Siemens SINUMERIK ONE MCP 2400 Documento tecnico
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage
to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices
referring only to property damage have no safety alert symbol. These notices shown below are graded according to
the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will be
used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property
damage.
Qualied Personnel
The product/system described in this documentation may be operated only by personnel qualied for the specic
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualied personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended or
approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance
are required to ensure that the products operate safely and without any problems. The permissible ambient
conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identied by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication may
be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software described.
Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this
publication is reviewed regularly and any necessary corrections are included in subsequent editions.
Siemens AG
Digital Industries
Postfach 48 48
90026 NÜRNBERG
GERMANY
Document order number: A5E50324707B AA
Ⓟ 10/2020 Subject to change
Copyright © Siemens AG 2020.
All rights reserved
Table of contents
1 Fundamental safety instructions ........................................................................................................... 5
1.1 General safety instructions................................................................................................... 5
1.2 Equipment damage due to electric elds or electrostatic discharge ....................................... 8
1.3 Warranty and liability for application examples ..................................................................... 9
1.4 Security information ............................................................................................................ 9
1.5 Residual risks of power drive systems ................................................................................. 10
2 Overview.............................................................................................................................................. 13
3 Dimension drawings............................................................................................................................ 15
4 Operator control and display elements ............................................................................................... 17
4.1 Front side .......................................................................................................................... 17
4.2 Rear side............................................................................................................................ 18
5 Technical data...................................................................................................................................... 19
Index .................................................................................................................................................... 23
ONE MCP Part 2: MCP 2400
Equipment Manual, 07/2020, A5E50324707B AA 3
Table of contents
ONE MCP Part 2: MCP 2400
4Equipment Manual, 07/2020, A5E50324707B AA
Fundamental safety instructions 1
1.1 General safety instructions
WARNING
Electric shock and danger to life due to other energy sources
Touching live components can result in death or severe injury.
• Only work on electrical devices when you are qualied for this job.
• Always observe the country-specic safety rules.
Generally, the following steps apply when establishing safety:
1. Prepare for disconnection. Notify all those who will be aected by the procedure.
2. Isolate the drive system from the power supply and take measures to prevent it being
switched back on again.
3. Wait until the discharge time specied on the warning labels has elapsed.
4. Check that there is no voltage between any of the power connections, and between any of
the power connections and the protective conductor connection.
5. Check whether the existing auxiliary supply circuits are de-energized.
6. Ensure that the motors cannot move.
7. Identify all other dangerous energy sources, e.g. compressed air, hydraulic systems, or
water. Switch the energy sources to a safe state.
8. Check that the correct drive system is completely locked.
After you have completed the work, restore the operational readiness in the inverse sequence.
WARNING
Electric shock due to connection to an unsuitable power supply
When equipment is connected to an unsuitable power supply, exposed components may carry
a hazardous voltage. Contact with hazardous voltage can result in severe injury or death.
• Only use power supplies that provide SELV (Safety Extra Low Voltage) or PELV- (Protective
Extra Low Voltage) output voltages for all connections and terminals of the electronics
modules.
ONE MCP Part 2: MCP 2400
Equipment Manual, 07/2020, A5E50324707B AA 5
WARNING
Electric shock due to equipment damage
Improper handling may cause damage to equipment. For damaged devices, hazardous
voltages can be present at the enclosure or at exposed components; if touched, this can result
in death or severe injury.
• Ensure compliance with the limit values specied in the technical data during transport,
storage and operation.
• Do not use any damaged devices.
WARNING
Electric shock due to unconnected cable shields
Hazardous touch voltages can occur through capacitive cross-coupling due to unconnected
cable shields.
• As a minimum, connect cable shields and the cores of cables that are not used at one end
at the grounded housing potential.
WARNING
Electric shock if there is no ground connection
For missing or incorrectly implemented protective conductor connection for devices with
protection class I, high voltages can be present at open, exposed parts, which when touched,
can result in death or severe injury.
• Ground the device in compliance with the applicable regulations.
NOTICE
Damage to equipment due to unsuitable tightening tools.
Unsuitable tightening tools or fastening methods can damage the screws of the equipment.
• Be sure to only use screwdrivers which exactly match the heads of the screws.
