SIIG CE-H21F11-S1 Manuale utente
1
4x4HDMI1.3CAT5eMatrix
Quick Installation Guide
04-0554A
Introducing the 4x4 HDMI 1.3 CAT5e Matrix
The4x4 HDMI 1.3 CAT5e Matrix providesthemostflexible
and cost effective solution in the market to route high
definition video sources plus multi-channel (up to 7.1-
channel) digital audio from any of the four HDMI sources
to the remote displays.
FeaturesandBenefits
• HDMI 1.3c and HDCP compliant
• Chipset: Silicon Image
• Video bandwidth: 10.2 Gbps (single-link 340MHz)
• Input TMDS signal: 1.2V (peak-to-peak)
• Input DDC signal: 5V (peak-to-peak)
• Resolution: 480i / 480p / 720p / 1080i / 1080p
(60Hz)
• Transmission:
-720p/1080i (HD): 165ft (CAT5e) & 180ft (CAT6)
-1080p (full HD): 115ft (CAT5e) & 130ft (CAT6)
• Power supply: 5V DC, 6A
• Power consumption: 20 Watts (max)
• Housing: metal (for better RF shielding)
2
PackageContents
• 1x Matrix Transmitter
• 4x Matrix Receiver
• Power Adapter
• IR emitting extension cable
• 4x IR receiving extension cable
• IR Remote Controller
• Installation CD
• Quick Installation Guide
Layout
Figure 1: Transmitter Front Layout
12345
6
1. Power: Power indicator LED
2. IR: IR receiver LED
3Input: Input source indicator LED (1-4)
4. HP 1–HP 4: Connection status indicator LED
5Port 1–Port 4: Input source channels mapping LED
for each output channel
6Port 1 –Port 4 Selector: Push button to select input
channel
3
Figure 2: Transmitter Back Layout
7. ON–OFF: Power ON/OFF
8. RS-232: RS-232 control port
9. +5V DC: 5V DC power jack
10. SW Main: DIP switches (see DIP Switch below in
the next page)
11. SW 1–SW 4: DIP switch (see DIP Switch in the next
page)
12. IN 1–IN 4: HDMI inputs
13. IR 1–IR 4: IR extender jacks for individual HDMI
source
14. OUT 1–OUT 4: RJ-45 TMDS/DDC outputs for each
output channel
15. IR Main: IR extender jack for all HDMI sources
(default socket for IR emitter)
78910 11 12 13 14 15
4
DIP Switch Position
Pin #1 Pin #2 Video Audio Description
Stereo1Default Mode2 : 1080 & Stereo
1080p
ON
Safe Mode3: Enforce the system
output at 720p/1080i video and
stereo audio for basic compatibility
EDID Learning Mode5: For learning
EDID from the display while playing
any received HDMI audio format
EDID Learning & Stereo Mode5:
For learning EDID from the display
while enforcing stereo output if any
HDTV cannot play surround sound
ON
720p Stereo
Bypass4Bypass4
Stereo Stereo
SW 1-SW 4 for EDID/Audio
ON
ON
OFF
OFF
OFF
OFF
Note:
1. If the HDTV shows video without audio, try setting
audio mode to stereo.
2. Default Mode -Factory default of SW1-SW4: Pin#1-
OFF & Pin#2- OFF for 1080p with stereo.
3. If you encounter an audio/video output problem
during system installation, set the appropriate SW
switch to Safe Mode to check your system setup.
4. In Bypass Mode the Matrix will play the audio/
video signals in original format. In this mode you
mayencounter compatibility issuesamongdifferent
HDMI sources and displays. If you cannot get the
audio and/or video to display, change the DIP
switch setting to Default Mode or Safe Mode to
verify functionality of the device.
5
5. EDID Learning: Set Pin#1- ON first then connect the
HDMI Input to the HDTV through an HDMI cable.
Wait for 20 seconds. The EDID of the display will be
saved. If you want to learn the EDID from another
HDTV, you must set Pin#1 at OFF first and repeat
this process.
Figure 3: Receiver Front Layout
•IN: Push button to switch input source channels in
sequential order
•EQ: 8-level equalization control for HDMI signals.
0-7 = strongest–weakest. It is recommended to
switch from 0 to 7 to find the optimal visual
experience
•Source LED: Indicates input source
•HDMI Out: Connect to HDTV via HDMI cable
•IR: Plugs in IR receiver cable
EQ
IN
IR
HDMI Out
Source LED
6
Figure 4: Receiver Back Layout
+5V DC TMDS DDC
•+5V DC: 5V power jack (optional)
Note: The 4x4 HDMI 1.3 CAT5e Matrix has been
tested extensively and found that it doesn’t require
an external power supply. However, if you find it
not working please connect a 5V power supply
similar to the power supply that powers the
Transmitter.
