Siemens SIMATIC S7-200 Manuale utente
1
Siemens AG
Ethernet Gateway
for SIMATIC MPI/
PROFIBUS Driver
1 System Configuration....................................................................................................... 3
2 External Device Selection ................................................................................................ 6
3 Communication Settings .................................................................................................. 7
4 Setup Items ...................................................................................................................... 9
5 Supported Device Addresses......................................................................................... 15
6 Device Code and Address Code.................................................................................... 17
7 Error Messages.............................................................................................................. 18
Ethernet Gateway for SIMATIC MPI/PROFIBUS Driver
GP-Pro EX Device/PLC Connection Manual 2
Introduction
This manual describes how to connect the Display and the External Device (target PLC).
In this manual, the connection procedure is described in the sections identified below:
1System Configuration
This section lists the types of External
Devices and SIO that you can connect.
"1 System Configuration" (page 3)
2External Device Selection
Select the model (series) of the External
Device and its connection method.
"2 External Device Selection" (page 6)
3Communication Settings
This section shows setting examples for
communicating between the Display and
the External Device.
"3 Communication Settings" (page 7)
4Setup Items
This section describes communication
setup items on the Display.
Set the Display's communication settings
in GP Pro-EX or in off-line mode.
"4 Setup Items" (page 9)
Operation
Ethernet Gateway for SIMATIC MPI/PROFIBUS Driver
GP-Pro EX Device/PLC Connection Manual 3
1 System Configuration
The system configuration in the case when the External Device of Siemens AG and the Display are connected is
shown.
Series CPU Link I/F Communication
Method Setting Example
SIMATIC
S7-200 Series
CPU214
CPU215
CPU216
CPU221
CPU222
CPU224
CPU226
Port 0/1 on the CPU unit Ethernet (TCP) "Setting Example 1"
(page 7)
SIMATIC
S7-300 Series
CPU312IFM
CPU313
CPU314
CPU314IFM
CPU315
CPU315-2 DP
CPU316
CPU316-2 DP
CPU318-2
MPI port on the CPU
unit Ethernet (TCP) "Setting Example 1"
(page 7)
SIMATIC
S7-400 Series
CPU412-1
CPU412-2 DP
CPU413-1
CPU413-2 DP
CPU414-1
CPU414-2 DP
CPU414-3 DP
CPU416-1
CPU416-2 DP
CPU416-3 DP
CPU417-4
MPI port on the CPU
unit Ethernet (TCP) "Setting Example 1"
(page 7)
Ethernet Gateway for SIMATIC MPI/PROFIBUS Driver
GP-Pro EX Device/PLC Connection Manual 4
Connection Configuration
1:1 Connection
1:n Connection
or
Display External Device
Adapter
Display External Device External Device
Adapter
Maximum number of External Devices: 12
Display External Device External Device
Adapter
HUB
Maximum number of External Devices: 12
Ethernet Gateway for SIMATIC MPI/PROFIBUS Driver
GP-Pro EX Device/PLC Connection Manual 5
n:m Connection
or
• It is able to connect only one adapter to one Display.
Display External Device
Display External Device
Adapter
Adapter
HUB
Maximum Display Units depends
on the External Device CPU Maximum number of Display: 12
Display External Device
Display External Device
Adapter
HUB
Maximum number of Display: 7 Maximum number of Display: 12
Ethernet Gateway for SIMATIC MPI/PROFIBUS Driver
GP-Pro EX Device/PLC Connection Manual 6
2 External Device Selection
Select the External Device to be connected to the Display.
Setup Items Setup Description
Number of Devices/PLCs Use an integer from 1 to 4 to enter the number of Devices/PLCs to connect to the
display.
Manufacturer Select the manufacturer of the External Device to be connected. Select "Siemens
AG".
Series
Select a model (series) of the External Device to be connected and connection
method. Select "Ethernet Gateway for SIMATIC MPI/PROFIBUS".
Check the External Device which can be connected in "Ethernet Gateway for
SIMATIC MPI/PROFIBUS" in system configuration.
"1 System Configuration" (page 3)
Port Select the Display port to be connected to the External Device. Select "Ethernet
(TCP)".
Use System Area
Check this option to synchronize the system data area of the Display and the device
(memory) of the External Device. When synchronized, you can use the External
Device’s ladder program to switch the display or display the window on the Display.
Cf. GP-Pro EX Reference Manual "LS Area (Direct Access Method
Area)"
This feature can also be set in GP-Pro EX or in the Display's offline mode.
Cf. GP-Pro EX Reference Manual "System Settings [Display Unit] -
[System Area] Settings Guide"
Cf. Maintenance/Troubleshooting Guide "Main Unit - System Area
Settings"
Ethernet Gateway for SIMATIC MPI/PROFIBUS Driver
GP-Pro EX Device/PLC Connection Manual 7
3 Communication Settings
This section provides examples of communication settings recommended by Pro-face for the Display and the
External Device.
3.1 Setting Example 1
GP-Pro EX Settings
Communication Settings
To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC].
