Siemens Powermite 599 Series Manuale del proprietario
Powermite 599 Series
Technical Instructions
Document No. 155-314P25
EA 599-16
May 24, 2005
MT Series SSC Electronic
Valve Actuator, 24 Vac
3-Position (Floating) Control
EA1157R1
Description The Powermite 599 Series MT Series SSC81U and SSC81.5U electronic valve
actuators require a 24 Vac supply to provide a 3-position (floating) control signal. These
actuators control Powermite 599 MT Series valves with a 7/32-inch (5.5 mm) stroke
and a threaded valve bonnet that fits the actuators.
Features • UL listed for plenum installations
• Direct coupled installation without special tools
• Manual override
• Visual position indication
Application The Powermite 599 Series MT Series SSC81… electronic actuators and MT Series
valves are used in heating and cooling applications. They are used in liquid and steam
applications that require an actuator that delivers a minimum of 67 lbs (300 N) nominal
force. The SSC81 series accepts plenum cable or 3/8-inch flex conduit connection.
Product Numbers Table 1. Product Numbers.
Actuator Operating Mode
Actuator Prefix
Code
SSC81U Fail-in-Place 259
SSC81.5U Fail-Safe 260
Ordering a Valve
Plus Actuator
Assembly
To order a complete valve plus actuator assembly from the factory, combine the
actuator prefix code with the suffix of the valve product number. See Technical Bulletin
TB251, Powermite 599 Series MT Series Terminal Unit Valve and Actuator Assembly
Selection (155-306P25) for selection procedures.
To order an actuator only, use the product number.
Siemens Building Technologies, Inc.
Technical Instructions MT Series SSC Electronic Valve Actuator, 24 Vac 3-Position (Floating) Control
Document Number 155-314P25
May 24, 2005
Specifications
Power requirements
Operating voltage 24 Vac ±20%
Frequency 50/60 Hz ±2 Hz
Power supply Earth ground isolating Class 2,
24 Vac transformer
NOTE: Do not power more than
10 actuators with one
transformer.
SSC81U power consumption 0.8 VA
SSC81.5U power consumption 3 VA at ultra cap load,
2 VA at normal drift
Control characteristic Control Signal
Y2 Retracts actuator shaft
Y1 Extends actuator shaft
G System potential
G0 (SSC81.5U only) System neutral
Functional operation Running time
SSC81U 150 s ±2% at 50 Hz
125 s ±2% at 60 Hz
SSC81.5U 125 s ±2% at 50/60 Hz
Fail-safe, SSC81.5U only (Figure 1, ) ≈30 s
Nominal stroke 7/32-inch (5.5 mm)
Nominal force 67 lb (300N), +20%, -0%
Stroke/signal relationship Linear
Capacitor charge time (Figure 1 ) max. 180 sec
Fail-safe (SSC81.5U only) Non-mechanical, electronic return fails
to stem up (0 position)
Agency certification UL UL873 Listed
cUL Certified to Canadian Standard
C22.2 No. 24-93
Ambient conditions Ambient temperature
Operation 41°F to 122°F (5°C to 50°C) with
15 psi steam media
Transport and storage -13°F to 158°F (-25°C to +70°C)
Ambient humidity 0 to 90% rh (non-condensing)
Medium temperature 41°F to 248°F (5°C to 120°C)
Physical characteristics Wiring Connection Plenum cable or 3/8-inch flex conduit
Weight
SSC81U 1.1 lb (0.5 kg)
SSC81.5U 1.3 lb (0.6 kg)
Dimensions See Figure 8
Page 2 Siemens Building Technologies, Inc.
MT Series SSC Electronic Valve Actuator, 24 Vac 3-Position (Floating) Control Technical Instructions
Document Number 155-314P25
May 24, 2005
Service Kits
EA0847R1
3mm
4 224 5618 8 Visual Position Kit to
replace one indicator and two gears.
(Previous version.)
