Siebert S302 Series Manuale utente

Pos: 2/ Siebert/Bedie nungsanleitungen/ Serie S302/SX302/ BAL ab 2017/Titelseite n/Titelseite S302 EIP @ 4\mod_14891 39392419_48.d ocx @ 27264 @ @ 1

Series S302

Numeric large size displays

with EtherNet/IP interface

Operating instructions

Pos: 3/ Siebert/Seite numbruch @ 0\mod_ 1314194553878_0.d ocx @ 150 @ @ 1

BAL S302 EIP 1.11 2/21

Pos: 4/ Siebert/Bedienungs anleitungen/Gerät ebeschreibung Grossanz eigen alleS erien/Kontakt @ 1\ mod_1339668951540_4 8.docx@ 4 323 @ 1@ 1

1 Contact

www.siebert-group.com

GERMANY

Siebert Industrieelektronik GmbH

Siebertstrasse, D-66571 Eppelborn

P.O. Box 11 30, D-66565 Eppelborn

Phone +49 (0)6806 980-0, Fax +49 (0)6806 980-999

email: info.de@siebert-group.com

AUSTRIA

Siebert Österreich GmbH

Mooslackengasse 17, A-1190 Wien

Phone +43 (0)1 890 63 86-0, Fax +43 (0)1 890 63 86-99

email: info.at@siebert-group.com

FRANCE

Siebert France Sarl

4 rue de l’Abbé Louis Verdet, F-57200 Sarreguemines

P.O. Box 90 334, F-57203 Sarreguemines Cédex

Phone +33 (0)3 87 98 63 68, Fax +33 (0)3 87 98 63 94

email: info.fr@siebert-group.com

ITALY

Siebert Italia Srl

Via Galileo Galilei 2A, I-39100 Bolzano (BZ)

Phone +39 (0)471 053753 Fax +39 (0)471 053754

email info.it@siebert-group.com

THE NETHERLANDS

Siebert Nederland B.V.

Jadedreef 26, NL-7828 BH Emmen

Phone +31 (0)591-633444, Fax +31 (0)591-633125

email: info.nl@siebert-group.com

SWITZERALND

Siebert AG

Bützbergstrasse 2, P.O. Box 91, CH-4912 Aarwangen

Phone +41 (0)62 922 18 70, Fax +41 (0)62 922 33 37

email: info.ch@siebert-group.com

Pos: 5/ Siebert/Seite numbruch @ 0\mod_ 1314194553878_0.d ocx @ 150 @ @ 1

BAL S302 EIP 1.11 3/21

Pos: 6/ Siebert/Bedienungs anleitungen/Gerät ebeschreibung Grossanz eigen alleS erien/Rechtlicher Hin weis@ 1 \mod_133966887 8995_48.docx @ 4317 @ 1 @ 1

2 Legal note

This operation manual has been prepared with the utmost care. However, we do not accept any

liability for possible errors. We always appreciate your suggestions for improvement, corrections,

comments and proposals. Please contact us: editing@siebert-group.com

Siebert®, LRD®and XC-Board®are registered trademarks of Siebert Industrieelektronik GmbH. All

other product names mentioned herein may be trademarks or registered trademarks of their respective

owners.

We reserve the right to make alterations to the technical data and delivery options without notice. - All

rights reserved, including the rights of translation. No part of this document may in any form or by any

means (print, photocopy, microfilm or any other process) be reproduced or by using electronic

systems be processed, copied or distributed without our written permission.

Pos: 7/ Siebert/Seitenum bruch @ 0\mod_13141945 53878_0.docx @ 150 @ @ 1

BAL S302 EIP 1.11 4/21

Pos: 8/ Siebert/Bedienungs anleitungen/Modul Inh altsverzeichnis @ 1\mod_1 352981287156_48. docx@ 51 55@ @ 1

Table of contents

1Contact 2

2Legal note 3

3Safety precautions 5

Important information .........................................................................................................................................5

Safety .................................................................................................................................................................5

Intended use.......................................................................................................................................................5

Mounting and installation....................................................................................................................................5

Grounding...........................................................................................................................................................5

EMC measures...................................................................................................................................................6

Disposal..............................................................................................................................................................6

4Model designation 7

Unit construction.................................................................................................................................................7

5Number format 8

6IP settings 8

7Data format 10

8Messages on the display 11

9Setting the display type via Properties 12

Number to be displayed Raw Value ................................................................................................................12

Decimal points Decimal Dots ..........................................................................................................................12

Offset, scale factor (multiplier), and divisor .....................................................................................................12

