Sharp ES-HK800G Manuale utente
ES-HK800G
Operation Manual
WASHING MACHINE
If the appliance is sold or transferred to another owner or if you moved house and leaving the
appliance, always ensure the manual is supplied with the appliance in order for the new owner
can get to know its functions and its relevant warnings. These warnings have been provided for
your safety. You MUST read them carefully before installing or using the appliance.
Before using
Parts name........................................
1
Cautions........................................... 2
Installation and adjustment.................
4
How to usedrainpipe.......................... 5
Water
inlet
installation........................ 6
Operation
Preparation before operation..............7
Load
laundries..............................
..
..
8
Use
of detergent................................ 9
Control panel instructions..................
10
Operation steps................................ 12
Maintenance.....................................
16
Common non-fault phenomenon.........
17
Specification.....................................
20
Contents
Additionalfunctions.......................... 15
Others
.
3
Pay attention to the warning symbols.There may be serious risks on personal
safety or may damage the washing machine if not followed.
The contents of this symbol are prohibited.It may damage the appliance and
can lead to injury.
Prohibited symbol
Warning symbols
Drainpipe
The end connect to
the appliance
Bottom cover
(1pc) Water inlet hose (1pc) Outfall stopper
(1pcs)
The end connect to
water inlet hose connector
220V.
This appliance is not intended for use by persons(including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the
appliance by a person responsible for their safety.Children
should be supervised to ensure that they do not play with the
appliance.
Notice
Please install and adjust the machine according tothe requirements of the manual.
Correct operation is very important for your safety.
Unpacking
Unpack the carton and take out the bottom cover.
Open the top lid of washing machine and take out all of the accessories.
Remove all wrappers, including the polystyrene base.
You are advised to keep all the packaging for reuse in case the machine is to be
transported again.
Positioning
Make it horizontal.
Use a tied thread with plumb to check
if it is horizontal.
Adjust the adjustable foot
and twist the adjustable foot.
2) Fasten the nut after adjustment.
Installing the bottom cover
1°
Adjustable nut
Adjustable
foot
1) Lift up the adjustable foot gently, loose the adjustable nut
Fixing clamp
Scissors
Bottom cover
The base
The distance between the washing machine and the wall should be more than 50mm,
and the maximum allowable angle of the shank base of the machine is 1°.
The slanting or rough ground maycause operating stopped or unstable, please adjust it
with the following methods:
Let the back of washing machine incline forward,
make the side of the bottom cover with sticker
description facing outside. Insert it to the bottom
of washing machine along the direction of the
arrow.
Remove two fixing clamp by scissors, insert it on
on the cover's aloted holes as shown on the figure
(gently pull fixing clamp and it should not be pulled
out). Make the bottom cover fixed on the base.
1.The drainpipe must be hanged during use, the height is not more than 1.2m to
avoid leakage or stop, if drain a long time, the machine will stop running.
2.You can adjust the situation of the elbow bend pipe to change the height of the
drainpipe.
3.Do not extrude the drainpipe to ensue drain smoothly.
Drainpipe
Elbow
Less than 1.2m
Cautions:When install the washing machine, please use the new hose assy along with
the washing machine, old hose assy can not reuse.
Tap selection
Check the connection between inlet
hose connector and the tap
Connect the inlet hose with the washing machine
1. Swing the inlet hose gently to confirm if it is
fastened.
2. After installation,open the tap and check if
it leaks.
3. Do not bend the inlet hose with overstrain.
4. Before each usage,check the connection
between inlet hose connector and the tap.
Make sure they are firmly fitted to prevent
dropping from improper installation position.
1. Do not take off the water absorption cushion. Please
check if the cushion is dropped or damaged before
each usage. If it is, contact the seller immediately.
2. Put the inlet hose nut on the inlet valve connector.
3. Fasten the inlet hose nut and swing it gently to make
sure if it is suitable.
Inlet valve connector
Inlet hose nut
Water absorption cushion
Suitable tap
The front end should be longer than 10mm. The tap exit end
face should be flat and smooth, if not file it to avoid leakage.
Not suitable tap
8
Indice
Altri manuali Sharp Rondella
Sharp
Sharp ES-GFB8143WD-EE Manuale utente
Sharp
Sharp ES-HFB814AWA-FR Manuale utente
Sharp
Sharp ESX156 Manuale utente
Sharp
Sharp ES-NB814W-BE Manuale utente
Sharp
Sharp ES-NFA814BWB-CB Manuale utente
Sharp
Sharp ES-NFB914AWC-EN Manuale utente
Sharp
Sharp ES-HFA6123WD-EE Manuale utente
Sharp
Sharp ES-NFH014CWC-DE Manuale utente
Sharp
Sharp ES-HFA9143WD-EE Manuale utente
Sharp
Sharp ES-HFB812AWC-PL Manuale utente
Sharp
Sharp ES-HFA6123WD-FR Manuale utente
Sharp
Sharp ES-NFB612CWC-CZ Manuale utente
Sharp
Sharp ES-NFB014CWA-DE Manuale utente
Sharp
Sharp ES-HFA8123WD-EE Manuale utente
Sharp
Sharp ES-NFH714AWC-PL Manuale utente
Sharp
Sharp ES-NFB814CWA-DE Manuale utente
Sharp
Sharp ES-GFB7145WD-DE Manuale utente
Sharp
Sharp ES-HFH814AWC-FR Manuale utente
Sharp
Sharp ES-NFA8121WD-PL Manuale utente
Sharp
Sharp ES-NFA7121WD-PL Manuale utente
