Shure PGX Wireless System Scheda tecnica

1/21

PGX -- Shure PGX Wireless

Quick Setup

Shure Incorporated

2/21

Shure Incorporated

3/21

Shure Incorporated

4/21

System Components

All systems include:

•PGX4 receiver

•2 AA batteries

•PS24 Power Supply

•User guide

Lavalier, Headworn, and Instrument systems include:

•PGX1 bodypack transmitter

• Microphone (choice of WL93, WL185, PG30 or Beta 98H/C™)

Vocalist systems include:

•Microphone Head (choice of PG58, SM58 , SM86, Beta 58A )

•PGX2 handheld transmitter

•Microphone clip

Guitar systems include:

•PGX1 bodypack transmitter

• 1/4” to mini 4-pin guitar cable

PGX4 Receiver Features

Front Panel

①audio LED

Indicates strength of incoming audio signal: green for normal, amber for strong and red for clipping.

②LED Screen

Displays group and channel setting. See “Single System Setup” for details.

③channel button

Changes group and channel setting. See “Single System Setup” for details.

④ready LED

Indicates system ready and receiving an RF signal from the transmitter.

® ®

Shure Incorporated

5/21

⑤Infrared (IR) port

Sends IR signal to transmitter for sync.

⑥sync button

Press to synchronize transmitter with receiver group and channel settings.

Back Panel

⑦AC adapter jack

⑧Adapter cord tie-off

⑨XLR microphone output jack

⑩ 6.35 mm (1/4”) instrument level output jack (unbalanced).

Transmitter Controls and Connectors

①Indicator LED Displays battery level, mute, and IR transmission status (see table).

②Power / Mute Switch Press to mute or unmute. Press and hold to power on or off.

③Infrared (IR) port Receives infrared beam to synchronize frequencies. When using

multiple systems, only one transmitter IR port should be exposed at a time.

Shure Incorporated

6/21

④4-Pin Microphone Input Jack.

⑤Audio Gain Adjustment.

Transmitter Indicator LED

Green Ready

Flashing green Controls Locked

Amber Mute On

Flashing red IR transmission in process

Glowing red Battery power low

Pulsing Red on startup Batteries dead (transmitter cannot be turned on until

batteries are changed)

Pulsing Red after synchronization Transmitter and receive incompatible; contact your

Shure reseller

Changing Batteries

•Expected life for an Alkaline battery is approximately 8 hours.

•When the transmitter light glows red, the batteries should be changed immediately, as shown.

Wearing the Bodypack Transmitter

Clip the transmitter to a belt or slide a guitar strap through the transmitter clip as shown.

For best results, slide the transmitter until the belt is pressed against the base of the clip.

Shure Incorporated

7/21

Adjusting Gain

PGX1

Three gain settings are available on the PGX1. Choose the appropriate setting for your instrument.

•mic: Microphone (higher amplification)

•0: Guitar with passive pickups (medium amplification)

• –10: Guitar with active pickups (lower amplification)

If the receiver LED indicates the input volume is overloading the receiver, try switching the gain to a lower setting.

PGX2

Shure Incorporated

8/21

Access the gain adjustment switch by unscrewing the head of the microphone.

Two gain settings are available on the PGX2. Use the tip of a pen or a small screwdriver to move the switch.

•0dB: For quiet to normal vocal performance.

• –10dB: Use only if audio is distorted due to high voal levels.

Single System Setup

1 Scan

Use the scan feature on the receiver to find a clear channel.

aLED screen displays current channel

bpress channel button to scan for a clear channel

csystem scans for the channel with the least interference

2 Synchronize

Synchronize the transmitter to the receiver by aligning the infrared (IR) ports and pressing the sync button. Make

sure the IR ports are closely aligned.

After a successful sync, the transmitter LED momentarily flashes red and the receiver ready light illuminates.

Shure Incorporated

9/21

Multiple System Setup

Use the following steps to ensure the best performance when installing multiple wireless systems at the same lo-

cation.

1. Turn all receivers on and all transmitters off.

Note: Turn on any other digital equipment that could cause interference during the performance so it will be de-

tected during the frequency scans in the following steps.