Ethernet Gateway for SIMATIC MPI/PROFIBUS Driver
GP-Pro EX Device/PLC Connection Manual 8
Device Setting
To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC]
window, select the external device and click [Settings] .
To connect multiple External Devices, from [Device-Specific Settings] in the [Device/PLC] window, click [Add
Device] to add another External Device.
External Device Settings
Use the Web Browser to access the Adapter for communication setting. Please refer to the manual of the Adapter
for more details.
1The home page, which is located at ‘http://<ip-address>’, is a basic address and navigation starting point for the
user.
2The configuration page, accessible via a link on the home page, is a configuration interface for the user.
Before this page opens, it is necessary to enter the device name as Username (NETLink PRO) and the password
(admin if no user specified password is stored). The default password is ‘admin’.
3Enter the following settings and click [OK].
If you click the [OK] button, the inputs are checked for plausibility. You may then be shown which inputs are
incorrect and what correct input would look like at this point.
4If all entries are consistent, the changes are displayed again as they will now be stored in the adapter when you
click the 'OK' button again.
After the new parameters have been stored, the adapter is restarted to activate the new configuration.
• At delivery state the Adapter has the IP address 192.168.4.49
Setup Items Setting
Device name Name assigned to the adapter consisting of max. 20 alphanumeric characters.
Static IP address IP address that is used if DHCP is deactivated or the DHCP timeout elapses
Static subnet mask Subnet mask that is used if DHCP is deactivated or the DHCP timeout elapses
DHCP ON/OFF activate DHCP
DHCP Timeout
(seconds) 30 to 65500 seconds
Web interface ON/
OFF Web interface is ON or OFF
RFC1006 parameters not needed for communication with GP-Pro EX applications
New passwords password with up to eight characters
Ethernet Gateway for SIMATIC MPI/PROFIBUS Driver
GP-Pro EX Device/PLC Connection Manual 9
4 Setup Items
Set up the Display's communication settings in GP Pro-EX or in the Display's off-line mode.
The setting of each parameter must match that of the External Device.
"3 Communication Settings" (page 7)
4.1 GP-Pro EX Setup Items
Communication Settings
To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC].
Setup Items Setup Description
Port No. Enter a port number of the Display, using 1024 to 65535. Check into [Auto], and a port
number is set automatically.
Timeout Use an integer from 1 to 127 to enter the time (s) for which Display waits for the response
from External Device.
Retry In case of no response from the External Device, use an integer from 0 to 255 to enter how
many times the Display retransmits the command.
Wait To Send Use an integer from 0 to 255 to enter standby time (ms) for the Display from receiving
packets to transmitting next commands.
Ethernet Gateway for SIMATIC MPI/PROFIBUS Driver
GP-Pro EX Device/PLC Connection Manual 10
IP Address
Input the IP address of Gateway/Module. Search the adapter in the network and click the
[Search].
Port No. Display the port number of Gateway/Module.
Speed Set the communication speed of MPI/PROFIBUS network.
Local Node Set the node number of Display in MPI/PROFIBUS network.
Highest Node Number Set the maximum node number of MPI/PROFIBUS network.
• Refer to the GP-Pro EX Reference Manual for Indirect Device.
Cf. GP-Pro EX Reference Manual "Changing the Device/PLC at Runtime (Indirect
Device)"
Setup Items Setup Description
Altri manuali per SIMATIC S7-200
11
Questo manuale è adatto per i seguenti modelli
29
Indice
Altri manuali Siemens Portale
Siemens
Siemens SIMATIC IOT Manuale utente
Siemens
Siemens VersiComm VC1COMMA Manuale utente
Siemens
Siemens Gigaset SE568 Manuale utente
Siemens
Siemens SIMATIC RTLS Series Guida all'applicazione
Siemens
Siemens SIMATIC Manuale utente
Siemens
Siemens SIMATIC RTLS Series Guida all'applicazione
Siemens
Siemens MindConnect Nano Manuale utente
Siemens
Siemens SIMATIC FDE Documento tecnico
Siemens
Siemens SIMATIC IOT Gateway MQTT Guida utente
Siemens
Siemens DESIGO RXC Manuale utente
Siemens
Siemens SpeedStream 6500 Series Manuale utente
Siemens
Siemens SCALANCE X-300 Guida
Siemens
Siemens MindConnect Nano Manuale utente
Siemens
Siemens NK8237 MP4.81-01 Manuale utente
Siemens
Siemens OCT200.KNBA Manuale utente
Siemens
Siemens SCALANCE X-200 Manuale utente
Siemens
Siemens 5WG1 141-1AB31 Manuale di servizio
Siemens
Siemens 5WG1143-1AB01 Manuale utente
Siemens
Siemens SpeedStream 6500 Series Manuale utente
Siemens
Siemens Gigaset Optical LAN Adapter Duo Manuale utente
Manuali Portale popolari di altre marche
LST
LST M500RFE-AS Manuale utente
Kinnex
Kinnex Media Gateway Manuale utente
2N Telekomunikace
2N Telekomunikace 2N StarGate Manuale utente
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuale utente
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manuale utente
Telsey
Telsey CPVA 500 - SIP Manuale utente
