Shure Microflex Manuale del proprietario

Interfacing Microflex Wireless to Polycom Devices

The Shure Microflex Wireless system can be easily connected to Polycom conferencing audio

processors. This guide will step the reader through the steps required to connect the MXW system to

various Polycom hardware.

Contents

What You’ll Need.................................................................................................................................2

Audio Cables....................................................................................................................................2

Input to Audio Processors....................................................................................................................3

SoundStructure C-Series ..................................................................................................................3

Vortex..............................................................................................................................................4

Audio Input for Video Processors.........................................................................................................5

HDX Series - 9000, 8000, 7000 .........................................................................................................5

RealPresence Series.........................................................................................................................5

What You’ll Need

Audio Cables

To connect the Shure Audio Network Interface (ANI) to Polycom devices, you will need block connector

audio cables.

Both the Shure and Polycom 3-pin block connector pinout are the same. The pin assignment is

described in the table below.

Pin 1

Pin 2

Pin 3

GND

For the reader’s convenience all of the Shure ANI audio connections are diagrammed below:

Finally, here is a useful diagram for how the 3-pin block connector can be wired to several other popular

connectors.

Input to Audio Processors

SoundStructure C-Series

C16, C12, C8, SR-12

Configure the Microflex Wireless (MXW) System

oDownload and Install the Shure Web Device Discovery Application found at

www.shure.com/software

oRun the Discovery Application on the same network as the MXW system

oDouble click the Access Point (APT), that you would like to configure

oSelect your desired APT, Charger and Audio Output Device from the drop down menus

on the Configuration Page of the APT GUI

oInsert microphones into the charger and press the “Link” button

oAudio will automatically be routed from the APT to the ANI Analog Outputs. By default

the ANI outputs are configured for Line level output, however they can be changed to

Aux (-10 dBV) or Mic (-30 dBV)

Using block connector audio cables, wire Outputs 1-8 of the ANI to Inputs 1-8 of the Polycom

SoundStructure as shown below.

Using Polycom SoundStructure Studio v1.9, create a new project for your design

On the Select Category pane, select Microphone

On the Select Input Type pane, select Wireless (Line or Mic Level depending on your ANI setting

as described above. Default is Line)

For Quantity, select the number of microphones you would like to use in the system

Label the microphones Shure Microflex Wireless or any other descriptor of your choice

Click the Add button beneath the Channels Defined pane

Click Next to move on to your audio Output stage definition and complete your design

Vortex

Configure the Microflex Wireless (MXW) System

oDownload and Install the Shure Web Device Discovery Application found at

www.shure.com/software

oRun the Discovery Application on the same network as the MXW system

oDouble click the Access Point (APT), that you would like to configure

oSelect your desired APT, Charger and Audio Output Device from the drop down menus

on the Configuration Page of the APT GUI

oInsert microphones into the charger and press the “Link” button

oAudio will automatically be routed from the APT to the ANI Analog Outputs. By default

the ANI outputs are configured for Line level output, however they can be changed to

Aux (-10 dBV) or Mic (-30 dBV)

Using block connector audio cables, wire Outputs 1-8 of the ANI to Inputs 1-8 of the Polycom

Vortex as shown below.

Using Polycom Conference Composer v3.0.1, create a new project for your design using the

InstantDesigner

On the Select Input Type pane, select Microphone

Select Wireless (Line or Mic Level depending on your ANI setting as described above. Default is

Line)

For Quantity, select the number of microphones you would like to use in the system

Label the microphones Shure Microflex Wireless or any other descriptor of your choice

Click the Add Input button

Click Next to move on to your audio Output stage definition and complete your design

Audio Input for Video Processors

HDX Series - 9000, 8000, 7000

The HDX series only allows one analog input to be used as a microphone input. You have a few options

for audio use with the HDX:

