Siemens SITRANS FC430 Guida rapida

A5E33310535-AG, 06/2016 1

FC430 upgrade instructions - Compact

Product Information

Introduction

The purpose of these upgrade instructions is to assist technicians in upgrading the FC430 system from sales release 1 (HW

revision 1 and FW version 3.00.0*-**).

The instructions are aimed at service and maintenance technicians.

Items supplied

FC430 upgrade package for compact systems, A5E34574738, contains the following components:

Component

Photo

SITRANS FCS400 Sensor cassette

4 GB micro SD card (SensorFlash) with Micro SD

card adapter containing:

•Firmware bundle

•FC430 Upgrade instructions - Compact

Note: Firmware bundle and upgrade instructions may

also be downloaded from the Intranet at:

(http://support.automation.siemens.com/WW/view/en

/60666565/133300)

Power supply unit

FC430 Upgrade instructions - Compact

Order number: A5E33310535

FC430 upgrade package for compact version

FC430 upgrade instructions - Compact

2A5E33310535-AG, 06/2016

Upgrading the FC430 system

The upgrade procedure includes the following main steps:

1. Remove and back up SensorFlash (SD card) (Page 2)

2. Replace sensor cassette (Page 3)

3. Replace power supply (Page 5)

4. Upgrade firmware (Page 7)

5. Synchronize data (Page 7)

Before carrying out any repair work, the instructions for safe handling of the device must be read and understood. See

Operating Instructions.

Remove and back up SensorFlash (SD card)

①

Isolate the device from power.

②Unscrew the locking screw of the display lid and remove lid.

③

Using a plain screwdriver, carefully release the display as shown in the following photo.

FC430 upgrade instructions - Compact

A5E33310535-AG, 06/2016 3

④

Remove the SensorFlash (SD card) from the transmitter. Insert the SensorFlash into a PC using the SD card

adapter and create a backup of all files from the card to a PC.

Note: Do not re-insert the SD card in the transmitter at this point. You will need the SensorFlash again later, see

Synchronize data (Page 7).

Replace sensor cassette

Remove sensor cassette

①Remove the two screws that hold the sensor cassette.

②

Pull out the sensor cassette to the position shown in the photo.

FC430 upgrade instructions - Compact

4A5E33310535-AG, 06/2016

③

Disconnect the cable plug while lifting the catch and remove the sensor cassette.

Remove transmitter and I/O cassettes

①

Remove the two screws that hold the transmitter I/O cassettes.

②Pull out the two cassettes.

FC430 upgrade instructions - Compact

A5E33310535-AG, 06/2016 5

Replace power supply

Remove power supply

①

Unscrew three fixing screws for power supply cover and pull out the cover.

②Using a pair of point nose pliers, pull out the triangular housing with the power supply cassette.

FC430 upgrade instructions - Compact

6A5E33310535-AG, 06/2016

Install new power supply and interface cassette

Insert the new power supply delivered with the upgrade kit as follows:

①Carefully slide the new power supply into the triangular housing and reinsert in the transmitter.

②

Reinsert I/O and transmitter cassettes.

Insert the new sensor cassette (HW revision RSAA) delivered with the kit as follows:

③Hold down the cable while pushing the new sensor cassette to the position shown in the photo.

④

Reconnect cassette cable plug and push sensor cassette into place. Fasten the two screws.

⑤

Connect the display cable, and leave the display unattached as shown in photo.

⑥

Return power to the device.

FC430 upgrade instructions - Compact

A5E33310535-AG, 06/2016 7

Upgrade firmware

Follow these steps to upgrade the firmware using the local user display:

NOTICE

SensorFlash

Do NOT remove the SensorFlash during the update.

①

Insert the new SensorFlash delivered with the upgrade package into the transmitter.

②

On the display press from one of the measurement views. Sign in as "Expert" (default password 2834).

③Go to menu item 3.1.10 "Firmware Revision", change the parameter to new FW version "3.02.02-01" and confirm by

pressing .

