse above to reassemble.
CLEANING THE TOOL
Disconnect tool before cleaning and inspection. Correct all
problems before placing the tool back in use.
NEVER USE PETROL OR OTHER FLAMMABLE LIQUIDS TO
CLEAN THE TOOL. VAPORS IN THE TOOL WILL IGNITE
AND CAUSE THE TOOL TO EXPLODE AND RESULT IN
DEATH OR SERIOUS PERSONAL INJURY.
Remove tar build up with kerosene #2 fuel oil or fuel.
Dry off tool completely before use.
DO NOT SOAK tool with cleaning solutions or damage may occur.
WARNING
DANGER
Fig.1
Fig.2
Fig.3
Fig.4
PAGE 8
PARTS DIAGRAM
WWW.SGS-ENGINEERING.COM
PAGE 9
PARTS LIST
PAGE 10
TROUBLESHOOTING
SERVICE AND REPAIRS
All quality tools will eventually require servicing or replacement of parts due to wear
from normal use. These operations should ONLY be performed by a licensed profes-
sional technician. Never try to repair the tool by yourself.
Disconnect tool from air supply before performing any
service procedure.
WARNING
SYMPTOM PROBLEM SOLUTION
Air leak near top
of tool or in trigger
area.
Loose screws.
Worn or damaged o-rings
or seals.
Tighten screws.
Install overhaul kit.
Tool does nothing
or operates
sluggishly.
Inadequate air supply.
Inadequate lubrication.
Worn or damaged O-rings
or seals.
Verify screws.
Install overhaul kit.
Air leak near
bottom of tool.
Loose screws.
Worn or damaged O-rings or
bumper.
Tighten screws.
Install overhaul kit.
Tool jams
frequently.
Incorrect fasteners.
Damaged fasteners.
Magazine or nose screw
loose.
Magazine is dirty.
Driver is worn or damaged.
Verify fasteners of correct size.
Replace fasteners.
Tighten screws.
Clean screws.
Install Driver maintenance kit.
Other Contact SGS Engineering.
WWW.SGS-ENGINEERING.COM
Indice
Altri manuali SGS Pistola sparachiodi
