Video Inspection Camera with Large Screen 4.3"923943
9
silverlinetools.com
General Safety
WARNING: Read all safety warnings and all instructions.Failure to follow the warnings and
instructions may result in electric shock, re and/or serious injury.
WARNING: This power tool is not intended for use by persons (including children) with reduced
physical or mental capabilities, or lack of experience or knowledge unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children must be supervised to ensure that they do not play with the power tool.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-
operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit.Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of
ammable liquids, gases or dust. Power tools create sparks which may ignite the dust
or fumes.
2) Electrical safety
a) Avoid body contact with earthed or grounded surfaces, such as pipes,radiators, ranges
and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
b) Do not expose non-waterproof electrical devices to rain or wet conditions. Do not
submerge non-pressure-rated devices in water. Water entering an electrical device will
increase the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common sense when operating an electrical
device. Do not use potentially dangerous electrical devices while you are tired or under
the inuence of drugs, alcohol or medication. A moment of inattention while operating
potentially dangerous devices may result in serious personal injury.
b) Use personal protective equipment including eye protection where appropriate. Protective
equipment used for appropriate conditions will reduce personal injuries.
c) Do not overreach. Keep proper footing and balance at all times. This enables better control
of the device in unexpected situations.
4) Use and care
a) Do not force the device. Use the correct device for your application.The correct device will do
the job better and safer at the rate for which it was designed.
b) Do not use the electrical device if the switch does not turn it on and off. Any device that
cannot be controlled with the switch is dangerous and must be repaired.
c) Use the device and its accessories in accordance with these instructions, taking into
account the conditions and the task to be performed. Use the device for operations different
from those intended could result in a hazardous situation.
5) Service
a) Have your power tool serviced by a qualied repair person using only identical
replacement parts. This will ensure that the safety of the power tool is maintained.
Additional Safety Notes
• The unit is not shock resistant. Do not drop the unit from height or otherwise subject it to high
impacts
• The camera lens and cable are water resistant when the unit is fully assembled.The main unit
with LCD screen is not water resistant
• Do not allow water or other liquids to enter the unit. Do not use the camera if condensation
forms inside the lens. Allow moisture to evaporate before using
• Turn OFF the system when it is not in use
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses,and can radiate radio frequency energy and,if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However,there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment OFF and ON, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
Consult the dealer or an experienced radio/TV technician for help
Electromagnetic Compatibility (EMC)
The term electromagnetic compatibility is taken to mean the capability of the product to function
smoothly in an environment where electromagnetic radiation and electrostatic discharges are
present and without causing electromagnet interference to other equipment.
Note: The Silverline Video Inspection Camera with Color LCD Monitor conforms to all applicable
EMC standards. However, the possibility of it causing interference in other devices cannot be
precluded.
1Camera Lens Housing
2Camera Cable/Lens Holder
3Flexible Camera Cable
4Power Indicator Light
5LCD Screen
6Power Button
7Camera Lens LED Light Button
8Zoom Button
9Video Out Socket
10 Screen Rotation Button
11 LCD Brightness Button
12 Battery/Cell Insert Tabs
13 Battery/Cell Compartment Cover
14 Camera Cable Housing Release Tabs
15 Video Cable
16 Hook
17 Mirror
18 Magnet
19 Accessory Ring
20 Carry Case
Product Familiarisation
Intended Use
Video inspection camera for inspecting hard-to-reach places in lofts,buildings, or for automotive
work. Flexible waterproof camera cable with included accessories: magnet,mirror,and hook. The
camera features brightness-adjustable LED lights around the lens.The LCD monitor handset is
lightweight and compact with 2x digital zoom, powered by 4 xAA batteries/cells (included).
Unpacking Your Tool
• Carefully unpack and inspect your tool.Familiarise yourself with all its features and functions
• Ensure that all parts of the tool are present and in good condition
• If any parts are missing or damaged, have such parts replaced before attempting to use this tool
Before Use
Battery/cell installation
Note: This tool requires 4 x AAbatteries/cells (included).The battery/cell compartment is on the rear
of the device behind the LCD Screen (5).
1. Remove the Battery/Cell Compartment Cover (13) (Fig.I)
2. Install batteries/cells correctly,ensuring the positive (+) and negative (-) terminals on the
batteries/cells match up with the device terminals (Fig.I)
3. Ret the cover
4. The device is ready to use
Note: In the top corner of the LCD Screen is the icon, which shows the battery charge status.
When the battery becomes empty,it will be time to change the batteries.Replace all of the batteries
at the same time.
923943_Manual.indd 9 18/09/2019 16:19
