Silicon Graphics 1600SW Manuale utente

Silicon Graphics 1600SW™

Flat Panel Monitor

Owner’s Guide

Document Number 007-3869-002

CONTRIBUTORS

Written by Judy Muchowski and Kameran Kashani

Illustrated by Kwong Liew and Kameran Kashani

Engineering contributions by Dan Evanicky, Lisa Feldman, Lori Gager, David

Hanttula, Ken Klingman, Oscar Medina, Jonathan Mendelson, Alice Meng,

Steve Profﬁtt, Larry Roberts, I-Ching Wang, Michael Wright.

The contents of this document may not be copied or duplicated in any form,

in whole or in part, without the prior written permission of Silicon Graphics,

Inc.

RESTRICTED RIGHTS LEGEND

Use, duplication, or disclosure of the technical data contained in this

document by the Government is subject to restrictions as set forth in

subdivision (c) (1) (ii) of the Rights in Technical Data and Computer Software

clause at DFARS 52.227-7013 and/or in similar or successor clauses in the

FAR, or in the DOD or NASA FAR Supplement. Unpublished rights reserved

under the Copyright Laws of the United States. Contractor/manufacturer is

Silicon Graphics, Inc., 2011 N. Shoreline Blvd., Mountain View, CA

94043-1389.

Silicon Graphics is a registered trademark and 1600SW is a trademark of

Silicon Graphics Inc. Post-it is a registered trademark of 3M.

iii

About This Guide

This guide is translated into several languages. The guide (except for

compliance information) is duplicated in each language in separate

sections. The section for each language begins with a table of contents,

and the page numbers for each section have two-character preﬁxes

denoting the speciﬁc language:

Within each language section are the necessary instructions and

information for setting up the hardware, using the basic hardware

features, basic troubleshooting, and product warranty and support.

At the end of this guide is Appendix A, “Statements of Compliance,”

which provides local compliance and regulatory information.

Language Section: Table of Contents Starts on Page:

English EN-v

French/Français FR-iii

German/Deutsch DE-iii

Italian/Italiano IT-iii

Spanish/Español ES-iii

Japanese/ JA-iii

Korean/ KO-iii

EN-v

Contents

About This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EN-vii

1. Setting Up and Using the Flat Panel Monitor . . . . . . . . . . . . . . EN-1

Using the Flat Panel Monitor With a Standard CRT . . . . . . . EN-1

Unpacking the Flat Panel Monitor . . . . . . . . . . . . . . . . . . . . . . EN-2

About the Flat Panel Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . EN-3

Connecting the Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EN-4

Turning On the Flat Panel Monitor. . . . . . . . . . . . . . . . . . . . . . EN-5

Adjusting the Viewing Position . . . . . . . . . . . . . . . . . . . . . . . . EN-5

Turning Off the Flat Panel Monitor . . . . . . . . . . . . . . . . . . . . . EN-7

Removing the Flat Panel Monitor From Its Base and

Replacing It. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EN-7

Replacing the Flat Panel Monitor On Its Base . . . . . . . . . EN-9

Using a Screen Saver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EN-9

Adjusting the Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EN-10

Adjusting the White Balance (White Point). . . . . . . . . . . . . . EN-10

About the Sensor Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EN-10

Recommended Use and Viewing Angles . . . . . . . . . . . . . . . EN-11

EN-vi

2. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EN-13

LED States. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EN-13

Troubleshooting Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EN-14

No Image on the Flat Panel Monitor . . . . . . . . . . . . . . . . EN-15

Image Appears Too Light or Too Dark. . . . . . . . . . . . . . EN-16

Image Is Dim When Monitor Is First Turned On . . . . . EN-16

Bright Dots on the Monitor. . . . . . . . . . . . . . . . . . . . . . . . EN-16

Diagnostic Tests for the Flat Panel Monitor. . . . . . . . . . EN-17

Warranty Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EN-17

Returning the Flat Panel Monitor . . . . . . . . . . . . . . . . . . . . . . EN-17

3. Maintenance, Technical Specifications and Regulatory

Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EN-19

Cleaning and General Care of the Flat Panel Monitor. . . . . EN-19

Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EN-20

Manufacturer’s Regulatory Declarations. . . . . . . . . . . . . . . . EN-23

Shielded Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EN-23

Electrostatic Discharge. . . . . . . . . . . . . . . . . . . . . . . . . . . . EN-24

A. Statements of Compliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-1

FCC Class B Conformance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-1

Electromagnetic Emissions . . . . . . . . . . . . . . . . . . . . . . . . . . .A-2

ENERGY STAR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-3

TCO ‘95 Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-3

Industry Canada Notice (Canada Only) . . . . . . . . . . . . . . . . . . .A-3

CE Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-3

VCCI Notice (Japan Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-4

Korean Regulatory Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-4

NOM 024 Information (Mexico Only) . . . . . . . . . . . . . . . . . . . . .A-5

EN 55022 Compliance (Czech Republic Only) . . . . . . . . . . . . . .A-5

Polish Notice (Poland Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-6

EN-vii

Introduction

Congratulations and welcome to the world of precise color. You have

purchased a professional-quality, digitally driven, ﬂat panel monitor.

This ﬂat panel monitor supports true color (24-bit) with a screen

resolution of 1600 x 1024 pixels.

Because of its high resolution, this monitor must be connected to a

graphicsadapter cardor systemthat supportstheOpenLDI digitalﬂat

panel interface. You cannot plug this monitor into a typical analog

VGA connector.

