SI 201576 Manuale utente
DECOSET KEYPAD
Installation Instructions
# 201576
SET UPPER
SET LOWER
REVERSE
UP
DOWN
STOP
Thank you for purchasing an SI product. If you have any
questions or need any assistance with your Decoset, we
would love to help you.
Technical Support: 512.832.6939
Hours of Support: 7:30am - 5pm CST
screeninnovations.com
Decoset
Please use these QR Codes to access the updated
installation instructions and video tutorials.
CONTENTS
4
PARTS IN THE BOX
8 button keypad
- base
Parts in the Box
White trim
wall plate
(2)Trim plate screws (2)Insert screws
(1)Decoset interface
8 button
Decora insert
5 button
Decora insert
(1) Cate 5e cable
485 Motor Interface
485 Motor only
5
INITIAL CONSIDERATIONS
The Decoset is a pre-programmed control keypad/limit
setting tool. And is designed to allow you to set the limits
and adjust the rotation on your 485 screen/shade without
the use of a PC or any other hardware.
Once you complete your setup, then the keypad can be used
to control the 485 screen/shade and installed in a wall.
Initial considerations & Setup steps
SETUP STEPS
Review the following pages (6 - 8) to determine if your
screen/shade is an AC or Low-Voltage powered.
If you already know that you have a Low-Voltage screen
then skip to page 9.
6
WIRING TOPOLOGY - AC 485
SCREENS
Wiring topology - AC 485 screens
3 conductors
(up to100') Decoset
Interface
Terminal
Block
RJ45
Solo/Pro 2 screen
AC Power
Supply
485 Motor Interface
485 Motor only
V+
V-
+
-
G
7
CONNECTING TO AC 485 SCREENS
1. Connect the Terminal Block coming from your screen
to the 485 interface
2. You can now connect your Decoset to the keypad port
of the interface.
Note: If you need to extend the length of cable to your
Decoset, you can use standard Cat5e up to 100 ft.
Connecting to AC 485 screens
8
3. Once your Decoset is connected to the screen and the
screen has AC power applied, a small red LED will start
flashing directly above the RJ45 connector on the back of
the Decoset.
Note: If this does not happen, then check the AC power
You're now ready to start configuring your screen/shade.
Skip to Page 15 for next steps.
Connecting to AC 485 screens
Flashing Red LED to
indicate power
9
WIRING TOPOLOGY - LV 485
MOTORS
Power Supply
Cat 5e
(100ft)
Decoset
Solo/Pro 2 screen / Nano shades
Note: Most all LV motors will come with a cable terminated
into a 5 position terminal block.
V+
V-
+
-
G
V+
V-
+
-
G
Wiring topology - LV 485 motors
485 Motor Interface
485 Motor only
Note: The 485 Motor Interface power LED will illuminate
green whenever LV power is applied to your shade/screen.
10
CONNECTING TO LV 485 MOTORS
1. The included 485 Motor Interface provides connections
for the 5 conductor wire coming from the screen/shade
and the wire coming from the low-voltage power supply
and a connection for Decoset via Cat5e.
2. Make all the 485 Moto Interface connections first, then
apply power via low-voltage power supply.
485 Moto Interface
From the
screen/
shade
RJ45
V+
V-
+
-
G
To low-Voltage power supply
+ 24 VDC
- 24 VDC
Not
used
V+V+
V-V-
++
--
GG
Connecting to LV 485 motors
485 Motor Interface
485 Motor only
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali SI Tastiera
