Silver Wings CR.42 Manuale utente
1:32 FIAT CR.42
BUILD GUIDE
General
This kit gives the builder the option to do either an Italian, German or Swedish version. Be sure to review the
instructions and highlight which parts you will need for the version you are building. Also note that I used standard
superglue for all assembling, with the exception of the struts, where I used slower setting superglue gel to give me
more time for adjustments.
Parts Cleanup
As with other Silver Wings kits, parts cleanup is fairly simple, and due to the soft resin they use for their kit, a sprue
cutter can even be used to snip most parts from their pour stubs. After that, a few scrapes with the Xacto knife and/or
sanding stick and the part is ready for use.
With these kits, since there are no part numbers to worry about, I like to clean up all the parts and then begin the
build. The only exception to this is the struts. Any parts can be painted as appropriate after cleanup and before
assembly as well. A few things to note when preparing your kit parts for use:
Do not remove the number "tabs" from the struts (unless you mark them in some other way, such as a tape
tag) as the numbers are crucial in aiding proper strut placement. (Photo 1)
The wings have excess resin “rods” on the upper tips (see Photo 2), these must be removed as the outer wing
should be smooth.
Check your fuselage framing for any breaks before you remove the pour blocks. You should repair any breaks
with superglue before removing the pour blocks.
If you intend to use the kit provided cockpit frame cross brace tubes, be sure to measure them before you
remove them from the pour stubs as I found I had to trim carefully in order to not end up with tubes that were
too short.
Take care in removing the pour block from the seat back, as there should be a lip at the top.
There are two different types of engine cylinders. Be sure to keep them organized as one set goes on the front
of the engine, the other on the rear (front on the left, rear on the right in Photo 3). Some of the engine
cylinders may have some slight seams on the sides that require cleanup, however any that you "miss" during
cleanup will likely not be visible on the finished model without searching really hard for them.
Test fit your propeller to the engine block and enlarge the hole as necessary to achieve a good fit.
The cockpit sides have 3 frames that must be attached, and are placed in bags labeled "A"; "B" and "C" (Photo
4). As they look similar, I recommend you clean up each set, and then place them back in the bags until you
are ready to attach them.
The engine cowl has some pour channel remains on the inside of the cowl flaps (Photo 5). While a portion of
these look like they may be actuating rods of some kind, they should be removed and the cowl flap area should
be smooth on the inside.
Interior Subassemblies
There are a few items that can be assembled before installation in the cockpit, as indicated on page 3/4 of the
instructions. I'll review them here:
Instrument Panel: Note that part PE-2 is for the German/Swedish versions, while part PE-2a is for the Italian
version. Cut out the instrument backing from the clear film and paint the back white, and install in in position
on the PE instrument panel. Prior to attaching the PE panels to the resin instrument panels, you should test fit
the resin panels to the PE gun sight "box" as some trimming of the rear of the resin panels may be necessary to
get a good fit (don't worry about destroying any detail, the back in not visible on the finished model). If
possible, I recommend attaching the PE panels to the resin panels after the resin panels have been attached to
the cockpit framing and test fit to the fuselage.
I left parts PE-4 off of my build as they are not really visible on the finished model.
Use the end of your paintbrush to bend the PE rudder straps into shape and attach them to the rudder bar.
The provided PE shoulder belts and pad are "interesting" to assemble, but you can leave them off until the
fuselage is completed if you prefer.
While the PE control levers fit into the slots in the side control panel, you may want to drill small holes to give
them a stronger attachment point.
Cockpit Assembly
Cockpit assembly is shown on pages 2 and 5 of the instructions. If you've built any other Silver Wings kits, assembly
should be familiar to you.
I started my assembly by cutting the provided resin cross-braces to the appropriate lengths as indicated (you
may find it easier to use plastic or metal rod) on page 2. I then attached the rods and lower support frames to
one side of the framing (see Photo 6).
I then attached the opposite side framing piece, starting at one end and moving towards the other to ensure
the best alignment (see Photo 7).
I then added the upper rear framing (Photo 8) and finaly the upper front framing (Photo 9). Once complete,
test fit the frame into the fuselage to be sure everything is lined up properly.
Next, I attached the PE framing to the floor. I attached PE20 and PE21 and let dry (Photo 10). It would appear
that PE22 is meant to be folded in half and then attached, but it was rather thick when I tried that, so I ended
up cutting it in half and attaching it to the cockpit floor (Photo 11).
Attach the seat subassembly in position, and then add the rudder bar, control column, and side control panel
subassemblies as well as the two tanks (Photos 12/13)
Slide the floor into place, and then attach the PE side consoles as appropriate (see page 2 of the instructions)
see Photos 14-17.
I then attached the firewall subassembly to the front of the cockpit floor (Photos 18/19) rather than to the
fuselage sidewall as shown on page 7 of the instructions. Fit was so good on mine I did not need to glue it,
which gives the option to wiggle it should you need to for final positioning in the fuselage.
Attach the seatback to the upper cockpit frame using the flange on the seat. You should be able to move the
bottom slightly to get it into position. Attach the rear cockpit bulkhead in position on top of the seat flange
(Photo 20). You can attach the shoulder belts at this time, or later in the build.
Although not shown in the instructions, attach the instrument panel(s) 11mm back from the cockpit frame
front. Test fit your completed cockpit in the fuselage.
Fuselage Assembly
Fuselage assembly is covered on page 7/8 of the instructions.
Prior to assembling the fuselage, I drilled out an additional hole on each side of the wing root to allow the
metal rod on the lower wing to fit into the fuselage (Photo 21)
Test fit the windscreen to the fuselage, and trim the fuselage attachment area as needed to ensure optimal fit
(namely the pointed area where the rear of the windscreen fits)
If needed, cut and remove the section of the tail wheel fairing as indicated for the Swedish version.
Attach the fuselage frames (labeled "A", "B" and "C") into position as indicated (Photo 22)
As mentioned previously, I prefer to install the forward bulkhead to the cockpit floor rather than the fuselage
halve as shown in the instructions
Attach the tail wheel (or trap between the fuselage halves if you want it to move)
Install the completed cockpit frame to one of the fuselage halves. Photos 23 and 24 show everything ready to
be closed up.
Indice