• Tighten the screws with the torque specied in the technical documentation.
• Use a torque wrench or a mechanical precision nut runner with a dynamic torque sensor and
speed limitation system.
Fundamental safety instructions
1.1 General safety instructions
ONE MCP Part 2: MCP 2400
6Equipment Manual, 07/2020, A5E50324707B AA
WARNING
Spread of re from built-in devices
In the event of re outbreak, the enclosures of built-in devices cannot prevent the escape of
re and smoke. This can result in serious personal injury or property damage.
• Install built-in units in a suitable metal cabinet in such a way that personnel are protected
against re and smoke, or take other appropriate measures to protect personnel.
• Ensure that smoke can only escape via controlled and monitored paths.
WARNING
Unexpected movement of machines caused by radio devices or mobile phones
Using radio devices or mobile telephones in the immediate vicinity of the components can
result in equipment malfunction. Malfunctions may impair the functional safety of machines
and can therefore put people in danger or lead to property damage.
• Therefore, if you move closer than 20 cm to the components, be sure to switch o radio
devices or mobile telephones.
• Use the "SIEMENS Industry Online Support app" only on equipment that has already been
switched o.
WARNING
Fire due to inadequate ventilation clearances
Inadequate ventilation clearances can cause overheating of components with subsequent re
and smoke. This can cause severe injury or even death. This can also result in increased
downtime and reduced service lives for devices/systems.
• Ensure compliance with the specied minimum clearance as ventilation clearance for the
respective component.
NOTICE
Overheating due to inadmissible mounting position
The device may overheat and therefore be damaged if mounted in an inadmissible position.
• Only operate the device in admissible mounting positions.
Fundamental safety instructions
1.1 General safety instructions
ONE MCP Part 2: MCP 2400
Equipment Manual, 07/2020, A5E50324707B AA 7
WARNING
Unexpected movement of machines caused by inactive safety functions
Inactive or non-adapted safety functions can trigger unexpected machine movements that
may result in serious injury or death.
• Observe the information in the appropriate product documentation before commissioning.
• Carry out a safety inspection for functions relevant to safety on the entire system, including
all safety-related components.
• Ensure that the safety functions used in your drives and automation tasks are adjusted and
activated through appropriate parameterizing.
• Perform a function test.
• Only put your plant into live operation once you have guaranteed that the functions
relevant to safety are running correctly.
Note
Important safety notices for Safety Integrated functions
If you want to use Safety Integrated functions, you must observe the safety notices in the Safety
Integrated manuals.
1.2 Equipment damage due to electric elds or electrostatic discharge
Electrostatic sensitive devices (ESD) are individual components, integrated circuits, modules or
devices that may be damaged by either electric elds or electrostatic discharge.
NOTICE
Equipment damage due to electric elds or electrostatic discharge
Electric elds or electrostatic discharge can cause malfunctions through damaged individual
components, integrated circuits, modules or devices.
• Only pack, store, transport and send electronic components, modules or devices in their
original packaging or in other suitable materials, e.g conductive foam rubber of aluminum
foil.
• Only touch components, modules and devices when you are grounded by one of the
following methods:
– Wearing an ESD wrist strap
– Wearing ESD shoes or ESD grounding straps in ESD areas with conductive ooring
• Only place electronic components, modules or devices on conductive surfaces (table with
ESD surface, conductive ESD foam, ESD packaging, ESD transport container).
Fundamental safety instructions
1.2 Equipment damage due to electric elds or electrostatic discharge
ONE MCP Part 2: MCP 2400
8Equipment Manual, 07/2020, A5E50324707B AA
1.3 Warranty and liability for application examples
Application examples are not binding and do not claim to be complete regarding conguration,
equipment or any eventuality which may arise. Application examples do not represent specic
customer solutions, but are only intended to provide support for typical tasks.
As the user you yourself are responsible for ensuring that the products described are operated
correctly. Application examples do not relieve you of your responsibility for safe handling when
using, installing, operating and maintaining the equipment.
1.4 Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is necessary
to implement – and continuously maintain – a holistic, state-of-the-art industrial security
concept. Siemens’ products and solutions constitute one element of such a concept.