④Wait 2-3 minutes before the update starts. The update takes approximately 10 minutes and the transmitter makes a

restart after a successful update.

The display flashes and indicates progress during the update.

⑤

After the restart the display shows the wizard "First startup" .The firmware update does not change the configuration,

but you must go through the basic parameters to confirm the settings (display language, date, time).

Select "No" when asked if you want to go through the Quick commissioning wizard.

Synchronize data

To complete the upgrade, the new sensor electronic must be synchronized with the original SensorFlash data.

①Remove power from the device.

Remove the SensorFlash from the transmitter and insert original one.

②

Return power to the device.

Alarm 151 "Sensor serial number mismatch" will appear in the display. SensorFlash backup is not possible due to

serial number mismatch between sensor front-end and SensorFlash. Sensor flash data, for example backup data for

sensor calibration, from the replaced sensor electronic must be copied from the SensorFlash to the new electronic.

Proceed as follows to synchronize the data and clear alarm 151.

③Sign in as "Expert" (default password 2834).

Go to menu item 3.3.7.2.2 "Replace Sensor Cassette (Compact)" and press . Select "OK" and press to start

the synchronization.

Synchronization updates data between SensorFlash and sensor electronic. Alarm 151 disappears and all

parameters are backed up in the SensorFlash.

④

Verify the data synchronization: Go to menu item 3.1.14.4 "Serial number" (sensor), and ensure that the number

matches the sensor serial number on the sensor product label.

Note: If alarm 151 "Sensor serial number mismatch" appears, then repeat steps 3-4.

Note

Update PID parameters

For update of PID parameters, see FAQ (

https://support.industry.siemens.com/cs/ww/en/view/109738556).

FC430 upgrade instructions - Compact

8A5E33310535-AG, 06/2016

Fraction variant

New fraction configurations are made available in the new firmware. The following step must be performed for fraction

configured flowmeters:

①Go to menu item 2.2.7.3 "Active Fraction" and press . From the list, select the fraction used in the application,

and press .

Note: If the ordered fraction is not found on the list, then select the last option "Empty".

Reinstate display and display lid

①

Reconnect display cable and carefully push display back into housing.

②Remove the O-ring from the lid.

③

Reinstate the display lid until mechanical stop. Wind back the lid by one turn.

④

Mount the O-ring by pulling it over the display lid; then turn the lid until you feel friction from the O-ring on both sides.

⑤Wind the display lid by one quarter of a turn to seal on the O-ring and tighten the fixing screw.

FC430 upgrade instructions - Compact

A5E33310535

, 06/2016

Siemens AG

Division Process Industries and Drives

Postfach 48 48

90026 NÜRNBERG

GERMANY

A5E33310535-AG, 06/2016 9

FC430 Upgrade-Anweisungen – Kompakt

Produktinformation

Einleitung

Zweck dieser Upgrade-Anweisungen ist die Unterstützung von Technikern beim Upgrade des FC430 Systems mit

Vertriebsfreigabe 1 (HW-Version 1 und FW-Version 3.00.0*-**).

Die Anweisungen richten sich an Service- und Wartungstechniker.

Lieferumfang

Das FC430 Upgrade-Paket für Kompaktsysteme, A5E34574738, enthält die folgenden Komponenten:

Komponente

Foto

Messaufnehmerkassette SITRANS FCS400

4-GB-MicroSD-Karte (SensorFlash) mit MicroSD-

Kartenadapter mit:

•Firmware-Bundle

•FC430 Upgrade-Anweisungen - Kompakt

Hinweis: Firmware-Bundle und Upgrade-

Anweisungen können auch im Intranet

heruntergeladen werden unter:

(http://support.automation.siemens.com/WW/view/de

/60666565/133300)

