Siemens SIMATIC NET PS598-1 Guida per l'amministratore

A5E03275848-04, 05/2013 1

Legal information

Qualified Personnel

The product/system described in this documentation may be operated only by personnel

qualified for the specific task in accordance with the relevant documentation, in particular its

warning notices and safety instructions. Qualified personnel are those who, based on their

training and experience, are capable of identifying risks and avoiding potential hazards when

working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the

relevant technical documentation. If products and components from other manufacturers are

used, these must be recommended or approved by Siemens. Proper transport, storage,

installation, assembly, commissioning, operation and maintenance are required to ensure that

the products operate safely and without any problems. The permissible ambient conditions

must be complied with. The information in the relevant documentation must be observed.

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as

well as to prevent damage to property. The notices referring to your personal safety are

highlighted in the manual by a safety alert symbol, notices referring only to property damage

have no safety alert symbol. These notices shown below are graded according to the degree of

danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest

degree of danger will be used. A notice warning of injury to persons with a safety alert symbol

may also include a warning relating to property damage.

Power supply unit PS598-1 for SCALANCE XR500

2A5E03275848-04, 05/2013

Table of contents

1 Introduction..................................................................................................3

2 Safety notes.................................................................................................3

3 Description...................................................................................................4

3.1 Product characteristics ......................................................................... 4

3.2 Unpacking and checking ...................................................................... 5

4 Mounting......................................................................................................6

4.1 19" rack mounting of the PS598-1........................................................ 6

4.2 Mounting the PS598-1 on the rear panel of an XR500......................... 8

5 Connection ................................................................................................11

5.1 Connecting devices with 100 to 240 VAC power supply .................... 11

5.2 LED display ........................................................................................ 16

6 Upkeep and maintenance...........................................................................17

7 Technical data............................................................................................18

8 Dimension drawings ...................................................................................19

9 Approvals...................................................................................................20

9.1 EMC directive ..................................................................................... 20

9.2 Mechanical stability (in operation) ...................................................... 22

Power supply unit PS598-1 for SCALANCE XR500

A5E03275848-04, 05/2013 3

1 Introduction

Purpose of the compact operating instructions

Based on the compact operating instructions, you will be able to install and connect

up the PS598-1 correctly.

Validity of these compact operating instructions

These compact operating instructions apply to the product PS598-1 as of product

version 1.

2 Safety notes

Safety notices on the use of the devices

The following safety notices must be adhered to when setting up and operating the

device and during all work relating to it such as installation, connecting up, replacing

devices or opening the device.

Important notices 100 to 240 VAC

DANGER

Danger from line voltage

Devices with this mark have a 100 to 240 VAC power supply.

This product can only function correctly and safely if it is transported, stored, set up,

and installed correctly, and operated and maintained as recommended.

Connecting and disconnecting may only be performed by an electrical specialist.

Connect or disconnect power supply cables only when the power is turned off!

General notices

WARNING

Opening the device

Do not open when energized. Note that this does not apply to opening the panel in

the housing.

Power supply unit PS598-1 for SCALANCE XR500

4A5E03275848-04, 05/2013

3 Description

3.1 Product characteristics

Connectors

Type

Power

Input voltage

Output voltage

PS598-1

300 W

100 to 240 VAC

24 VDC

Note

Two connectors for the 24 VDC output voltage

The PS598-1 has two connectors with the output voltage 24 VDC. Note that you can

only use one connector on the front or the connector on the rear of the PS598-1. You

cannot operate the device with the connectors on the front and rear at the same time.

Note

Requirement for connecting at the rear

Note that the connector on the rear of the PS598-1 can only be used if the power

supply is mounted on the SCALANCE XR500.

Components of the product

The following parts make up the components of the PS598-1:

●4-pin terminal block for the 24 VDC power supply.

●2 mounting brackets

●8 screws (M3 x 6 countersunk, drive: Torx) for mounting the fixing brackets for

19" rack installation

●Compact Operating Instructions

Description

Power supply unit PS598-1 for SCALANCE XR500

A5E03275848-04, 05/2013 5

Order numbers

Type

Order number

PS598-1 (300 W)

6GK5 598-1AA00-3AA0

Note

Replacing the filter mat

To replace the filter mat, use the material Viledon P 15/150 G2 EN 779. The

dimensions of the filter mat are 38 x 135 x 8 mm (H x W x D).

3.2 Unpacking and checking

WARNING

Do not use any parts that show evidence of damage

If you use damaged parts, there is no guarantee that the device will function

according to the specification.

If you use damaged parts, this can lead to the following problems:

●Injury to persons

●Loss of the approvals

●Violation of the EMC regulations

Use only undamaged parts.

1. Make sure that the package is complete.

2. Check all the parts for transport damage.

If the consignment is incomplete or if there is damage to the exterior, contact your

supplier or your local Siemens office.

