Siemens RDH10RF Manuale utente

123

Installation Instructions for the Siemens RF

receiver s

Technical Helpline: 0870 850 0184

Wiring Diagram

Legend

LX = Common

L1 = Live feed to

item to be

controlled

L2 = Changeover

contact

L = Live

N = Neutral

Terminals

Item to be controlled

12 3

4 5 6

Press and release LEARN button

on the back of the transmitter

To test transmission press TEST on the

transmitter

This will switch relay on in receiver irrespective

of temperature

RF TEST appears in transmitter display. To switch

test off press TEST again

Configuration Instructions for the Siemens RF

units

Press and release SET button, this

puts the receiver into learn mode

Good signal is indicated by the LED

flashing green, then solid

No signal is indicated by the LED

flashing red,then solid

Orange LED indicates relay is on Pressing the RESET button for about 4

seconds will erase all ID codes in the

receiver. The set up procedure has to

be repeated to regain communication

Note: The transmitter and receiver are supplied in a single box already configured. This

procedure only needs to be followed in case of communication issues

PKGPT01027A

230

VOLT

-RF

ER. R

R10

433

BOILER

TERMINAL BLOCK

REMOVE LINK - Marked

(TO EXTERNALCONTROLS)

CONNECT AS SHOWN

NOTE, LX, L1 & L2 ARE

‘VOLTS FREE’ CONTACTS.

SIEMENS

230

VOLT

230 VOLT, SWITCH LIVE

TO BOILER OR VALVE

DH/RDJ- RF/RECEIVER.

CR10/433

WIRE

LINK

L - LX

NOTE, LX, L1 & L2 ARE VOLTS FREE CONTACTS.

TO SWITCH, 230VOLT MAINS LIVE ON L1, PUT LINK BETWEEN L & LX

LCD Display

Guide to symbols

On LCD Display

Actual room temperature in °C

The selected temperature

Indicates there is a call for heat

Indication of low battery life, this signifies batteries must be replaced

How to use your Siemens RDH10/RDH10RF

Digital Room Thermostat This leaflet gives you easy to follow instructions on how to use your RDH10 digital room thermostat.

Technical Helpline: 0870 850 0184

Rotary Dial

How do I set the required temperature?

Turn the rotary dial to the left to decrease the

required temperature, or to the right to increase the

required temperature.

The required temperature is displayed next to the

following symbol

Batteries Compartment

The RESET button on the back of the controller can be pressed to return the controller

to the factory settings

PKGPT01020A

CE1N3070en

20.11.2007 Building Technologies

3070

Wireless room

temperature controller

with large LCD RDH10RF/SET

Non-programmable, for heating or cooling systems

•Large LCD

•Battery-powered: 2 x alkaline type AA batteries, 1.5 V

•RCR10/433 receiver

Use

The RDH10RF is used to control the room temperature in heating or cooling systems.

Typical applications:

•Homes

•Residential buildings

•Schools

•Offices

The controller is used together with the following equipment:

•Thermal valves or zone valves

•Combi boilers

•Gas or oil burners

•Fans

•Pumps

2/10

Siemens Room temperature controllers CE1N3070en

Building Technologies 20.11.2007

Functions

The controller acquires the room temperature with its integrated sensor.

Q14

T[°C]

OFF W

3031D01

T Room temperature

SD Switching differential

W Room temperature setpoint

L1 Output signal for heating

T[°C]

OFF

3011D02

T Room temperature

SD Switching differential

W Room temperature setpoint

L1 Output signal for cooling

The RDH10RF provides room temperature control only.

The digital display shows the actual room temperature and the comfort temperature

setpoint. When the heating output is active, the triangle symbol appears.

When taking out the batteries, the setpoints and the information required for operating

mode changeover are retained for maximum 2 minutes.

Ordering

When ordering, please give name and product number: Room temperature controller

RDH10RF/SET.

Valves and actuators are to be ordered as separate items.

Equipment combinations

Type of unit Product number Data sheet

Electromotoric actuator SFA21... 4863

Electrothermal actuator (for radiator valves) STA21... 4877

Electrothermal actuator (for small valves 2.5 mm) STP21... 4878

2- or 3-port zone valve MXI/MVI421… 4867

Electromotoric actuator for zone valves V..146.. SUA21 4830

Electric actuator SUA11/22 4832

Air damper actuator GDB… 4624

Air damper actuator GSD/GQD… 4606

Air damper actuator GXD… 4622

Function diagram

Temperature sensor

Display

Backup

3/10

Siemens Room temperature controllers CE1N3070en

Building Technologies 20.11.2007

Mechanical design

The controller consists of 4 parts:

•Plastic housing with digital display accommodating the electronics, operating ele-

ments and built-in room temperature sensor

•Baseplate (mounting base)

•Removable battery compartment

•Fold-out stand

The housing engages in the baseplate and snaps on. The baseplate carries the screw

terminals. There is a reset button on the rear of the unit.

