Shure A310-FM Manuale utente

1/9

A310-FM -- Installation Guide

Permanent Table Installation

The tube and wing nut required to install the rack tray are included with the MXA310 microphone. Refer to the

MXA310 user guide for replacement part information.

Tip: This process assumes that both ends of the network cable are accessible. If the other end of the network ca

ble is not accessible, before installing the tube and plugging in the microphone (step 2), you must guide the cable

through the hardware components in the following order:

1. Wing nut (see image for correct orientation)

2. Bracket (under table)

3. Table

4. Tray (above table)

Shure Incorporated

2/9

Installation Process

1. Remove the 3 screws located in the center on the bottom of the microphone

Shure Incorporated

3/9

2. Plug a network cable into the microphone and guide it through the center exit path. When the cable is secured,

guide it through the tube.

Note: If necessary, remove the retaining tabs to install thicker cable. Replace them after the cable is installed.

Shure Incorporated

4/9

3. Align the tube into the recessed area in the center of the microphone. Install the 3 screws (removed in step 1)

to secure the tube.

Shure Incorporated

5/9

4. Drill a 143 mm (5 5/8 in.) hole through the table, and then place the tray into the hole.

Shure Incorporated

6/9

5. Guide the cable through the hole in the center of the tray. Then, place the tube through the hole in the table

and gently press the microphone into the tray. Align the Shure logo on the microphone with the Shure logo on

the tray. The four rubber feet on the bottom of the microphone fit into the four smaller holes in the tray.

Shure Incorporated

7/9

6. Place the bracket underneath the table, with the tube going through the hole. For thicker tables (≥ 55 mm), turn

the bracket upside down for additional clearance.

Note: maximum table thickness = 73 mm (2.87 in).

Shure Incorporated

8/9

7. Guide the cable through the wing nut, and attach the wing nut onto the tube from underneath the table. Then,

tighten the wing nut to secure the bracket against the table.

Optional: use the hole in the wing nut to insert a cable tie for cable management.

Shure Incorporated

9/9

Dimensions

Altri manuali per A310-FM

Indice

Manuali Rack e supporto popolari di altre marche

Salamander

Salamander Acadia AC/W/L400/WH Manuale utente

Fohhn

Fohhn VAT-09 Guida utente

ricoo

ricoo FS0522 Manuale utente

AMSOIL

AMSOIL BMK-22 Guida rapida

Kargo Master

Kargo Master 48220 Manuale utente

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuale utente

ricoo

ricoo S1222 Manuale utente

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuale utente

VidaBox

VidaBox VB MNT FFS2 Manuale utente

Welch Allyn

Welch Allyn 48960 Manuale utente

Arkon

Arkon CM035-ST-2 Manuale utente

PROEL

PROEL PLWIN60C Manuale utente

Agilent Technologies

Agilent Technologies E2609B Manuale utente

Mustang

Mustang MV-ARM4 Manuale utente

Mounting Solutions

Mounting Solutions WRM-320 Manuale utente

Pyle

Pyle PMKSPAD1 Manuale utente

ShelterIt

ShelterIt 21208 Manuale utente

SPL

SPL RackPack?4 1040 Manuale utente