Sharp B-32C1 Manuale utente
8M-B32C1 Dismantle Instruction
1
Dismantle Instruction
LCD MONITOR
MODEL
8M-B32C1
8M-B32C1 Dismantle Instruction
2
Table of contents
1. Scope.................................................................................................................. 3
2. Tools for dismantling............................................................................................... 3
3. Dismantle Procedure .............................................................................................. 3
4. Stand, Back cover and PWB Plate............................................................................... 4
5. Printed circuit boards ............................................................................................. 8
6. Battery................................................................................................................ 9
7. LCD Module ........................................................................................................ 10
8. Capacitors.......................................................................................................... 11
9. Parts List ........................................................................................................... 12
8M-B32C1 Dismantle Instruction
3
1. Scope
This document describes dismantling instruction according to Annex VII of Directive 2012/19/EU.
2. Tools for dismantling
Below tools are required to dismantle this product.
- Screw Driver
- Nipper
3. Dismantle Procedure
This product can be dismantled by below steps.
1. Remove Stand, Back cover and PWB Plate (section 4)
2. Remove Printed circuit boards (section 5)
3. Remove Battery (section 6)
4. Dismantle LCD (section 7)
5. Remove Electrolyte Capacitors (section 8)
8M-B32C1 Dismantle Instruction
4
4. Stand, Back cover and PWB Plate
Stand can be removed with screw driver.
Remove SCREW COVER SEAL on back cover.
Then back cover can be removed with screw driver.
8M-B32C1 Dismantle Instruction
5
Cut the cable tie on VESA angle with nipper, and peel off ALPET SHEET and ALPET SHEET S.
Then remove VESA angle with screw driver. (right side in back view)
ALPET SHEET S
ALPET SHEET
8M-B32C1 Dismantle Instruction
6
Detach the cables from DC switch PWB and remove the PWB with screw driver.
Remove WIRING SHEET (Black PC sheet) from PWB Plate.
Release all the cables that runs through the plate aperture. (cables from beneath the plate).
DC switch PWB
8M-B32C1 Dismantle Instruction
7
Detach Key-FFC from the connector on Main I/F PWB
Release from wire holders and remove the fixing tape on PWB Plate.
Then PWB Plate can be removed with screw driver.
(When the plate is lifted up, cables should go through the aperture of plate)
8M-B32C1 Dismantle Instruction
8
5. Printed circuit boards
All PWBs can be removed by screw driver.
Power PWB (1pcs)
Main I/F PWB (1pcs)
LED Driver PWB (2pcs) UCCT PWB (1pcs) DC switch PWB (1pcs)
Connector PWB (1pcs) Varistor PWB (1pcs)
T-CON PWB (1pcs) Key PWB (1pcs)
8M-B32C1 Dismantle Instruction
9
6. Battery
This model uses only CR2032 Lithium Coin battery on Main I/F PWB.
Battery CR2032 can easily be removed from the battery holder.
8M-B32C1 Dismantle Instruction
10
7. LCD Module
- LCD Dismantle procedure
LCD
Altri manuali per B-32C1
1
Indice
Altri manuali Sharp Monitor
Sharp
Sharp PN-T321 Manuale utente
Sharp
Sharp PN-L803C Manuale utente
Sharp
Sharp PN-CD701 Manuale utente
Sharp
Sharp LL-T17A4-H Manuale utente
Sharp
Sharp LL-T15A4 Manuale utente
Sharp
Sharp PN-L802B Manuale utente
Sharp
Sharp PN-HY501 Manuale utente
Sharp
Sharp PN -HW861 Manuale utente
Sharp
Sharp PN-E421 Manuale utente
Sharp
Sharp PN-V550A Manuale utente
Sharp
Sharp LL-H1813 Manuale utente
Sharp
Sharp PN-L805H Manuale utente
Sharp
Sharp LCD MONITOR Manuale utente
Sharp
Sharp PN-L803C Manuale utente
Sharp
Sharp LC-20VM2 Manuale utente
Sharp
Sharp PN-L601B Manuale utente
Sharp
Sharp PN-V600A Guida utente
Sharp
Sharp LL-T1815 Manuale utente
Sharp
Sharp LL-171MU Manuale utente
Sharp
Sharp PN-80SC5 Manuale utente