A. Only use one microphone for input

B. Route the MXW APT to a Shure SCM820 with Intellimix to automix the 8 microphones into a

single output

C. Use a Polycom SoundStructure C-Series mixer with a digital microphone connector to send

audio to the HDX system

D. Use a 3rd party mixer to mix multiple MXW microphones into a single output

Option B - Setup using a Shure SCM820

Configure the Microflex Wireless (MXW) System

oDownload and Install the Shure Web Device Discovery Application found at

www.shure.com/software

oRun the Discovery Application on the same network as the MXW system

oDouble click the Access Point (APT), that you would like to configure

oSelect your desired APT, Charger and Audio Output Device from the drop down menus

on the Configuration Page of the APT GUI

oInsert microphones into the charger and press the “Link” button

oAudio will automatically be routed from the APT to the SCM820 Digital Inputs

oReturn to the Discovery Application and open the GUI of the SCM820

oSelect the Output Tab and ensure the Mix Output A Gain Slider is appropriately set

Using block connector audio cables, wire the Mix A Output of the SCM820 to Input 1 of the

Polycom HDX

9000 Specific Instructions

To configure a Polycom HDX 9004, 9002 or 9001 system to use devices directly to audio input 1:

Do one of the following:

oIn the local interface go to System -> Admin Settings -> Audio -> Inputs/Outputs

oIn the web interface, go to Admin Settings -> Audio

Do the following:

oSet Input Type to Microphone

oEnable Echo Cancellor

oAdjust the audio Input Type Level if necessary

oSpeak into the microphones that are connected to the audio inputs. The audio meter

should peak at about 5 dB for normal speech

RealPresence Series

Unfortunately, the RealPresence series uses a proprietary audio connector and cable. This product is

not directly compatible with the Shure Microflex Wireless system. To use the Microflex Wireless system

with a RealPresence Series system, you must first connect Microflex Wireless to a SoundStructure C-

Series processor as described above and then send audio over the digital microphone connector to the

RealPresence.

Altri manuali per Microflex

Indice

Altri manuali Shure Sistema di conferenza

Shure

Shure DDS 5900 Manuale utente

Shure

Shure DM 6680 P Manuale utente

Shure

Shure CU 6105 Manuale utente

Shure

Shure DC 6120 P Manuale utente

Shure

Shure DCS 6000 Manuale utente

Shure

Shure MX890 Manuale utente

Shure

Shure STEM HUB Manuale utente

Shure

Shure MXA902 Manuale utente

Shure

Shure MICROFLEX SERIES Manuale utente

Shure

Shure IS 6132 Manuale utente

Shure

Shure Microflex Complete MXC Series Manuale utente

Shure

Shure DT 6008 Manuale utente

Shure

Shure DCS 6000 Manuale utente

Shure

Shure CM 6680 F Manuale utente

Shure

Shure INTELLIMIX P300 Manuale utente

Shure

Shure MXCW Scheda tecnica

Shure

Shure SZ 6104 Manuale utente

Shure

Shure DDS 5900 Manuale utente

Shure

Shure DDS 5900 Manuale utente

Shure

Shure INTELLIMIX P300 Istruzioni originali

Shure

Shure Microflex Complete Wireless MXCW Manuale utente

Shure

Shure RP 6004 Manuale utente

Shure

Shure DCS 6000 Manuale utente

Shure

Shure MXW6W Manuale utente

Manuali Sistema di conferenza popolari di altre marche

Kramer

Kramer VIA GO Manuale utente

AVT

AVT MAGIC AC1 Go Manuale utente

ProSoft Technology

ProSoft Technology AN-X4-AB-DHRIO Manuale utente

Sony

Sony PCS-I150 Manuale utente

Middle Atlantic Products

Middle Atlantic Products VTC Series Manuale utente

Prentke Romich Company

Prentke Romich Company Vanguard Plus Guida

Speakerbus

Speakerbus iD 712 Manuale utente

Trelleborg

Trelleborg SafePilot CAT PRO Manuale utente

Sennheiser

Sennheiser ADN Manuale utente

ADTRAN

ADTRAN NetVanta 7100 Manuale utente

AINA

AINA PTT Voice Responder Manuale utente

Yamaha

Yamaha ProjectPhone PJP-100H Manuale utente

vissonic

vissonic VLI Series Manuale utente

Panasonic

Panasonic KX-VC500 Manuale utente

Poly

Poly Trio 8300 Manuale utente

Crestron

Crestron Mercury CCS-UCA-SMK Disegno dimensionale

Inmarsat

Inmarsat mini M Manuale utente

Tenveo

Tenveo ALL-IN-ONE Manuale utente