Sharp PN-HW501 Manuale utente
PN-HW501 Dismantle Instruction
1
Dismantle Instruction
LCD MONITOR
MODEL
PN-HW501
701
PN-HW501 Dismantle Instruction
2
Table of contents
1. Scope.................................................................................................................. 3
2. Tools for dismantling............................................................................................... 3
3. Dismantle Procedure .............................................................................................. 3
4. Back covers .......................................................................................................... 4
5. Printed circuit boards ............................................................................................. 5
6. Battery................................................................................................................ 5
7. LCD Module .......................................................................................................... 6
8. Capacitors............................................................................................................ 7
9. Parts List ............................................................................................................. 7
PN-HW501 Dismantle Instruction
3
1. Scope
This document describes dismantling instruction according to Annex VII of Directive 2012/19/EU.
2. Tools for dismantling
Below tools are required to dismantle this product.
- Screw Driver
- Nipper
3. Dismantle Procedure
This product can be dismantled by below steps.
1. Remove Back covers (section 4)
2. Remove Printed circuit boards (section 5)
3. Remove Battery (section 6)
4. Dismantle LCD (section 7)
5. Remove Electrolyte Capacitors (section 8)
PN-HW501 Dismantle Instruction
4
4. Back covers
Back cover can be removed by screw driver.
PN-HW501 Dismantle Instruction
5
5. Printed circuit boards
All PWBs can be removed by screw driver.
Main I/F PWB (1pcs) Power PWB (1pcs) LED driver PWB (1pcs)
T-CON PWB (1pcs)
6. Battery
This model uses only AAA battery for remote control.
Battery can easily be removed.
PN-HW501 Dismantle Instruction
6
7. LCD Module
- LCD Dismantle procedure
1. Remove Rear cover
2. Remove PWBs
3. Remove the Cables
LCD
PN-HW501 Dismantle Instruction
7
8. Capacitors
Electrolyte Capacitors which diameter/height is larger than 25mm is installed on Power PWB.
These capacitors can be removed by using nipper to cut the leads.
On Power PWB
9. Parts List
Parts described in Annex VII of directive 2012/19/EU are as below.
Parts
Note
LCD
50inch LCD module
Printed Circuit Boards
Main I/F PWB
Power PWB
LED driver PWB
T-CON PWB
Battery
AAA battery
Electrolyte capacitors
(height >25mm, diameter >25mm)
On Power PWB
External electric cables
2 kinds of Power Cord
- for EU
- for UK
Indice
Altri manuali Sharp Monitor
Sharp
Sharp PN-B501 Guida utente
Sharp
Sharp PN-465U Manuale utente
Sharp
Sharp 8M-B70AU Manuale utente
Sharp
Sharp PN-E471 Manuale utente
Sharp
Sharp PN-V701 Foglio di istruzioni
Sharp
Sharp PN-E421 Manuale utente
Sharp
Sharp PN-60TA3 Manuale utente
Sharp
Sharp PN-L652B Manuale utente
Sharp
Sharp PN-HW431 Manuale utente
Sharp
Sharp PN-65SC1 Manuale utente
Sharp
Sharp PN-Y325 Guida utente
Sharp
Sharp PN-C603D Manuale utente
Sharp
Sharp PN-80TC3 Manuale utente
Sharp
Sharp PN -HW861 Manuale utente
Sharp
Sharp LL-T15V1 Manuale utente
Sharp
Sharp PN-70HC1E Guida utente
Sharp
Sharp PN-HW651 Guida utente
Sharp
Sharp PN-B401 Manuale utente
Sharp
Sharp PN-C705B Manuale utente
Sharp
Sharp PN-425 Manuale utente
