Siemens Flange Mount Kit Manuale utente
DPD01156B Siemens Industry, Inc.
1
Flange Mount Kits for Frames FS4 to FS7
Mounting Instructions
General
Using the optional Flange Mounting Kit, you can mount your drive through the cabinet wall or similar surface
so that the control unit of the drive remains inside the cabinet.
The correct installation of the Flange Mounting Kit might affect the IP or UL protection class of the drive. If
your drive is protected according to Type12/IP54, or your drive is supplied with flange option at the factory,
you only need to install the collars, as instructed. However, the power module of a Type1/IP21-protected drive
will only become protected according to Type12/IP54 on the rear side (see figure below), if all parts of the
flange mounting kit are installed properly. The need for this has to be evaluated and these actions are
explained in this guide.
Figure 1. Example of the flange mounting.
BT9070
CABINET WALL
OR SIMILAR
CABINET
WALL OR
SIMILAR
REAR
TYPE 12/
IP54
IP00
FRONT
Siemens Industry, Inc. DPD01156B
2
Flange Mount - Frames FS4 - FS7
Figures 2. - 5. present the dimensions of the drives with the flange mount option. Figure 6. present the
dimensions of the opening and the drive outline with the flange.
Use the embossed holes or self-clinching nuts in the back plate when mounting the drive to ensure proper
sealing.
Figure 2. FS4, flange mount, dimensions.
152 (5.98)
15 (.59)
122 (4.80)
Ø7(.27)
285 (11.22) 24 (.94)
113 (4.44)
357 (14.05)
341 (13.42)
101.6 (4)
72.1 (2.83)
18.5 (.72)
32.8 (1.29)
39 (1.53)
77 (3.03)
190 (7.48)
134 (5.27)
128 (5.03)
186.9 (7.35)9 (.35)
BT11134
DPD01156B Siemens Industry, Inc.
3
Figure 3. FS5, flange mount, dimensions.
BT11132
Ø7(.27)
Ø7(.27)
436 (17.16)
454.1 (17.87)
262.5 (10.33)
145 (5.70)
144 (5.66)
150 (5.90)
169 (6.65)
9 (.35)
13 (.51) 382 (15.03) 24 (.94)
39 (1.53)
33 (1.29)
27,5 (1.08)
100 (3.93)
214 (8.42)
114 (4.48)
11.5 (.45)
72.2 (2.84)
145 (5.70)
101.9 (4.01)
12 (.47)
Siemens Industry, Inc. DPD01156B
4
Figure 4. FS6, flange mount, dimensions
DPD01156B Siemens Industry, Inc.
5
Figure 5. FS7, flange mount, dimensions
Siemens Industry, Inc. DPD01156B
6
Figure 6. Flange mount cutout and drive outline dimensions for FS4 to FS7.
Table 1. Flange mount cutout dimensions for FS4 to FS7 in mm (in).
Frame A B C D E
FS4 315 (12.40) 137 (5.39) 357 (14.05) 152 (5.98) 24 (.94)
FS5 408 (16.06) 152 (5.98) 454 (17.87) 169 (6.65) 23 (.90)
FS6 541 (21.29) 203 (7.99) 580 (22.83) 220 (8.66) 23 (.90)
FS7 655 (25.78) 240 (9.44) 680 (26.77) 286 (11.25) 13 (.51)
11136.emf
up
flange
cutout
outline
DPD01156B Siemens Industry, Inc.
7
Flange Mount Kit for Frame FS4
The kit consists of:
1. Top collar, (70CMR00281)
2. Bottom collar, (70CMR00280)
3. Side collars (2 pcs), (70CMR00282)
4. Internal fan, (70CPE00132, 70CPE00056) depends on the
control unit
5. Sealing plug (3 pcs), (70CMR00324)
Additionally:
• 8 screws size 4x16 (for the top and bottom collar mounting)
• 3 screws size 4x12 (for the side collar mounting)
• 2 screws size 3.5x10 (for the bottom collar mounting)
FS4 Flange Mounting
If your drive is the Type 1/IP21-protected and there is the risk that dust or other impurities in the cooling air
might end up inside the control unit, start the mounting with actions described in the steps 1 to 4.
If this is not needed, install the flange mounting kit proceeding directly to the step 5. Note, in this case the rear
will not be according to the Type 12/IP54.
9266.emf
M3.5x10
M4x12
M4x16
5
2
1
33
4
Siemens Industry, Inc. DPD01156B
8
1
Remove the cover of the drive.
Lift up the I/O protection plate.
The location of the internal fan
depends on the control unit.
If you have the control unit presented
in the upper picture, slide the internal
fan into the opening with the label
facing the cabling end of the drive.
If you have the control unit presented
in the lower picture, install the internal
fan with the label facing downwards.
11147.emf
11150.emf
DPD01156B Siemens Industry, Inc.
9
2Connect the power wire to the power
connector. The location of the power
connector depends on the control unit.
3Remove the main fan.
11148.emf
11149.emf
9289.emf
Siemens Industry, Inc. DPD01156B
10
4
Insert the three sealing plugs into
position where indicated.
Remount the main fan carefully,
checking its position.
5
Attach the side collars with three
screws size 4x12. The tightening
torque for the screws is 2 Nm (17.70
lbf-in).
Important! Do not yet screw the fourth
screw in the bottom right hole.
11151.emf
!
9287.emf
Altri manuali Siemens Rack e supporto
Siemens
Siemens CAB-MP Manuale utente
Siemens
Siemens Actavix ASK33 Manuale utente
Siemens
Siemens 3VL800-1250 Manuale utente
Siemens
Siemens SENTRON 3VL160 Manuale utente
Siemens
Siemens 8GK4 801-2KK13 Guida utente
Siemens
Siemens VNT-MP Manuale utente
Siemens
Siemens 8MF1 2GS30 Series Manuale utente
Siemens
Siemens 3KX3612-1B Manuale utente
Siemens
Siemens 8PQ9800-0AA18 Manuale utente
Siemens
Siemens SIMATIC IPC647D Manuale utente
Siemens
Siemens 3WL / 630A - 2000A Manuale utente
Siemens
Siemens SINAMICS DCM Istruzioni per il montaggio
Siemens
Siemens SIWAREX R Construction Elastomer Bearing Manuale utente
Siemens
Siemens 8PQ9801-0AA00 Manuale utente
Siemens
Siemens 8PQ9800-6AA24 Manuale utente
Siemens
Siemens 3WL Series Manuale utente
Siemens
Siemens 8PQ9802-7AA11 Manuale utente
Siemens
Siemens 8PQ9801-7AA21 Manuale utente
Siemens
Siemens ASK77.5 Manuale utente
Siemens
Siemens MXL Series Istruzioni per il montaggio