EA1156R1
EA1162R1
EA0851R1
EA1138R1
EA1138R1
EA1138R1
4-115-5564-8: Kit contains:
- Terminal cover
- Cover screws-2 (not shown)
- Tailpiece
- Tailpiece screw-1 (not shown)
- Cable lock
- Terminal block-3
EA0850R1
EA0851R1
4-116-5608-8: Kit contains:
- Terminal Cover
- Cable lock
- Cover screw- 1 (not shown)
Operation A 24 Vac control signal to terminal Y1 extends the actuator shaft proportionately to the
length of time the signal is applied.
A 24 Vac control signal to terminal Y2 retracts the actuator shaft proportionately to the
length of time the signal is applied.
In the event of a power failure with no control voltage, the SSC81U fails-in-place and
holds its last position.
In the event of a power failure, the SSC81.5U returns to its normal fail-safe position.
The SSC81.5U includes an electronic return mechanism that functions as follows. See
Figure 1.
• At power-up (t0), a capacitor must
charge to its maximum capacity
(Max, tc). This will take a maximum
of 180 sec, during which time no
actuator movement occurs.
• Once the capacitor is fully charged
(tc), normal actuator operation
occurs.
• If a subsequent power failure occurs
(tn) of greater than 5 sec, the
capacitor discharges (td) and the
actuator returns to its normal fail-safe
position.
EA0798R2
TIME
MAX
180s. MAX
30s.
CHARGE
Max
0
NORMAL
ACTUATOR
OPERATION
ACTUATOR
POSITION
TIME TO
DISCHARGE
TIME TO
CHARGE
t0 tctntd
Figure 1. SSC81.5U Electronic Fail-Safe
Mechanism.
Siemens Building Technologies, Inc. Page 3
Technical Instructions MT Series SSC Electronic Valve Actuator, 24 Vac 3-Position (Floating) Control
Document Number 155-314P25
May 24, 2005
Operation, Continued
CAUTION:
Before applying power, make certain a valve is connected to the
actuator.
If applying power to the actuator when a valve is not connected, the
actuator will respond to a control signal and the shaft will extend until it
reaches its maximum end stop. Thereafter, it will not respond to any
signal.
If this occurs, turn the manual position indicator (See Figure 6 and
Figure 7)on the top of the actuator to the 0 position and verify the
actuator shaft retracts completely. Disconnect power. Connect a valve
to the actuator, reapply power, and the actuator will return to normal
operation.
Calibration Stroke The SSC81.5U writes its calibration stroke parameters to nonvolatile memory on the
first startup of the actuator. Successive startups bypass the calibration stroke unless the
memory is manually cleared. If installing the actuator on a different valve (such as on a
replacement valve), manually clear the calibration stroke from memory as follows:
1. Remove the terminal cover using a Phillips
head screwdriver.
2. Locate hole on the circuit board shorting
bars.
3. Insert and gently twist a flat-blade
screwdriver to electrically connect the
shorting bars (Figure 2). The SSC81…
then performs a new calibration stroke.
4. Secure the terminal cover back in place.
EA1155R1
WIRINGTERMINAL
WITH REMOVABLE
TERMINAL BLOCK
Shorting
Bars
TERMINAL
COVER
AND SCREWS
Figure 2. Manually Clearing Calibration
Stroke from Memory.
Mounting and
Installation Mount the actuator in one of the allowable positions shown in Figure 3.
EA0791R2
Figure 3. Mounting Position.
When mounting the actuator in a plenum, the proper cable must be attached to meet
local codes. Allow 8 inches (200 mm) above the actuator and 8 inches (200 mm) behind
the cable for service.
Page 4 Siemens Building Technologies, Inc.
MT Series SSC Electronic Valve Actuator, 24 Vac 3-Position (Floating) Control Technical Instructions
Document Number 155-314P25
May 24, 2005
Wiring Use earth ground isolating step-down Class 2 transformers. Do not use
autotransformers.
Determine supply transformer rating by summing total VA of all actuators used. The
maximum rating for a Class 2 step-down transformer is 100 VA.