•TMDS: Connects to TMDS Out of the Transmitter
via RJ45 cable
• DDC: Connects to DDC Out of the Transmitter via
RJ45 cable
IR Sockets
IR Emitter Cable (for Matrix Transmitter)
•IR Main: The default location for IR emitter
extension cable. Transmits IR command signals
received from any of the four remote receivers to all
of the HDMI sources
•IR1: IR emitting cable connected here. Transmits IR
command signals from the remote receivers that are
connected to input channel 1 (IN 1)
7
•IR2: IR emitting cable connected here. Transmits IR
command signals from the remote receivers that are
connected to input channel 2 (IN 2)
•IR3: IR emitting cable connected here. Transmits IR
command signals from the remote receivers that are
connected to input channel 3 (IN 3)
•IR4: IR emitting cable connected here. Transmits IR
command signals from the remote receivers that are
connected to input channel 4 (IN 4)
IRReceiver Cable(for MatrixReceiver)
•IR: IR receiving cable connected here. Receives IR
command signals from the IR remote control of the
transmitter and all other HDMI source devices.
Hardware Installation
The4x4HDMI1.3CAT5eMatrixas master
1. Connect your HDMI sources to the HDMI inputs
(IN 1 - IN 4) on the Matrix Transmitter.
2. Connect each DDC output on the transmitter to
respective DDC input on the Matrix Receiver.
3. Connect each TMDS output on the Matrix
Transmitter torespective TMDS inputon theMatrix
Receiver.
4. Connect IR emitter cable to the Matrix Transmitter
and direct the IR emitter to the built-in IR receiver of
the HDMI source devices.
5. Connect the +5V DC power supply to the Matrix
Transmitter.
6. Power on all HDMI source devices.
7. Power on the Matrix Transmitter.
8
The4x4HDMI1.3CAT5eMatrixasreceiver
1. Connect each HDMI output to HDMI displays.
2. Connect the TMDS input on the Matrix Receiver to
the TMDS output on the Matrix Transmitter.
3. Connect the DDC input on the Matrix Receiver to
the DDC output on the Matrix Transmitter.
4. Connect IR receiver cable and place the IR receiver
at the appropriate position to be able to receive the
IR signals sent from the users.
5. Use the EQ dial to adjust the equalization until the
picture and sound are clear.
Operation and IR Control
SourceSide
Method A: Push Button
Push the Port Select button on the front panel, the source
will change in sequential order.
Method B: IR Remote Control
1. Please press to enter IR control mode.
Note: If Matrix Transmitter receives the IR
commands, the LED will flash. If not, try again.
2. Decide which output port to be controlled by
pressing F1 to F4, and wait a few seconds for audio/
video of next channel to appear.
Note: If the setting is correct, the corresponding
LED will flash. If not, press output port select
button or repeat step (1) and (2).
9
Figure 5: Remote Control
3. Use the left or right keys to select input source
device and wait a few seconds for the audio/video
of the next channel to appear.
Note: If the setting is correct, the corresponding
LED will flash. If there is no response, please wait
until the LED stops flashing, and try again. Left
button to switch channels in ascending order (1, 2, 3,
4,1, ...)Right buttonto switchchannelsindescending
order (1, 4, 3, 2, 1, …)
DisplaySide
Method A: Push button
Push the switch buttons of respective output channels
and the output channel will switch from HDMI source 1
to source 4 in sequential order, wait a few seconds for
audio/video of next channel to appear.
Method B1: IR remote control
1. Press Power on button to enable IR control function.
Note: If Matrix Receiver receives the IR command,
the LED will flash. If not, try again.
F1
F2
F3
F4
HMDI output #1
HMDI output #2
HMDI output #3
HMDI output #4
Power On
10
2. Press hot key, F1-F4, for input source. Please refer
Figure 5 in page 9.
MethodB2:IRremotecontrolforcontrollingtheHDMI
sources
Users can use the corresponding IR remote to control
respective DVD player or any HDMI compliant devices
including Matrix Receiver itself with IR control at any
display site.
RS-232 Serial Port Control
MethodC:SoftwareControlthroughRS-232
Figure 6: RS-232
Scan
Open
Close Qick Setup Buttons
Output Channel Setup
Input Channel Setup
Indice
Altri manuali SIIG Commutatore a matrice
SIIG
SIIG AV-GM07X3-S1 Manuale utente
SIIG
SIIG AV-GM07U3-S1-V2 Manuale utente
SIIG
SIIG CE-H27Q11-S1 Manuale utente
SIIG
SIIG AV-GM08G3-S1 Manuale utente
SIIG
SIIG AV-GM07A3-S1 Manuale utente
SIIG
SIIG AV-GM0783-S1 Manuale utente
SIIG
SIIG AV-GM07J3-S1 Manuale utente
SIIG
SIIG CE-H23H11-S1 Manuale utente
SIIG
SIIG AV-GM0743-S1 Manuale utente
SIIG
SIIG AV-GM0733-S1 Manuale utente
SIIG
SIIG AV-GM07G3-S1 Manuale utente
SIIG
SIIG AV-GM0803-S1 Manuale utente
SIIG
SIIG AV-GM06Y3-S1 Manuale utente
SIIG
SIIG 4x2 HDMI Manuale utente
SIIG
SIIG AV-GM07N3-S1 Manuale utente
SIIG
SIIG AV-GM07P3-S1 Manuale utente
SIIG
SIIG AV-GM06X3-S1 Manuale utente
SIIG
SIIG AV-GM07M3-S1 Manuale utente
SIIG
SIIG AV-GM07U3-S1 Manuale utente
SIIG
SIIG AV-GM0823-S1 Manuale utente