Power supply unit PS598-1 for SCALANCE XR500

6A5E03275848-04, 05/2013

4 Mounting

4.1 19" rack mounting of the PS598-1

Power supply unit for 19" rack installation

The PS598-1 was developed specifically for use with devices of the XR500 product

group. This power supply unit can be mounted directly above or below a SCALANCE

XR500 since the ventilation grilles are on the sides of both the basic device and the

power supply unit.

CAUTION

Risk of injury if subjected to irregular mechanical strain

The device must be mounted in the rack so that even if there is irregular mechanical

strain, no dangerous situation can result.

NOTICE

Damage to the device due to inadequate cooling

If the ventilation grilles are fully or partly covered or the air filters are contaminated,

the temperature inside the housing can rise and exceed the maximum permitted

temperature and damage the device.

During installation, select a mounting position so that the ventilation grilles are

always free so that the air can circulate. The ventilation grilles are located on the

side panels of the housing. You will find information about cleaning the air filter in

the section "Upkeep and maintenance".

Mounting

Power supply unit PS598-1 for SCALANCE XR500

A5E03275848-04, 05/2013 7

Procedure

Follow the steps below to install the PS598-1 in a 19" rack:

1. Secure the two mounting brackets with four screws each (M3 x 6 supplied with

the product) to the side panels of the power supply unit. The maximum tightening

torque for these screws is 0.5 Nm.

2. Screw the PS598-1 to the 19" rack.

Mounting

Power supply unit PS598-1 for SCALANCE XR500

8A5E03275848-04, 05/2013

4.2 Mounting the PS598-1 on the rear panel of

an XR500

NOTICE

Damage to the device due to inadequate cooling

If the ventilation grilles are fully or partly covered or the air filters are contaminated,

the temperature inside the housing can rise and exceed the maximum permitted

temperature and damage the device.

During installation, select a mounting position so that the ventilation grilles are

always free so that the air can circulate. The ventilation grilles are located on the

side panels of the housing. You will find information about cleaning the air filter in

the section "Upkeep and maintenance".

Altri manuali per SIMATIC NET PS598-1

Indice

Altri manuali Siemens Alimentazione elettrica

Siemens

Siemens SITOP C98130-A1251-A1-02-19 Manuale utente

Siemens

Siemens FP1801-A2 Manuale utente

Siemens

Siemens 4AV Series Manuale utente

Siemens

Siemens JB 125C23 Manuale utente

Siemens

Siemens MPS-12 Manuale utente

Siemens

Siemens 6ES7138-7EA01-0AA0 Manuale utente

Siemens

Siemens SIMATIC NET PS598-1 Guida per l'amministratore

Siemens

Siemens SITOP Power 20 6EP1 536-2AA00 Manuale utente

Siemens

Siemens SAP 20 Manuale utente

Siemens

Siemens 7XV5810-0CA00 Manuale utente

Siemens

Siemens GAMMA N 125/02 Manuale di servizio

Siemens

Siemens SIPLUS PSU Manuale utente

Siemens

Siemens PSN130S Manuale utente

Siemens

Siemens SITOP PSU100M Manuale utente

Siemens

Siemens SITOP PSU6200 Manuale utente

Siemens

Siemens SITOP PSU300S Manuale utente

Siemens

Siemens SITOP PSU8600 Manuale utente

Siemens

Siemens MICROMASTER 440 Manuale utente

Siemens

Siemens 4AV2106-2EB00-0A Manuale utente

Siemens

Siemens SIMATIC NET PS598-1 Guida per l'amministratore

Siemens

Siemens SITOP PSU6200 3ph Documento tecnico

Siemens

Siemens SINAMICS S120 Istruzioni per l’uso

Siemens

Siemens SPCP355 Manuale utente

Siemens

Siemens PSC-12 Manuale utente

Manuali Alimentazione elettrica popolari di altre marche

Monacor

Monacor PS-12CCD Manuale utente

VOLTIMA

VOLTIMA MagicBox 15 Manuale utente

Agilent Technologies

Agilent Technologies 6032A Manuale utente

Miller

Miller Auto Deltaweld 452 Manuale utente

BCP

BCP PUOUBK Foglio di istruzioni

HC 2210 Manuale utente

Puls

Puls CT5.241 Manuale utente

OCZ

OCZ ZX1250W Manuale utente

iseg

iseg ECH 238 Manuale utente

Power

Power XXL A Series Manuale utente

Agilent Technologies

Agilent Technologies 6631B Manuale utente

Renogy

Renogy PHOENIX 300 Manuale utente

HP 6200B Manuale di servizio

Epson

Epson Stylus Scan 2500 Manuale operativo

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manuale utente

Puls

Puls MiniLine ML50.100 Manuale utente

Puls

Puls AS-Interface SLA4.100 Manuale utente

Kenwood

Kenwood PS-60 Manuale utente