Sharp PN -HW431T Manuale utente
PN-HW431T Dismantle Instruction
1
Dismantle Instruction
LCD MONITOR
MODEL
PN-HW431T
701
PN-HW431T Dismantle Instruction
2
Table of contents
1. Scope.................................................................................................................. 3
2. Tools for dismantling............................................................................................... 3
3. Dismantle Procedure .............................................................................................. 3
4. Back covers .......................................................................................................... 4
5. Printed circuit boards ............................................................................................. 5
6. Battery................................................................................................................ 5
7. LCD Module .......................................................................................................... 6
8. Capacitors............................................................................................................ 7
9. Parts List ............................................................................................................. 7
PN-HW431T Dismantle Instruction
3
1. Scope
This document describes dismantling instruction according to Annex VII of Directive 2012/19/EU.
2. Tools for dismantling
Below tools are required to dismantle this product.
- Screw Driver
- Nipper
3. Dismantle Procedure
This product can be dismantled by below steps.
1. Remove Back covers (section 4)
2. Remove Printed circuit boards (section 5)
3. Remove Battery (section 6)
4. Dismantle LCD (section 7)
5. Remove Electrolyte Capacitors (section 8)
PN-HW431T Dismantle Instruction
4
4. Back covers
Back cover can be removed by screw driver.
PN-HW431T Dismantle Instruction
5
5. Printed circuit boards
All PWBs can be removed by screw driver.
Main I/F PWB (1pcs) Power PWB (1pcs) LED driver PWB (1pcs)
T-CON PWB (1pcs)
6. Battery
This model uses only AAA battery for remote control.
Battery can easily be removed.
PN-HW431T Dismantle Instruction
6
7. LCD Module
- LCD Dismantle procedure
1. Remove the Brackets for touch panel mounting
2. Remove the Touch panel
3. Remove the Rear cover
4. Remove the PWBs
5. Remove the Cables
LCD
PN-HW431T Dismantle Instruction
7
8. Capacitors
Electrolyte Capacitors which diameter/height is larger than 25mm is installed on Power PWB.
These capacitors can be removed by using nipper to cut the leads.
On Power PWB
9. Parts List
Parts described in Annex VII of directive 2012/19/EU are as below.
Parts
Note
LCD
43inch LCD module
Printed Circuit Boards
Main I/F PWB
Power PWB
LED driver PWB
T-CON PWB
Battery
AAA battery
Electrolyte capacitors
(height >25mm, diameter >25mm)
On Power PWB
External electric cables
2 kinds of Power Cord
- for EU
- for UK
Indice
Altri manuali Sharp Monitor
Sharp
Sharp PN-L703A Guida utente
Sharp
Sharp PN-T322B Manuale utente
Sharp
Sharp PN-HM751 Guida utente
Sharp
Sharp PN-M401 Guida utente
Sharp
Sharp PN-HW431 Manuale utente
Sharp
Sharp PN-K321H Manuale utente
Sharp
Sharp PN-L601B Guida utente
Sharp
Sharp PN-S655 Manuale utente
Sharp
Sharp PN-R606 Manuale utente
Sharp
Sharp LL-T17A4-H Manuale utente
Sharp
Sharp PN-65SC1 Guida utente
Sharp
Sharp Smart Board Manuale di servizio
Sharp
Sharp PN-465E Manuale utente
Sharp
Sharp MultiSync ME652 Manuale utente
Sharp
Sharp PN-HW501 Manuale utente
Sharp
Sharp PN-425 Manuale utente
Sharp
Sharp PN-L601B Guida rapida
Sharp
Sharp PN-L803CA Manuale di installazione
Sharp
Sharp LC 20M4U Manuale utente
Sharp
Sharp PN-T321 Manuale utente