Threshold values Range .................................................................................................................................13

Flags ................................................................................................................................................................13

Attributes for flashing and blinking modes ......................................................................................................13

Format .............................................................................................................................................................13

10 Flashing modes and display attributes 14

11 Flags 15

12 Setting the basic brightnesst 16

13 Technical data 17

Fieldbus............................................................................................................................................................17

Power supply....................................................................................................................................................17

Housing colors..................................................................................................................................................17

Ambient conditions...........................................................................................................................................17

Unit properties..................................................................................................................................................18

Max. power consumption .................................................................................................................................19

Dimensions and weights ..................................................................................................................................20

=== Ende der Liste für Te xtmarke Inhalt1 ===

Pos: 10 /Siebert/Seitenu mbruch@ 0 \mod_1314194 553878_0.docx @ 150 @ @ 1

BAL S302 EIP 1.11 5/21

Pos: 11 /Siebert/Bedi enungsanleitunge n/Gerätebeschrei bung Grossanzeige n alle Serien/Sicherh eitshinweise Gross anzeigen @ 1\mod_13 85723449297_4 8.docx @ 7018 @ 1222222 2 @1

3 Safety precautions

Important information

Read these operating instructions before starting the unit. They provide you with important information

on the use, safety and maintenance of the units. This helps you to protect yourself and prevent

damage to the unit.

Information intended to help you to avoid death, bodily harm or considerable damage to

property is highlighted by the warning triangle shown here; it is imperative that this

information be properly heeded.

The operating instructions are intended for trained professional electricians familiar with the safety

standards of electrical technology and industrial electronics.

Store these operating instructions in an appropriate place.

The manufacturer is not liable if the information in these operating instructions is not complied with.

Safety

Components inside the units are energized with electricity during operation. For this reason,

mounting and maintenance work may only be performed by professionally-trained personnel

while observing the corresponding safety regulations.

The repair and replacement of components and modules may only be carried out by the manufacturer

for safety reasons and due to the required compliance with the documented unit properties.

The units do not have a power switch. They are operative as soon as the operating voltage is applied.

Intended use

The units are intended for use in industrial environments. They may only be operated within the limit

values stipulated by the technical data.

When configuring, installing, maintaining and testing the units, the safety and accident-prevention

regulations relevant to use in each individual case must be complied with.

Trouble-free, safe operation of the units requires proper transport, storage, installation, mounting and

careful operation and maintenance of the units.

Mounting and installation

The attachment options for the units were conceived in such a way as to ensure safe, reliable

mounting.

The user must ensure that the attachment hardware, the unit carrier and the anchoring at the

unit carrier are sufficient to securely support the unit under the given surrounding conditions.

The units are to be mounted in such a way that they can be opened up while mounted. Sufficient

space for the cables must be available in the unit near the cable entries.

Sufficient space is to be kept clear around the units to ensure air circulation and to prevent the build-

up of heat resulting from use. The relevant information must be heeded in the case of units ventilated

by other means.

When the housing fasteners are opened, the front frame of the housing hinges out upward or

downward (depending on the unit version) automatically.

Grounding

All devices are equipped with a metal housing. They comply with safety class I and require a

protective earth connection. The connecting cable for the operating voltage must contain a protective

earth wire of a sufficient cross section (DIN VDE 0106 part 1, DIN VDE 0411 part 1).

BAL S302 EIP 1.11 6/21

EMC measures

The devices comply with the current EU Directive (EMC Directive) and provide the required

interference immunity. Observe the following when connecting the operating voltage and data cables:

Use shielded data cables.

The data and operating voltage cables must be laid separately. They may not be laid together with

heavy-current cables or other interference-producing cables.

The cable thickness must be properly assessed (DIN VDE 0100 Part 540).

The cable lengths inside the units are to be kept as short as possible to prevent interference. This

applies especially to unshielded operating voltage cables. Shielded cables are also to be kept short

due to any interference which might be emitted by the shielding.

Neither excessively long cables nor cable loops may be placed inside the units.

The connection of the cable shielding to the functional ground (PE) must be as short and low-

impedance as possible. It should be made directly to the mounting plate over a large area with a

conductive clip:

①mounting plate

②conductive clamp

③data lines

④cable shielding

The cable shielding is to be connected at both cable ends. If equipotential bonding currents are

expected due to the cable arrangement, electrical isolation is to be performed on one side. In this

case, capacitive connection (approx. 0.1μF/600 V AC) of the shielding on the isolated side must occur.