Netzteil

FC430 Upgrade-Anweisungen – Kompakt

Bestellnummer: A5E33310535

FC430 Upgrade-Paket für Kompaktausführung

FC430 Upgrade-Anweisungen – Kompakt

10 A5E33310535-AG, 06/2016

Upgrade des FC430 Systems

Die Upgrade-Vorgehensweise umfasst die folgenden Schritte:

1. SensorFlash (SD-Karte) ausbauen und Sicherungskopie anfertigen (Seite 10)

2. Messaufnehmerkassette ersetzen (Seite 11)

3. Netzteil austauschen (Seite 13)

4. Firmware aktualisieren (Seite 15)

5. Daten synchronisieren (Seite 15)

Bevor Sie Reparaturarbeiten ausführen, müssen Sie die Anweisungen zur sicheren Handhabung des Geräts gelesen und

verstanden haben. Siehe Betriebsanleitung.

SensorFlash (SD-Karte) ausbauen und Sicherungskopie anfertigen

①

Schalten Sie das Gerät spannungsfrei.

②Drehen Sie die Sicherungsschraube des Anzeigedeckels heraus und nehmen Sie den Deckel ab.

③

Lösen Sie mit einem einfachen Schraubendreher vorsichtig die Anzeige wie im folgenden Foto gezeigt.

Altri manuali per SITRANS FC430

Indice

Lingue:

Altri manuali Siemens Accessori

Siemens

Siemens QFM3100 Manuale di servizio

Siemens

Siemens TC63 Guida all'installazione

Siemens

Siemens SIWAREX WP321 Manuale utente

Siemens

Siemens Symaro QAA2890/WI Manuale utente

Siemens

Siemens SIWAREX JB Guida per l'amministratore

Siemens

Siemens QMX3.P35H Series Manuale utente

Siemens

Siemens SIPART Series Guida per l'amministratore

Siemens

Siemens A80850 Manuale utente

Siemens

Siemens SITRANS LVL200S Manuale utente

Siemens

Siemens RUGGEDCOM WIN7237 Manuale utente

Siemens

Siemens Milltronics RBSS Manuale utente

Siemens

Siemens SIMATIC MOBY D Guida utente

Siemens

Siemens Milltronics BW100 Manuale utente

Siemens

Siemens QAA4292.EWSC Manuale utente

Siemens

Siemens WEPS Manuale utente

Siemens

Siemens SITRANS WS300 Manuale di servizio

Siemens

Siemens SIWAREX WP321 Manuale utente

Siemens

Siemens SITRANS WS300 Manuale utente

Siemens

Siemens 8WD44 Manuale utente

Siemens

Siemens 1218RF Manuale utente

Siemens

Siemens jpQO Manuale utente

Siemens

Siemens 3VT9200-4PA30 Manuale utente

Siemens

Siemens SITRANS WS300 Manuale utente

Siemens

Siemens Milltronics ILE-61 Manuale utente

Manuali Accessori popolari di altre marche

Hillco

Hillco 2810 Manuale utente

Contours

Contours ZY024 Manuale utente

Saivod

Saivod VS621 Manuale utente

Virtuox

Virtuox VirtuCLEAN 2.0 Manuale utente

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuale utente

Z-Wave

Z-Wave HSD-200Z Manuale utente

turck

turck FMX-IM-2UPLI63FX Manuale utente

Decagon Devices

Decagon Devices 10HS Manuale utente

UPPAbaby

UPPAbaby Cup Holder Manuale utente

Elko

Elko SmartSensor Leakage Wireless Manuale utente

Grizzly

Grizzly H8371 Manuale utente

Panasonic

Panasonic HG-T Series Manuale utente

IFM Electronic

IFM Electronic Efector 250 Series Guida di riferimento

DigiDesign

DigiDesign 888/24 I/O Manuale utente

PROZIS

PROZIS QUAY Manuale utente

patagonia

patagonia PSI Vest Manuale utente

SFC Energy

SFC Energy EFOY GO! Manuale utente

Axminster

Axminster Tooling Stylus Tip Ballpoint Pen Kit Manuale utente