Customers are responsible for preventing unauthorized access to their plants, systems,
machines and networks. Such systems, machines and components should only be connected to
an enterprise network or the internet if and to the extent such a connection is necessary and only
when appropriate security measures (e.g. rewalls and/or network segmentation) are in place.
For additional information on industrial security measures that may be implemented, please
visit
https://www.siemens.com/industrialsecurity (https://www.siemens.com/industrialsecurity).
Siemens’ products and solutions undergo continuous development to make them more secure.
Siemens strongly recommends that product updates are applied as soon as they are available
and that the latest product versions are used. Use of product versions that are no longer
supported, and failure to apply the latest updates may increase customer’s exposure to cyber
threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS Feed
under
https://www.siemens.com/industrialsecurity (https://new.siemens.com/global/en/products/
services/cert.html#Subscriptions).
Further information is provided on the Internet:
Fundamental safety instructions
1.4 Security information
ONE MCP Part 2: MCP 2400
Equipment Manual, 07/2020, A5E50324707B AA 9
Industrial Security Conguration Manual (https://support.industry.siemens.com/cs/ww/en/
view/108862708)
WARNING
Unsafe operating states resulting from software manipulation
Software manipulations, e.g. viruses, Trojans, or worms, can cause unsafe operating states in
your system that may lead to death, serious injury, and property damage.
• Keep the software up to date.
• Incorporate the automation and drive components into a holistic, state-of-the-art industrial
security concept for the installation or machine.
• Make sure that you include all installed products into the holistic industrial security concept.
• Protect les stored on exchangeable storage media from malicious software by with suitable
protection measures, e.g. virus scanners.
• On completion of commissioning, check all security-related settings.
1.5 Residual risks of power drive systems
When assessing the machine- or system-related risk in accordance with the respective local
regulations (e.g., EC Machinery Directive), the machine manufacturer or system installer must
take into account the following residual risks emanating from the control and drive components
of a drive system:
1. Unintentional movements of driven machine or system components during commissioning,
operation, maintenance, and repairs caused by, for example,
– Hardware and/or software errors in the sensors, control system, actuators, and cables and
connections
– Response times of the control system and of the drive
– Operation and/or environmental conditions outside the specication
– Condensation/conductive contamination
– Parameterization, programming, cabling, and installation errors
– Use of wireless devices/mobile phones in the immediate vicinity of electronic components
– External inuences/damage
– X-ray, ionizing radiation and cosmic radiation
2. Unusually high temperatures, including open ames, as well as emissions of light, noise,
particles, gases, etc., can occur inside and outside the components under fault conditions
caused by, for example:
– Component failure
– Software errors
– Operation and/or environmental conditions outside the specication
– External inuences/damage
Fundamental safety instructions
1.5 Residual risks of power drive systems
ONE MCP Part 2: MCP 2400
10 Equipment Manual, 07/2020, A5E50324707B AA
Altri manuali per SINUMERIK ONE MCP 2400
1
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Siemens Pannello di controllo
Siemens
Siemens CP-2ER Manuale di istruzioni
Siemens
Siemens simatic hmi op27 Documento tecnico
Siemens
Siemens FS720 Series Manuale utente
Siemens
Siemens SINAMICS Intelligent Operator Panel Manuale utente
Siemens
Siemens SINUMERIK 840D sl Documento tecnico
Siemens
Siemens Series 2300 Manuale utente
Siemens
Siemens SINAMICS G130 Manuale utente
Siemens
Siemens SIMATIC HMI KTP700F Mobile Manuale utente
Siemens
Siemens P5 Manuale utente
Siemens
Siemens FC2025 Manuale utente
Siemens
Siemens FC361 Series Manuale utente
Siemens
Siemens OP1S Manuale utente
Siemens
Siemens SIMATIC HMI KP300 Basic mono PN Manuale utente
Siemens
Siemens SIMATIC HMI 177 Manuale utente
Siemens
Siemens FIREFINDER-XLS Manuale utente
Siemens
Siemens SUT50 Manuale utente
Siemens
Siemens SINAMICS BOP-2 Manuale utente
Siemens
Siemens SIMATIC Mobile Panel 277 IWLAN Guida utente
Siemens
Siemens SIMATIC HMI KTP400 Basic Manuale utente
Siemens
Siemens 3RA6935-0A Manuale utente
