Shure SBC250 Manuale utente

1/12

SBC250

2-Up Networked Docking Station

IMPORTANT SAFETY INSTRUCTIONS

1. READ these instructions.

2. KEEP these instructions.

3. HEED all warnings.

4. FOLLOW all instructions.

5. DO NOT use this apparatus near water.

6. CLEAN ONLY with dry cloth.

7. DO NOT block any ventilation openings. Allow sufficient distances for adequate ventilation and install in accor

dance with the manufacturer’s instructions.

8. DO NOT install near any heat sources such as open flames, radiators, heat registers, stoves, or other appara

tus (including amplifiers) that produce heat. Do not place any open flame sources on the product.

9. DO NOT defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wider

blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an

electrician for replacement of the obsolete outlet.

10. PROTECT the power cord from being walked on or pinched, particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

11. ONLY USE attachments/accessories specified by the manufacturer.

12. USE only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.

When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. UNPLUG this apparatus during lightning storms or when unused for long periods of time.

14. REFER all servicing to qualified service personnel. Servicing is required when the apparatus has been dam

aged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen

into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has

been dropped.

15. DO NOT expose the apparatus to dripping and splashing. DO NOT put objects filled with liquids, such as vas

es, on the apparatus.

16. The MAINS plug or an appliance coupler shall remain readily operable.

17. The airborne noise of the Apparatus does not exceed 70dB (A).

18. Apparatus with CLASS I construction shall be connected to a MAINS socket outlet with a protective earthing

connection.

Shure Incorporated

2/12

19. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

20. Do not attempt to modify this product. Doing so could result in personal injury and/or product failure.

21. Operate this product within its specified operating temperature range.

Explanation of Symbols

Caution: risk of electric shock

Caution: risk of danger (See note.)

Direct current

Alternating current

On (Supply)

Equipment protected throughout by DOUBLE INSULATION or REINFORCED INSULATION

Stand-by

Equipment should not be disposed of in the normal waste stream

WARNING: Voltages in this equipment are hazardous to life. No user-serviceable parts inside. Refer all servicing

to qualified service personnel. The safety certifications do not apply when the operating voltage is changed from

the factory setting.

General Description

SBC250 networked docking station provides simple charging, configuration, and storage for either 2 ULXD6 and

ULXD8 transmitters. Dock transmitters for 15 minutes to get 1 hour of use, or charge for 3 hours for a full charge.

Connect to a network to adjust transmitter settings and monitor rechargeable battery information. Use Shure con

trol software such as Wireless Workbench or other external control systems such as AMX or Crestron to monitor

and make changes.

Features

•Compatible with ULXD6 and ULXD8 transmitters using Shure rechargeable batteries

•Connect up to 2 transmitters for 15 minutes to get 1 hour of use, or 3 hours for a full charge

• Easily adjust transmitter settings using Shure control software such as Wireless Workbench and external con

trol systems such as AMX or Crestron

•Monitor rechargeable battery information such as health, temperature, charge, and cycle using control software

•Update transmitter and docking station firmware using Shure Update Utility

Shure Incorporated

3/12

•Rack- or wall-mountable with Shure URT3 mounting tray (sold separately)

Rack and Wall Mounting

SBC250 can be rack- or wall-mounted using the optional Shure URT3 universal rack tray for added flexibility when

storing ULXD6 boundary microphones.

①When mounting to a rack, position the rotatable ears on the URT3 with the

holes facing forward

②For mounting to a wall, rotate the ears so the holes are flush with the surface

Caution: When mounted on the wall, insert and remove ULXD6 boundary microphones vertically to avoid damag

ing the USB connector

More Information Available Online

A comprehensive online user guide is available at pubs.shure.com (http://pubs.shure.com).

Shure Incorporated

4/12

Controls and Connectors

①Power Switch

Powers the unit on or off.

②AC Power

IEC connector 100 - 240 V AC.

③Power LED

•On = Docking station is on

•Off = Docking station is off

④Ethernet Port

Connect to an Ethernet network to enable remote device control and monitoring using Wireless Workbench or oth

er control software.

⑤Ethernet Link Speed LED (Amber)

•Off = 10 Mbps

•On = 100 Mbps

⑥Ethernet Status LED (Green)

•Off = No network link

•On = Network link established

•Flashing = Network link active

⑦Charging Slots (USB 3.0)

Slide any ULXD6 or ULXD8 transmitter with Shure rechargeable batteries into slots to begin charging.

