SilverStone STRIDER TITANIUM SERIES Manuale utente

ST80F-TI / ST70F-TI / ST60F-TI

STRIDER TITANIUM SERIES

World’s smallest 80 PLUS Titanium,

full-modular ATX power supplies

High efficiency with 80 PLUS Titanium certification

Compact design with a depth of 150mm for easy integration

100% modular cables

24/7 continuous power output with 40C operating temperature

Class-leading single +12V rail

Strict ±3% voltage regulation and low ripple & noise

All Japanese capacitors

Ultra silent 120mm fan with 18dBA minimum

The following manual and guides were carefully prepared by the SilverStone engineering team to

help you maximize the potential of your SilverStone product. Please keep this manual for future

reference when upgrading or performing maintenance on your system. A copy of this manual can also

be downloaded from our website at:

Installation and system optimization guide:

AC INPUT

DC OUTPUT

PROTECTION

TIMING

ENVIRONMENT

SAFETY

ELECTROMAGNETIC COMPATIBILITY (EMC)

MTBF

Mechanical Specification

P.1

P.2

P.4

P.5

P.6

P.7

CIICAI

SilverStone Strider Titanium

ST80F-TI

ST70F-TI

ST60F-TI

ATX12V / EPS 12V Switching Power Supply

With Active PFC

80Plus Titanium

PS/2

0

1.1 AC input requirements

The input voltage, current, and frequency requirements for continuous operation are stated below.

Table 1 AC Input Line Requirements

Power factor correction (PF)>0.90 at full load.

The power supply must meet inrush requirements for any rated AC voltage, during turn on at any phase

of AC voltage, during a single cycle AC dropout condition, during repetitive ON/OFF cycling of AC, and

over the specified temperature range (Top). The peak inrush current shall be less than the ratings of its

critical components (including input fuse, bulk rectifiers, and surge limiting device).

This specification describes the requirements of 600,700,800 Watts switching power supply with an stretch

ATX form-factor and EPS 12V, +5V standby voltage ,remote on/off control, full range line input capability

and forced air cooling characteristics.

1. AC INPUT

Parameter

Vin( Full range )

Vin Frequency

Iin(600W)

Iin(700W)

Iin(800W)

Min.

---Nom.

100---240

60-----50

9-----4.5

10------5

11--- 5.5

Max.

264

Unit

VACrms

Arms

2.1 DC voltage regulation

2.2 Load ranges

2.2.1 ST60F-TI Load Range

2.2.2: ST70F-TI Load Range

1.Maximum continuous total DC output power should not exceed 600W.

2.Maximum continuous combined load on +3.3V and +5V outputs shall not exceed 100W.

3.Maximum combined current for the +12V outputs shall be 49A(588W).

4.Peak DC output power should not exceed 650W for 12 second.

1.Maximum continuous total DC output power should not exceed 700W.

2.Maximum continuous combined load on +3.3V and +5V outputs shall not exceed 120W.

3.Maximum combined current for the +12V outputs shall be 58A(696W).

4.Peak DC output power should not exceed 750W for 12 second.

2. DC OUTPUT

Parameter

+3.3V

+5V

+12V

-12V

+5VSB

Range

+/-3％+/-3％+/-3％+/-10％+/-5％Min

+3.20

+4.85

+11.64

-13.20

+4.75

Nom.

+3.30

+5.00

+12.00

-12.00

+5.00

Max

+3.39

+5.15

+12.36

-10.80

+5.25

Unit

Volts

Parameter

+3.3V

+5V

+12V

-12V

+5VSB

Min(optional)

0.1

0.2

0.15

Nom.

Max

0.3

2.5

Peak

　　　　Unit

Amps

Parameter

+3.3V

+5V

+12V

-12V

+5VSB

Min(optional)

0.1

0.2

0.15

Nom.

Max

0.3

2.5

Peak

　　　　Unit

Amps

2.2.3: ST80F-TI Load Range

1.Maximum continuous total DC output power should not exceed 800W.

2.Maximum continuous combined load on +3.3V and +5V outputs shall not exceed 120W.

3.Maximum combined current for the +12V outputs shall be 66A(792W).

4.Peak DC output power should not exceed 850W for 12 second.

Parameter

+3.3V

+5V

+12V

-12V

+5VSB

Min(optional)

0.1

0.2

0.15

Nom.

Max

0.3

2.5

Peak

　　　　Unit

Amps

2.3 Output Ripple

2.3.2 Definition

2.3.3 Ripple voltage test circuit

2.3.1 Ripple regulation

2.4 Overshoot

Any overshoot at turn on or turn off shall be less 10% of the normal voltage value, all

outputs shall be within the regulation limit of section 2.0 before issuing the power good

signal of section 5.0.

