Silverpak 17D Manuale utente
17D / 17DE
INTEGRATED STEP MOTOR AND DRIVER
WithEncoderOption
USER MANUAL
Version 1.05
Page 2 Version 1.05
Silverpak 17D 7/22/2010
Thank you for purchasing the Silverpak 17D or 17DE - Integrated Motor and R208 Driver.
This product is warranted to be free of manufacturing defects for one year from the date of
purchase.
Our technical support group is glad to work with you in answering your questions. If you
cannot find the solution to your particular application, or, if for any reason you need
additional technical assistance.
PLEASE READ BEFORE USING
Before you start, ensure that there is a suitable DC power supply. A current limited lab
supply is recommended for first time users to guard against the possibility of miswiring. In
addition, a suitable STEP and DIRECTION pulse source is also required.
DISCLAIMER
The information provided in this document is believed to be reliable. However, no
responsibility is assumed for any possible inaccuracies or omissions. Specifications are
subject to change without notice.
SERVO-DRIVEreserves the right to make changes without further notice to any products
herein to improve reliability, function, or design. SERVO-DRIVE does not assume any
liability arising out of the application or use of any product or circuit described herein;
neither does it convey any license under its patent rights, nor the rights of others.
CHANGES TO THE DRIVER BOARD
The Silverpak 17D/DE is an integrated Step Motor and R208 driver.
Prior to OCTOBER 1, 2005 the R208 driver board used slower opto-couplers, limiting the
step pulse timing. The old driver board also read step pulses on the rising edge. A revision
change was made on October 1, 2005, using more advanced opto-couplers. These new
opto-couplers can read faster data, yet they are also more sensitive to older PLC step
pulses. If your step pulse signal is not clear, the R208 will pick this up and the motor will
rotate “rough” and irratic. The new boards read step pulses on the falling edge. If the
falling edge of your step pulse is not a clear signal, the motor will rotate “rough” and irratic.
So far, only a small handful of customers have been affected by the change. Mostly those
that use PLC’s from the early 90’s and older. Customers can still request the old R208
boards in quantities of 100 per order (blanket releases are OK). The old boards are under
part number: R208-05.
Special Symbols
Indicates a WARNING and that this information could prevent injury,
loss of property, or even death (in extreme cases).
Page 3 Version 1.05
Silverpak 17D 7/22/2010
Silverpak 17D/DE User Manual
Product: Silverpak 17D and Silverpak 17DE
Version: 1.05
Date: 7/22/2010
Version History
Version Date Description of Changes
1.00
1.01 04/10/2006 Edited Encoder information
1.02 02/02/2007 Standardization of user manuals
1.03 6/7/2007 Added min. order qty for R208-05;
updated description of opto supply.
1.04 8/24/2007 Updated internal resistor info and
recommended resistors for opto-
isolated inputs.
1.05 7/22/2010 Updated error in step frequency.
Updated address.
Page 4 Version 1.05
Silverpak 17D 7/22/2010
TABLE OF CONTENTS
1. FEATURES 5
17DE - ENCODER FEATURES 5
DEFAULT SETTINGS 5
2. ELECTRICAL SPECIFICATIONS 6
POWER SUPPLY REQUIREMENTS 6
DRIVER 6
MOTOR SPECIFICATIONS 6
LOGIC INPUT TIMING 7
4. MECHANICAL SPECIFICATIONS 7
DIMENSIONS 8
5. CONNECTORS 9
6. GETTING STARTED 10
ALTERNATIVE STEP RESOLUTION CONNECTION 11
7. CONFIGURING AND CONTROLLING THE 17D 11
SIGNAL CONTROL SPECIFICATIONS 11
INTERNAL SCHEMATIC 12
RESISTOR VALUES FOR THE OPTO SUPPLY 12
8. TROUBLESHOOTING 13
Page 5 Version 1.05
Silverpak 17D 7/22/2010
FEATURES
•NEMA Size 17, 2 Phase, 1.8° Bipolar Step Motor w/ Built-In Microstepping Driver
•Operates from +12 to 24 VDC
•Step Resolution: Full, 1/2, 1/4, 1/8
•Optically Isolated Step, Direction, and Disable/Enable Inputs
•Automatic Current Reduction with Disable Switch
•Low Power Dissipation
•Efficient Current Control
•Quiet Operation
•Thermal Shutdown, Under-Voltage Protection
•Power-On Indicator
•Power Disable/Enable Control
•Sinusoidal current waveform
•Phase Current Range from 0.35 to 2.0 Amp
•Default Setting is 1.0 Amp RMS or, 1.4 Amp Peak
17DE - Encoder Features
•32 to 1250 cycles per revolution (CPR) chosen by customer
•2 Channel Quadrature
•TTL Squarewave Outputs and optional index (3rd Channel)
•E2 US Digital Encoder
Pin Number Function
1 Ground
2 Index*
3 Channel A
4 + 5 VDC
5 Channel B
Table 1: Encoder Pinouts
*Optional Index Channel
Default Settings
Default Settings
Step Resolution 8x Microstep
Direction of rotation Counterclockwise
Holding Current 23% of motor’s
rated Current
Table 2
The 17D is set to these default settings
when Pins 2, 3, 4, and 5 are left open.