1 Display of the room temperature in °C

2 Indicates a request for heat

3 Temperature setting knob

4 Battery compartment

5 Comfort temperature setpoint

6 RF

TEST Indicates RF signal test

7 Indicates low battery power; replace batteries

Key

4/10

Siemens Room temperature controllers CE1N3070en

Building Technologies 20.11.2007

Mechanical design

The RCR10/433 receiver is located in a plastic housing with LEDs and buttons.

1 LED signal indicator

2 LED relay indicator

3 SET button

4 RESET button

5 Test button

6 Learn button

Notes

Mount the room temperature controller in a location where the air temperature can be

acquired as accurately as possible without getting adversely affected by direct solar

radiation or other heat or refrigeration sources.

The controller can also be used in a portable manner. It features a fold-out stand allow-

ing it to be placed on a horizontal surface such as a bedside table.

Mounting height is about 1.5 m above the floor.

The unit can be fitted to a recessed conduit box.

Key

5/10

Siemens Room temperature controllers CE1N3070en

Building Technologies 20.11.2007

When mounting the controller, fix the baseplate first. The receiver does not require a

baseplate. Make the electrical connections and fit and secure the receiver (also refer to

the separate mounting instructions).

Mount the controller on a flat wall and in compliance with local regulations.

If there are thermostatic radiator valves in the reference room, set them to their fully

open position.

Controller and receiver are maintenance-free.

If battery symbol appears, the batteries are almost exhausted and must be re-

placed.

To reset the controller, press both the Test and Learn buttons on the rear of the unit.

To reset the receiver, press the RESET button on the unit front.

All individual settings are then reset to their default values.

Technical data

Operating voltage DC 3 V (2 x 1.5 V AA alkaline batteries)

Battery life >1 year (AA alkaline batteries)

Internal:

Thermistor 10 kΩ± 1% at 25 °C

Switching differential SD 1 K

Setpoint setting range 5…30 °C

Factory setting comfort setpoint 20 °C

Resolution of settings and displays

Setpoints 0.5 °C

Actual value displays 0.5 °C

Operation IEC 721-3-3

Climatic conditions Class 3K5

Temperature 0…+40 °C

Humidity <90% r.h.

Transport IEC 721-3-2

Climatic conditions Class 2K3

Temperature -25…+60 °C

Humidity <95% r.h.

Mechanical conditions Class 2M2

Storage IEC 721-3-1

Climatic conditions Class 1K3

Temperature -10…+60 °C

Humidity <90% r. h.

Mounting, installation

and commissioning

Maintenance

Change of batteries

Reset

Power supply

Sensor inputs

Operational data

Environmental conditions

Altri manuali per RDH10RF

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Siemens Regolatori di temperatura

Siemens

Siemens RDJ10RF/SET Manuale utente

Siemens

Siemens SITRANS TSinse rt Guida per l'amministratore

Siemens

Siemens Free Energy Band RCU61U Manuale del proprietario

Siemens

Siemens REV24RF Istruzioni per l'installazione

Siemens

Siemens RLA162 Manuale utente

Siemens

Siemens RDU50U Manuale del proprietario

Siemens

Siemens RDJ10RF/SET Manuale utente

Siemens

Siemens QAW910 Manuale utente

Siemens

Siemens REV24RF Manuale utente

Siemens

Siemens RDE10.1DHW Manuale utente

Siemens

Siemens RDE10 Series Manuale utente

Siemens

Siemens AQR2531 Series Manuale utente

Siemens

Siemens RCU50U Manuale del proprietario

Siemens

Siemens REA23.03RF Manuale utente

Siemens

Siemens 2000 Series Manuale utente

Siemens

Siemens REA22 Manuale dell'operatore

Siemens

Siemens Landis & Staefa REV11 Series Manuale utente

Siemens

Siemens RLM162 Manuale utente

Siemens

Siemens 2200 Series Manuale utente

Siemens

Siemens Polygyr-Compact Manuale del proprietario

Siemens

Siemens REV15 series Manuale utente

Siemens

Siemens RDD310 Manuale utente

Siemens

Siemens 24RFDC/SET Manuale utente

Siemens

Siemens RDF110 Manuale utente

Manuali Regolatori di temperatura popolari di altre marche

Swegon

Swegon LUNAd MB Manuale utente

Lucky Reptile

Lucky Reptile Thermo Control II Manuale utente

SENSORMETRIX

SENSORMETRIX Argon 100 Manuale utente

Fuji Electric

Fuji Electric PXE4 Manuale utente

Yuyao gongyi

Yuyao gongyi XMT-808 series Manuale utente

Selec

Selec TC544C Manuale utente

P.W. KEY

P.W. KEY rt-208gt Manuale utente

Future Design

Future Design FDC-9200 Manuale utente

BH Thermal

BH Thermal BriskONE Manuale utente

Omron

Omron E5EX-H Manuale utente

West Control Solutions

West Control Solutions KS 45 Guida rapida

MCS

MCS RITC-15B Manuale utente

SMC Networks

SMC Networks Thermo-con INR-244-639 Manuale utente

eltherm

eltherm Ex-TC It Series Manuale utente

Omron

Omron C200H-TV Series Manuale utente

industrie technik

industrie technik CA1 Manuale utente

KRAL

KRAL EET 32 Manuale utente

dixell

dixell XR420C Schema elettrico