Shure Incorporated

5/12

⑧Charging Status LEDs

Each charging slot has five LEDs that illuminate to show the battery's charge level:

LED % Battery Charge

1•Flashing: <10%

•Solid: >10%

2 >25%

3 >50%

4 >75%

5 100%

⑨Reset Button

• Docking station reset: Press and hold reset button while simultaneously powering on the docking station to re

store factory settings. IP addressing will be reset to Automatic. Charging LEDs = solid green.

•Transmitter reset: Place transmitters in charging docks. Press and hold reset button for five seconds to restore

transmitter factory settings. Transmitter mute LEDs = flashing.

⑩ID Button

Identifies devices shown in Wireless Workbench by causing both the device's LED and the corresponding icon in

WWB to flash.

Power Connections

1. Connect power supply to a power outlet and to the docking station power input.

2. The docking station turns on and off via toggle switch.

If the docking station loses power, transmitters will also power off.

Connecting Transmitters

Insert a ULXD6 or ULXD8 transmitter with Shure rechargeable batteries into the slot as shown:

Shure Incorporated

6/12

The docking station provides power to charge transmitter batteries:

•15 minutes = 1 hour of use

•1 hour = 50% charged

•3 hours = 100% charged

Note: If the docking station loses power, transmitters will also power off. Batteries will resume charging when pow

er is restored.

Connecting Shure Devices to Wireless Workbench

Wireless Workbench lets you control and monitor devices over the network. To get started, visit http://

www.shure.com/wwb (http://www.shure.com/wwb) and download Wireless Workbench software. Wireless Work

bench communicates with connected devices over a standard Ethernet network.

Required equipment: Shure device, computer with Wireless Workbench installed, Cat 5 (or better) Ethernet ca

ble, and router or network switch

1. Connect the device to your computer with a shielded Cat 5 (or better) Ethernet cable to ensure reliable network

performance. If you have multiple devices to manage, connect each device to a router or network switch. The

Ethernet port LEDs on your device will illuminate to indicate network connectivity. Verify that Shure devices can

see each other by looking for the network connectivity icon on the front panel (location varies).

2. For most applications, use the Automatic mode (default) to let your switch or router assign an IP address using

DHCP addressing. If no DHCP server is present, your devices will fall back to a link-local address in the

169.254.xxx.xxx range. If you need to assign specific IP addresses, set the IP mode to Manual in the Network

menu. Find model-specific instructions at http://shure-community.custhelp.com/posts/a21b97f121 (http://shure-

community.custhelp.com/posts/a21b97f121).

3. Open Wireless Workbench software.

4. Select a Network Interface in the pop-up window. Choose the network that most closely matches the Ethernet

port where your devices are connected.

5. Your device will appear in the Inventory tab when the connection is successful.

Shure Incorporated

7/12

Configuration Tips

•Check your firewall settings to make sure Wireless Workbench has access to your network

•Use multiple Ethernet switches to extend the network for larger installations

For more help, visit the Help menu in Wireless Workbench or http://www.shure.com/wwb (http://www.shure.com/

wwb).

Monitoring Batteries with Wireless Workbench

Wireless Workbench provides detailed battery information for each transmitter.

Click the Inventory tab to view the networked docking station in Wireless Workbench.

Each tab provides different battery statistics:

Charge

Displays charge as a percentage of the total battery capacity. Also shows time remaining to full charge.

Health

Displays health of selected battery as a percentage of the charge capacity of a new battery. Charge capacity (bat

tery life when fully charged) will decline as a result of repeated charge cycles, age, or storage conditions.

Cycle

Displays total number of times that the battery has undergone one full count of discharge and charge. Recharging

after discharging halfway counts as one half of a cycle. Recharging after discharging a quarter of the way counts

as one quarter of a cycle.

Temperature

Displays battery temperature (in Celsius and Fahrenheit) and status.

Tip: To identify individual transmitters on the SBC250, press and hold the mute button on your ULXD6 or ULXD8

to make the corresponding icon in WWB flash. Clicking Dismiss all clears the flashing.

