Siemens RDH10RF/SET Manuale utente
CE1B3070en / 01.03.2010 Subject to alteration Siemens Building Technologies / HVAC Products
Operating instructions RDH10RF/SET
RDH10RF/SET consists of a RDH10RF wireless temperature controller and a RCR10/433 receiver. The RDH10RF
allows you to set the desired room temperature (setpoint) at the time you want. The unit features an ergonomic
setting knob for ease of temperature control.
Display
Actual room temperature in ºC
The unit is controlling to the selected
comfort temperature
Indicates when there is demand for
heat
Replace batteries
RF
TEST
Appears on the screen when the
transmitter is being tested.
Setting knob
Warmer/colder knob for
selecting the temperature
setpoint
Battery compartment
Two alkaline batteries type AA, 1.5 V
Commissioning before start-up
Commissioning
•Remove the black transit tabs from the alkaline batteries.
•Check to see if the battery holder is in the correct position.
•If no batteries are inserted, fit 2 alkaline batteries type AA in the battery compartment.
Initial power-up
Once batteries are fitted, all symbols will appear on
the display as shown for about two seconds.
Selecting the required temperature
•Turn the setting knob counter clockwise to
decrease the setpoint, or clockwise to increase the
setpoint in increments of 0.5 °C
•The required temperature is displayed next to
the comfort temperature symbol
Changing the batteries
1. Get two new batteries of type AA alkaline, 1.5 volts.
2. Remove the battery holder, then the batteries, insert new batteries and
replace the battery holder.
The old, set values must be checked!
3. Make certain the old batteries are disposed of properly, in
compliance with environmental requirements.
Energy saving tips without sacrificing comfort
●Never allow room temperatures to exceed 21˚C.
●Air out rooms: Air out rooms for short periods with open windows and
doors.
CE1B3070en / 01.03.2010 Subject to alteration Siemens Building Technologies / HVAC Products
NOTE:
You can press the OVERRIDE button on the receiver to manually switch ON/OFF for a faulty
room unit or transmission protocol.
NOTE:
You must re-execute the workflow for commissioning the set to reestablish a connection between
the room controller and receiver .
Front View Receiver
LED Signal Indicator LED Relay Indicator
Orange LED indicates relay is on.
The signal is good when the
LED flashes green.
A flashing red LED indicates
that there is no signal. OVERRIDE Button
Press this button to overwrite transmitter
values.
RESET: Press the LEARN & OVERRIDE
button for 4 seconds to delete all transmitter
addresses.
LEARN Button
Rear View Room Unit
(Transmitter)
Press the button to learn a transmitter
address.
Learn Button TEST Button
Release learn telegram Used for testing transmission.
Front View Receiver
Configuration instructions for the Siemens RDH10RF/SET
The Transmitter RDH10RF and the receiver RCR10/433 are set to communicate (bonded) with each
other at the factory. If they fail it is necessary to re bond the units due to loss of communication please
follow the following instructions.
1. Reset receiver by simultaneously pressing the LEARN & OVERRIDE button for 4 seconds.
2. Press and release the LEARN button. This set the receiver to learn mode.
3. Press and release the LEARN button on the back of the transmitter.
4. A green flashing or solid LED indicates a good signal, a red flashing or solid LED indicates no
signal.
5. To test transmission, press the TEST button on the transmitter, switches the relay on in
the receiver regardless of temperature. The RF TEST symbol appears on the thermostat display.
6. An orange LED indicates that the relay is on.
Altri manuali per RDH10RF/SET
1
Altri manuali Siemens Regolatori di temperatura
Siemens
Siemens REA23.03RF Manuale utente
Siemens
Siemens RCC10U Manuale del proprietario
Siemens
Siemens REV23RF16A Manuale utente
Siemens
Siemens RDD10.1DHW Manuale utente
Siemens
Siemens UP 237K Manuale utente
Siemens
Siemens RDU50U Manuale del proprietario
Siemens
Siemens QAX910 Manuale utente
Siemens
Siemens POS8.4420/109 Manuale utente
Siemens
Siemens DT-11 Istruzioni per l'installazione e il funzionamento
Siemens
Siemens RDE10.1DHW Manuale utente
Siemens
Siemens RDD310 Manuale utente
Siemens
Siemens RLA162 Manuale utente
Siemens
Siemens REV23.03RF Manuale utente
Siemens
Siemens RDF110 Manuale utente
Siemens
Siemens RCC30 Manuale utente
Siemens
Siemens RLE132 Manuale utente
Siemens
Siemens RDJ10RF/SET Manuale utente
Siemens
Siemens 24RFDC/SET Manuale utente
Siemens
Siemens SITRANS TSinse rt Guida per l'amministratore
Siemens
Siemens KIT911 Manuale di istruzioni