Do not power more than 10 actuators by one transformer.
CAUTION:
Terminals must be properly wired for correct function and full life of the
actuator.
Wiring Diagrams
NEUT
CONTROLLER ACTUATOR
EARTH GROUND
ISOLATING CLASS 2
TRANSFORMER FOR
24 Vac POWER
120 Vac
Y2
Y1
G
24
Vac
EA0795R1
Y2…Retracts actuator shaft
Y1…Extends actuator shaft
G…System potential
Figure 4. SSC81U (Fail-in-Place)
Wiring.
EA0796R3
NEUT
CONTROLLER
EARTH GROUND
ISOLATING CLASS 2
24VacTRANSFORMER
120Vac
24Vac
ACTUATOR
G
Y2
Y1
G0
1
0
0
Y2…Retracts actuator shaft
Y1…Extends actuator shaft
G… System potential
G0…System neutral
Figure 5. SSC81.5U (Fail-Safe) Wiring.
Manual Override For manual positioning, the manual
override knob in the center of the position
indicator per Figure 6.
CLOCKWISE
EXTENDS
SHAFT
COUNTER
CLOCKWISE
RETRACTS
SHAFT
EA1161R1
A
B
AB
Figure 6. Manual Override.
1
0
Siemens Building Technologies, Inc. Page 5
Technical Instructions MT Series SSC Electronic Valve Actuator, 24 Vac 3-Position (Floating) Control
Document Number 155-314P25
May 24, 2005
Start-up Check the wiring and the position indicator
(Figure 7).
Position Indicator Output Shaft
0 Retracted
1 Extended
0
1
EA1158R1
Figure 7. Position Indicator
(Shown in 0 Position).
Troubleshooting Check the wiring for proper connections.
Service Kits If the actuator is inoperative, replace the unit.
Dimensions
2
(48)
4.4
(110,8)
3.5
(89)
.85
(21,6)
4.5
(115,1) 5.5
(140)
EA1159R1
0
1
Figure 8. SSC Actuator Dimensions in Inches (Millimeters).
Service envelope Minimum access space recommended:
8 inches (200 mm) above the actuator and beside the terminal cover.
Information in this publication is based on current specifications. The company reserves the right to make changes in specifications and models as
design improvements are introduced. Other product or company names mentioned herein may be the trademarks of their respective owners.
© 2005 Siemens Building Technologies, Inc.
Siemens Building Technologies, Inc.
1000 Deerfield Parkway Your feedback is important to us. If you have
comments about this document, please send
Buffalo Grove, IL 60089-4513
Document No. 155-314P25
Country of Origin: US
Altri manuali per Powermite 599 Series
3
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali Siemens Controllori
Siemens
Siemens i-3 Manuale utente
Siemens
Siemens SIDOOR AT40 Guida utente
Siemens
Siemens Simatic S7-300 Manuale utente
Siemens
Siemens SIMATIC S5 CPU Direct Driver Manuale utente
Siemens
Siemens SAS61.33U Manuale del proprietario
Siemens
Siemens CLIMATIX C400 Manuale utente
Siemens
Siemens SIMOTION Series Manuale utente
Siemens
Siemens N 605D41 Manuale utente
Siemens
Siemens Flowrite 599 Series Manuale utente
Siemens
Siemens SINAMICS G130 Manuale utente
Siemens
Siemens GDB 1 Series Manuale utente
Siemens
Siemens SIPART DR21 Manuale utente
Siemens
Siemens QAA75 series Manuale utente
Siemens
Siemens OpenAir G B181.1E/3 Series Guida all'installazione
Siemens
Siemens SKP Series Manuale del proprietario
Siemens
Siemens GIB 1 Series Manuale utente
Siemens
Siemens GBB 2 Series Manuale utente
Siemens
Siemens SITRANS S7-300 Manuale utente
Siemens
Siemens SIMATIC EM 300 Manuale utente
Siemens
Siemens SIRIUS 3SX5100-2F Manuale utente