This guide contains instructions that are speciﬁc to the ﬂat panel

monitor. It assumes that the adapter board that drives the monitor has

been installed in your computer. Information related to your

computer, adapter board, and other peripherals is located in the

documents that ship with them.

• Chapter 1, “Setting Up and Using the Flat Panel Monitor,”

explains how to unpack, set up, and adjust the ﬂat panel monitor.

• Chapter 2, “Troubleshooting,” contains troubleshooting and

product support information.

• Chapter 3, “Maintenance, Technical Speciﬁcations and

Regulatory Information,” tells you how to take care of the ﬂat

panel monitor. It also contains technical speciﬁcations and

regulatory information.

Setting Up and Using the Flat Panel Monitor EN-1

Chapter 1

1. Setting Up and Using the Flat Panel Monitor

This chapter explains how to unpack the ﬂat panel monitor and set it

up with your computer.

The ﬂat panel monitor is driven by an adapter board that is installed

in your computer. In some cases, the adapter board and software are

installed at the factory before shipment; in other cases, you need to

install them yourself.

• If the ﬂat panel adapter board and software have already been

installed, continue with these instructions.

• If you are installing the adapter board and software, install them

now, using the instructions and CD that come with the adapter

board. Be sure to read any documentation or release notes on the

CD for instructions speciﬁc to your computer. Then return to this

manual.

In addition, see your computer’s documentation (in most cases, an

owner’s guide) for any information speciﬁc to your computer.

Using the Flat Panel Monitor With a Standard CRT

If you plan to use the ﬂat panel monitor along with a standard

cathode-ray tube (CRT) monitor, be aware of the following:

• The ﬂat panel monitor was not designed to be used

simultaneously with a conventional cathode-ray tube (CRT)

monitor when both monitors are attached to the same graphics

adapter board. If you are operating your ﬂat panel monitor from

EN-2 Chapter 1

a PCI or AGP board and have a CRT monitor connected to your

system, you may need to use your system’s setup utility to select

a primary (default) monitor.

• If your system can use separate, dual PCI or AGP cards, then you

may be able to use the ﬂat panel monitor and a CRT monitor at

the same time. See your system’s owner’s guide and any

documentation provided with the adapter board for more

information.

Unpacking the Flat Panel Monitor

To unpack and set up the ﬂat panel monitor, follow these steps.

(Unpacking instructions are also printed on the shipping box.) Save

the original shipping materials in case you need to return the monitor

for service.

1. Open the box, remove the top carton and AC power card, and set

both aside.

2. Using the lifting strap that is packed around the monitor,

carefully lift the monitor, its base, and some protective foam

pieces from the box. Place this assembly on a ﬂat surface.

3. Remove the top foam support, then lift the monitor from the

bottom foam piece and remove the plastic bag.

4. Remove the protective ﬁlm from the screen by peeling it away

slowly from one corner, keeping the peeled off portion as close to

the monitor’s surface as possible. Be careful not to get

ﬁngerprints on the exposed coated glass surface. Keep this

protective ﬁlm in case you need to return the monitor for service.

Caution: The screen is made of glass coated with optical

ﬁlms and is the most expensive component in the

monitor. A blow from a sharp instrument such as

a pen can scratch the surface or break the glass.

Altri manuali per 1600SW

Indice

Altri manuali Silicon Graphics Monitor

Silicon Graphics

Silicon Graphics Presenter Manuale utente

Silicon Graphics

Silicon Graphics Reality Center Manuale utente

Silicon Graphics

Silicon Graphics F180 Manuale utente

Silicon Graphics

Silicon Graphics GDM-4011P Manuale utente

Silicon Graphics

Silicon Graphics C220 Manuale utente

Silicon Graphics

Silicon Graphics GDM-FW9011 Manuale utente

Silicon Graphics

Silicon Graphics GDM-5011P Manuale utente

Silicon Graphics

Silicon Graphics F181 Manuale utente

Silicon Graphics

Silicon Graphics Presenter 1280 Manuale utente

Silicon Graphics

Silicon Graphics GDM-5411 Manuale utente

Silicon Graphics

Silicon Graphics GDM-5411 Manuale utente

Silicon Graphics

Silicon Graphics Silicon Graphics F190 Manuale utente

Silicon Graphics

Silicon Graphics 1600SW Manuale utente

Manuali Monitor popolari di altre marche

Linear Acoustic

Linear Acoustic LQ-1000 Manuale utente

AOC

AOC I2579V Manuale utente

Gateway

Gateway FPD1520 Manuale utente

Furuno

Furuno Mu 120c Manuale utente

Asus

Asus VB171D - 17" LCD Monitor Manuale utente

Dell

Dell S2230MX Istruzioni utente

Philips

Philips 107C64 Manuale utente

Dell

Dell S2409WFP Manuale utente

EverFocus

EverFocus EN-7517E Manuale utente

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuale utente

Dell

Dell Precision 7680 Manuale di istruzioni

LG 50PM1M - - 50" Plasma Panel Manuale utente

Bosch

Bosch DDU 9 Manuale utente

Acer

Acer A231HL Manuale utente

Philips

Philips 86BDL4152T Manuale utente

NEC

NEC AccuSync LCD5V Manuale utente

Emay

Emay SleepO2 Manuale utente

IBM

IBM 6360 Istruzioni per l'installazione