2. Make sure the group number is the same for all receivers (see Manual Group Selection).

3. Perform a scan using the first receiver.

4. Turn on the first transmitter and sync it to the receiver.

5. Repeat for each system.

◦Important: After syncing each transmitter, leave it on so that scans from the other receivers will not select

that channel.

◦Be sure only one transmitter IR port is exposed when synchronizing each system.

Manual Channel and Group Selection (receiver only)

Using the receiver to scan for a channel is the best way to find the best frequency for your system. However, for

multiple system setup, you may need to manually set the group number.

1. Press and hold the channel button.

2. Hold the button until the channel or group display begins flashing.

3. Release and press the button again to advance the setting. At the desired channel or group number, wait for

the flashing to stop. This activates the new setting.

4. Transfer the new frequency setting to the transmitter using the automatic sync function.

Shure Incorporated

10/21

Locking and Unlocking Controls

Locking the system controls prevents accidental muting or channel adjustment during performances.

Transmitter

To lock the controls: With the transmitter off, hold the power button down until the green LED flashes (~5 seconds)

To unlock the controls: With the transmitter on, hold the power button down until the green LED flashes (~5 sec-

onds)

Receiver

To lock the channel: Hold the channel button until the numbers flash (~10 seconds)

To unlock the channel: Hold the channel button until the numbers flash (~5 seconds)

Troubleshooting

Issue Indicator Status Solution

No sound or faint

sound

Transmitter power

light on, receiver

LEDs on

• Perform automat-

ic transmitter set-

•Verify all sound

system connec-

tions

Altri manuali per PGX Wireless System

Indice

Altri manuali Shure Sistema microfonico

Shure

Shure W10BT Manuale utente

Shure

Shure QLX-D Manuale utente

Shure

Shure ULX Wireless System Manuale del proprietario

Shure

Shure P10TR Manuale utente

Shure

Shure ULX Wireless System Manuale utente

Shure

Shure QLX-D Manuale utente

Shure

Shure ULX-D Manuale di programmazione

Shure

Shure LX Wireless System Manuale utente

Shure

Shure The SM58 Vocal Artist UHF Manuale utente

Shure

Shure MXWAPT Series Scheda tecnica

Shure

Shure Unf-R Manuale utente

Shure

Shure BLX Series Manuale utente

Shure

Shure SLX-D Manuale utente

Shure

Shure AMS4000 Guida utente

Shure

Shure THE TWIN PRO 27C8642 Manuale utente

Shure

Shure ULXD14 Manuale utente

Shure

Shure microphone system Manuale utente

Shure

Shure EXHIBIT 212 Manuale utente

Shure

Shure ULX Wireless System Manuale del proprietario

Shure

Shure SVX Wireless Manuale utente

Shure

Shure MX890 Manuale utente

Shure

Shure MXW Series Manuale utente

Shure

Shure LEGENDARY PERFORMANCE ULX-D Manuale utente

Shure

Shure BLX14E T11 Manuale utente

Manuali Sistema microfonico popolari di altre marche

Paso

Paso R824 Manuale utente

Naxa

Naxa NAM-982 Manuale utente

Motorola

Motorola PMNN4461 Manuale utente

Xvive

Xvive U3 Manuale utente

Tekon

Tekon DUOS Manuale utente

Heyuan Intelligence

Heyuan Intelligence IOT-G2S-01 Manuale utente

Devine

Devine WMD-IE Manuale utente

LG LF-D7150 Manuale utente

GE S768DAV Manuale utente

LD U305 HBH 2 Manuale utente

Chainway

Chainway URA8 Manuale utente

ORATOR

ORATOR D860TD Manuale utente

Sennheiser

Sennheiser Evolution Wireless Digital EW-DX EM 2 Manuale utente

Alpha Technologies

Alpha Technologies RBMS Manuale utente

SWIT Electronics Co.,LTD.

SWIT Electronics Co.,LTD. CW-S150 Manuale utente

Panasonic

Panasonic SHFX70 - DVD HOME THEATER WIRELESS SYSTEM Manuale utente

Pyle

Pyle PDWM5000 Manuale utente

Airspan

Airspan AS4000 Guida