Shure Incorporated

8/12

Controlling Transmitters with Networked Docking Stations

Quickly review and control many transmitter settings using Wireless Workbench or other external control systems.

You can adjust the following settings:

•Mute button and mute LED behavior or brightness

•High-pass filter

•RF power

•Power lock

•Initial state from charger

•Battery type

•Device name

•Channel name

•Frequency

•Normal or High-Density Mode

•Boundary and gooseneck offset

1. Place transmitters on the docking station. Check that the docking station is connected to the network and to

Wireless Workbench.

2. Find the docking station in the inventory and right-click to select Properties.

3. Select one or multiple transmitters.

4. Make changes to transmitter settings and select Apply. Transmitters are now ready to use.

Connecting to an External Control System

SBC250 networked docking stations connect to external control systems such as AMX or Crestron via the Ether

net. Use only one controller per system to avoid messaging conflicts. For a comprehensive list of command

strings, visit http://www.shure.com (http://www.shure.com).

•Connection: Ethernet (TCP/IP; SBC250 is the client)

•Port: 2202

Shure Incorporated

9/12

Firmware Updates

Firmware is embedded software in each component that controls functionality. Periodically, new versions of

firmware are developed to incorporate additional features and enhancements. To take advantage of design im

provements, download new versions of the firmware using the Shure Update Utility tool.

Download Shure Update Utility at http://www.shure.com/suu (http://www.shure.com/suu).

Updating Transmitter Firmware with Docking Station

1. Place transmitters on the docking station and check that docking station is connected to the network.

2. Launch Shure Update Utility to find firmware updates.

3. Download updates and click Send Updates.

Model Variations

All include power supply unless otherwise noted.

Region Model

United States SBC250-US

Argentina SBC250-AR

Brazil SBC250-BR

Europe SBC250-E

United Kingdom SBC250-UK

Japan SBC250-J

China SBC250-CN

Korea SBC250-K

Taiwan SBC250-TW

Australia SBC250-AZ

India SBC250-IN

Global SBC250 (no power supply)

Shure Incorporated

10/12

Specifications

SBC250

Charge Time

ULXD6 and ULXD8 15 minutes = 1 hour runtime; 1 hour = 50% charged; 3 hours = 100% charged

Network Interface

10/100 Mbps Ethernet

Power Requirement

100 - 240V AC @ 0.35 A maximum, 50/60 Hz

Housing

Molded Plastic, Sheet Metal

Dimensions

215 x 191 x 62.5 mm (8.46 x 7.52 x 2.44in.)

Weight

2.7 kg(5.95 lb)

Operating Temperature Range

0°C (32°F) to 45°C (113°F)

Storage Temperature Range

-29°C (-20°F) to 74°C (165°F)

Certifications

Meets essential requirements of all applicable European Directives.

The CE Declaration of Conformity can be obtained from: www.shure.com/europe/compliance

Authorized European representative:

Shure Europe GmbH

Headquarters Europe, Middle East & Africa

Department: EMEA Approval

Jakob-Dieffenbacher-Str. 12

75031 Eppingen, Germany

Phone: +49-7262-92 49 0

Indice

Altri manuali Shure Stazione di attracco

Shure

Shure SBC450 Manuale utente

Manuali Stazione di attracco popolari di altre marche

Sony

Sony Dream Machine XDR-DS12iP Manuale utente

Acer

Acer USB Type-C Dock II Manuale utente

ATEN

ATEN UC-2000 Manuale utente

Xcellon

Xcellon HDD-202 Manuale utente

Dok

Dok CR09 Manuale utente

Philips

Philips BTM630/12 Manuale utente

IOGear

IOGear Travel Pro GUD3C09 Manuale utente

RKI

RKI SDM-E2 Manuale utente

iHome

iHome iP15 Manuale utente

VITURE ONE

VITURE ONE MOBILE DOCK Manuale utente

Lindy

Lindy 42984 Manuale utente

CipherLab

CipherLab 8001 Manuale utente

Pyle

Pyle PIPDSP2 Manuale utente

Avol

Avol AS2350 Manuale utente

Datalogic

Datalogic JoyaTouch Manuale utente

Philips

Philips DC190/79 Manuale utente

Targus

Targus DOCK315EUZ Manuale utente

Akasa

Akasa DuoDockX3 AK-DK08U3-BK Manuale utente