Disposal

Units or unit parts which are no longer needed are to be disposed of in accordance with the

regulations in effect in your country.

Pos: 12 /Siebert/Seit enumbruch @ 0\mod _1314194553878_0. docx @ 150 @ @ 1

BAL S302 EIP 1.11 7/21

Pos: 13 /Siebert/Bedi enungsanleitunge n/Serie S302/SX30 2/BAL ab 2017/Geltungsb ereich/ÜBS Gelt ungsbereich @ 4\ mod_148914037706 0_48.docx @ 27276 @ 1@ 1

4 Model designation

Pos: 14 /Siebert/Bedi enungsanleitunge n/Serie S302/SX30 2/BAL ab 2017/Geltung sbereich/S302 Gel tungsbereich EIP @ 4 \mod_1489140 493240_48.docx @ 27 283 @ @ 1

This manual applies to units with the following model designation (x = the 'x's in the model designation

indicate the size and design of the units)

S302-xx/xx/xx-xxx/xx-YE

Pos: 15 /Siebert/Bedi enungsanleitunge n/Serie S302/SX30 2/BAL ab 2017/Geräte aufbau/S302 Geräte aufbau EIP @ 4\mod_ 1489141182238_ 48.docx @ 27290 @ 2 @ 1

Unit construction

The following figure shows model type S302-05/10/xx-xxx/xx-xx as example for the other model types.

The front frame of the housing is locked with quick-action releases. When opening the unit the front

frame hinges downward.

The following figure shows the unit when open.

Central

Processing

Unit

Power supply

unit

Display modules

Units with double-sided display show the same information on the front and on the rear side.

Pos: 16 /Siebert/Seitenu mbruch@ 0 \mod_1314194 553878_0.docx @ 150 @ @ 1

BAL S302 EIP 1.11 8/21

Pos: 17 /Siebert/Bedi enungsanleitunge n/Serie S302/SX30 2/BAL ab 2017/Zahle nformat/ÜBS Zahle nformat @ 4\mod_1 489142000307_48.d ocx @ 27297 @ 1 @ 1

5 Number format

Pos: 18 /Siebert/Bedi enungsanleitunge n/Serie S302/SX30 2/BAL ab 2017/Zahlenf ormat/S302 Zahlenfor mat EIP @ 4\mod_ 148914207476 0_48.docx @ 27304 @ @ 1

Numbers in this manual are displayed hexadecimal and decimal.

Hexadecimal numbers are always shown with the prefix '16 # 'and depending on the application with

leading zeros. The lowest value digit is on the right.

Example: The decimal number '10' equals '16#A' or '16#0A', the decimal number 100 equals '16#64'

or '16#0064'.

Decimal numbers do not have a special marking.

Pos: 19 /Siebert/Bedi enungsanleitunge n/Serie S302/SX30 2/BAL ab 2017/IP-Eins tellungen/ÜBS IP-Ei nstellungen @ 4\ mod_148914312769 2_48.docx @ 2731 0 @ 1@ 1

IP-Einstellungen

6 IP settings

Pos: 21 /Siebert/Bedi enungsanleitunge n/Serie S302/SX30 2/BAL ab 2017/IP-Eins tellungen/S302 IP-Ei nstellungen EIP abV ersion 1.10 @ 4\mo d_149449321867 2_48.docx @ 29054 @ @ 1

The following parameters are set in the factory setting:

IP address: 192.168.20.250

Subnet mask: 255.255.255.0

Gateway: 0.0.0.0

DHCP: Off

The values can be changed in an engineering framework (for example Rockwell Studio 5000).

Alternatively, you can change the IP settings using the program 'EtherNet/IP Tool'. You find the

program on the data carrier included in delivery as a ZIP archive file or on www.siebert-group.com.

After unpacking this file, the program 'EthernetIPTool.exe' can be run without installation.

After the program is started the following window opens and an automatic search for EtherNet/IP-

devices is started. For a new search click on the 'Refresh' button on the top right.

Double-clicking on the display whose settings you want to change opens the following window:

BAL S302 EIP 1.11 9/21

Enter the desired IP settings and click the 'OK' button. After successful configuration the following

window opens:

After that the display carries out a restart and can be accesses via the new IP settings.

The windows is closed by clicking 'OK' once and a new search for EtherNet/IP-devices starts.