Page 6 Version 1.05
Silverpak 17D 7/22/2010
2. ELECTRICAL SPECIFICATIONS
Power Supply Requirements
Voltage +12 VDC to +24 VDC
Driver
Peak Current: 0.35 to 2.0 Amps OR 0.25 to 1.4 Amps
Motor Specifications
NEMA Size 17
Holding Torque (default – 23% holding current):
DO-4118S 34.5 oz-in
DO-4118M 48.5 oz-in
DO-4118L 63.9 oz-in
Holding Torque (special* – 100% holding current):
DO-4118S 45 oz-in
DO-4118M 63 oz-in
DO-4118L 83 oz-in
Steps per Revolution (1.8° Motor)
200, 400, 800, 1600
*NOTE: The Silverpak 17D/DE by default use 23% of the run current as it’s hold current. If
you require more holding torque, the other option is to use 100% of the run current as your
holding current, which must be special ordered.
Page 7 Version 1.05
Silverpak 17D 7/22/2010
3. OPERATING SPECIFICATIONS
Operating Temperature: -20° to 50° Celsius
Humidity Range: 0 to 95% (non-condensing)
100% duty cycle is OK as long as bottom of unit is 50°C or less (bottom of unit is
where the black heat sink fins are located)
Logic Input Timing
(A) Minimum Command Active Time
Before Step Pulse (Data Set-up Time) 200 nanoseconds
(B) Minimum Command Active Time
After Step Pulse (Data Hold Time) 200 nanoseconds
(C) Minimum Step Pulse Width 1.0 microseconds
(D)Minimum Step Low Time 1.0 microseconds
(E) Maximum Power-Down Recovery Time 1.0 milliseconds
Maximum Step Frequency 500 kHz
Figure 1: Timing Diagram
4. MECHANICAL SPECIFICATIONS
A. Motor Front Shaft Extension Length
Standard length is 0.94”. Customized length is available.
B. Motor Shaft Diameter
Standard shaft diameter is 0.1968”. Customized diameter length is also
available.
C. Overall Body Length
Motor body length is available in various lengths
DO-4118S (2.69”)
DO-4118M (2.92”)
DO-4118L (3.24”)
Page 8 Version 1.05
Silverpak 17D 7/22/2010
Dimensions
Figure 2: Dimensions Diagram
Page 9 Version 1.05
Silverpak 17D 7/22/2010
5. CONNECTORS
A DB-9 female connector cable receives power and provides the control connections for the 17D
Unit. Active signals are optically isolated. An open-collector drive is required to provide pulses
for Step, levels for Direction and Disable/Enable.
PIN # COLOR
(#26 AWG Lead)
FUNCTION DESCRIPTION
1Red +V Motor Supply Voltage. +12 to +24 VDC
2Black SR1 Input Step Resolution 1. Pins 2 & 3 are used to
preset the step resolution by selective
contact to ground (Pin 7)
3Brown SR2 Input Step Resolution 2. Pins 2 & 3 are used to
preset the step resolution by selective
contact to ground (Pin 7)
4Black/White Enable/Disable
Input
This input is used to enable/disable the
output of the driver
5Orange Direction Input This input is used to change the rotation
direction of the motor
6Green Power Ground The ground or return of power supply
connects here.
7White Logic Ground Used to ground to the logic functions (i.e.
step resolution)
8Blue Opto Supply +5 VDC input used to supply power to the
isolated logic inputs**
9Yellow Step Clock Connects to the open-collector drive.
Table 3: Pin Assignments
WARNING! - Do no t apply differential vol tage o n S R1 and S R2, this will dam age
the driver.
** The Resistors shall be connected in series with each Input: Pin 4 (Disable), Pin 5 (Direction), and
Pin 9 (Step) if you are to use an opto supply of more than +5VDC. See Section 7.
Figure 3: DB-9 Female Cable Connector (Rear View)
Page 10 Version 1.05
Silverpak 17D 7/22/2010
6. GETTING STARTED
In order to properly connect your new 17D Unit, first take a look at Figure 4, below.
Here’s a list of the parts needed to make the motor run:
•+12 to 24 Volt Power Supply
•Additional +5 Volt Power Supply
•Function Generator
1. Ensure that the 17D is not connected to the Main Power Supply until the
following procedures have been properly carried out.
2. Connect Pin 8 to the Positive Terminal of the +5 VDC Power Supply.
3. Connect the Negative Terminal of the +5 VDC Power Supply to the Negative
Terminal of the Signal Generator. This will be referred to as the Signal
Ground.
4. Connect Pin 1 and Pin 6 to the Positive and Negative Terminals of the Main
Power Supply, respectively.
5. Adjust the Frequency of the Signal Generator to achieve the desired
operating speed.
Figure 4: Connections Diagram
WARNING! DO NOT DISCONNECT THE DB-9 CABLE FROM THE 17D UNIT WHILE
POWER IS STILL BEING SUPPLIED. THIS MAY CAUSE DAMAGE TO THE INTERNAL
DRIVER BOARD.
WARNING! If you do not have a +5 VDC Power Source, use a Resistor in series to
limit the current of the opto isolators. See following page for Resistor values. If
the current exceeds 10 mA, the opto couplers cease to function.
Questo manuale è adatto per i seguenti modelli
1
Indice