Pos: 22 /Siebert/Seitenu mbruch@ 0 \mod_1314194 553878_0.docx @ 150 @ @ 1

BAL S302 EIP 1.11 10/21

Pos: 23 /Siebert/Bedi enungsanleitunge n/Serie S302/SX30 2/BAL ab 2017/Date nformat/ÜBS Daten format @ 4\mod_14 89144336829_48.d ocx @ 27323 @ 1 @ 1

Datenformat

7 Data format

Pos: 24 /Siebert/Bedi enungsanleitunge n/Serie S302/SX30 2/BAL ab 2017/Date nformat/S302 Datenf ormat EIP @ 4\mod_ 1489144370680_48. docx @ 27330 @ @ 1

The EDS data file is included in delivery or see on www.siebert-group.com.

The name of the display is 'S302-YE' and it uses the following settings:

Parameter

Originator to Target (O T)

Target to Originator (T O)

Instance ID

150

100

Data size

6 bytes

0 bytes

The display always receives 6 bytes: 4 bytes for the value and 2 bytes, which specify the meaning of

the sent value. The following E/A-image is used:

Channel

Address

Description

Property

%QW0

2 bytes property identifier

Value

%QD1

4 bytes value signed

Example 1: The decimal number '15' has to be shown on the display.

As Property 16#0100' and as Value '16#0000_000F' has to be send.

Because EtherNet/IP uses the byte order little-endian the bytes are sent as follows:

16 bit Property

32 bit signed number

%QW0 = 16#0100

%QD1 = 16#0000_000F (equals with the decimal number '+15')

%QB0

%QB1

%QB2

%QB3

%QB4

%QB5

16#00

16#01

16#0F

16#00

Example 2: The decimal number '-15' has to be shown on the display.

As Property '16#0100' and as Value '16#FFFF_FFF1' has to be send.

Because EtherNet/IP uses the byte order little-endian the bytes are sent as follows:

16 bit Property

32 bit signed number

%QW0 = 16#0100

%QD1 = 16#FFFF_FFF1 (equals with the decimal number '-15')

%QB0

%QB1

%QB2

%QB3

%QB4

%QB5

16#00

16#01

16#F1

16#FF

The possible display types (Properties) are described in the chapter 'Setting the display type via

Properties'.

Pos: 25 /Siebert/Seit enumbruch @ 0\mod _1314194553878_0. docx @ 150 @ @ 1

Altri manuali per S302 Series

Indice

Altri manuali Siebert Monitor

Siebert

Siebert XC610 Series Manuale utente

Siebert

Siebert XC420 Series Manuale utente

Siebert

Siebert XC630 Series Manuale utente

Siebert

Siebert Series S102 Manuale utente

Siebert

Siebert S302 Serie Manuale utente

Siebert

Siebert S302 Series Manuale utente

Siebert

Siebert Series S102 Manuale utente

Siebert

Siebert Series S102 Manuale utente

Siebert

Siebert XC460 Series Manuale utente

Siebert

Siebert Series S102 Manuale utente

Siebert

Siebert SX502 Series Manuale utente

Siebert

Siebert XC600 Series Manuale utente

Siebert

Siebert SX502 Series Manuale utente

Siebert

Siebert XC410 Series Manuale utente

Siebert

Siebert Series S102 Manuale utente

Siebert

Siebert S302 Series Manuale utente

Siebert

Siebert SX302 Series Manuale utente

Siebert

Siebert XC640 Series Manuale utente

Siebert

Siebert Series S102 Manuale utente

Siebert

Siebert XC610 Series Manuale utente

Siebert

Siebert XC695 Series Manuale utente

Siebert

Siebert XC620 Series Manuale utente

Siebert

Siebert Series S102 Manuale utente

Siebert

Siebert SX602 series Manuale utente

Manuali Monitor popolari di altre marche

Linear Acoustic

Linear Acoustic LQ-1000 Manuale utente

AOC

AOC I2579V Manuale utente

Gateway

Gateway FPD1520 Manuale utente

Furuno

Furuno Mu 120c Manuale utente

Asus

Asus VB171D - 17" LCD Monitor Manuale utente

Dell

Dell S2230MX Istruzioni utente

Philips

Philips 107C64 Manuale utente

Dell

Dell S2409WFP Manuale utente

EverFocus

EverFocus EN-7517E Manuale utente

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuale utente

Dell

Dell Precision 7680 Manuale di istruzioni

LG 50PM1M - - 50" Plasma Panel Manuale utente

Bosch

Bosch DDU 9 Manuale utente

Acer

Acer A231HL Manuale utente

Philips

Philips 86BDL4152T Manuale utente

NEC

NEC AccuSync LCD5V Manuale utente

Emay

Emay SleepO2 Manuale utente

IBM

IBM 6360 Istruzioni per l'installazione