2.5 Efficiency

Power supply efficiency typical 10% load/90%, 20% load/92%, 50% load/94%, 100%

load/90% at 115V AC voltage on all outputs.

The ripple voltage of the outputs shall be measured at the pins of the output connector when

terminated in the load impedance specified in figure 1. Ripple and noise are measured at the

connectors with a 0.1uF ceramic capacitor and a 10uF electrolytic capacitor to simulate

system loading. Ripple shall be measured under any condition of line voltage, output load,

line frequency, operation temperature.

Parameter

+3.3V

+5V

+12V

-12V

+5VSB

Ripple&Noise

120

Unit

mVp-p

Figure 1. Ripple voltage test circuit

AC Hot

AC Neutral

Power Supply V out

V return 10uF 0.1uF Load

Scope

AC Ground

2.6 Remote ON/OFF control

3. PROTECTION

3.1 Over current protection

3.2 Over Temperature Protection

The power supply shall have current limit to prevent the +3.3V,+5V,and +12V outputs from

exceeding the values shown in the following Table. If the current limits are exceeded the

power supply shall shutdown and latch off.

The power supply will be protected against over temperature conditions caused by loss of

fan cooling or excessive ambient temperature. In an OTP condition the PSU will shutdown.

When the power supply temperature drops to within specifide limits, the power supply shall

restore power automatically. The OTP circuit temperature drops to within specifide limits,

the power supply shall restore power automatically. The OTP circuit condition.

3.3 Over-power protection

The power supply will be shutdown and latch off when output power within 110~160% of

rated DC output.

Note: Assurance machine can work at low voltage,full load won't damage machine.

3.4 Under voltage protection.

In an under voltage fault occurs, the supply will latch all DC outputs into a shutdown state

when +12V,+5V & +3.3V outputs under 85% of it's maximum value.

ST60F-TI

When the logic level "PS-ON" is low, the DC outputs are to be enabled.

When the logic level is high or open collector, the DC outputs are to be disabled.

Voltage

+12V

+5V

+3.3V

Over Current Limit (Iout limit)

49A minimum; 75A maximum

22A minimum; 45A maximum

ST70F-TI

Voltage

+12V

+5V

+3.3V

Over Current Limit (Iout limit)

58A minimum; 87A maximum

24A minimum; 45A maximum

ST80F-TI

Voltage

+12V

+5V

+3.3V

Over Current Limit (Iout limit)

66A minimum; 95A maximum

24A minimum; 45A maximum

3.5 Over voltage protection

The over voltage sense circuitry and reference shall reside in packages that are separate

and distinct from the regulator control circuity and reference. No single point fault shall be

able to cause a sustained from the regulator control circuity and reference. No single point

fault shall be able to cause a sustained as defined in Table.

3.6 Short circuit

An output short circuit is defined as any output impedance of less than 0.1 ohms. The power

supply shall shut down and latch off for shorting the +3.3 VDC,+5 VDC,or+12 VDC rails to

return or any other rail. Shorts between main output rails and +5VSB shall not cause any

damage to the power supply. The power supply shall either shut down and latch off or fold

back for shorting the negative rails.+5VSB must be capable of being shorted indefinitely,

but when the short is removed, the power supply shall recover automatically or by cycling

PS_ON#. The power supply shall be capable of withstanding a continuous short-circuit to

the output without damage or overstress to the unit

3.7 No load operation

No damage or hazardous condition should occur with all the DC output connectors

disconnected from the load. The power supply may latch into the shutdown state.

Figure 2. is a reference for signal timing for main power connector signals and rails.

Figure 2. PS-OK Timing Sequence

output

+12 VDC

+5 VDC

+3.3 VDC

Minimum

5.5

3.6

Nominal

Maximum

Unit

Volts

4.1 Signal timing drawing

4. TIMING

(1)T3: Power good signal turn on delay time (100ms~500ms)

(2)T2: Rise time(0.1~20ms)

(3)T6: Hold up time (75%Load 16ms)

When the power loss its input power, it shall maintain 16ms in regulation limit at normal

input voltage and 75% full load (AC:115V/60Hz or 230V/50Hz)

The power supply designed to meet UL 60950.

4.2 Hold up time

5.1 Operation

5. ENVIRONMENT

6.1 Underwriters Laboratory (UL) recognition.

6. SAFETY

7.1 ELECTROSTATIC DISCHARGE (ESD) - IEC 61000 – 4 - 2：2008

7.2 ELECTRICAL FAST TRANSIENT / BURST ( EFT/B) – IEC 61000 – 4 - 4：2012

7.3 SURGE – IEC 61000 – 4 - 5：2005

7.4 POWER FREQUENCY MAGNETIC FIELD – IEC 61000 – 4 - 8：2009

7.5 VOLTAGE DIPS – IEC 61000 – 4 - 11：2004

7.6 RADIATED SUSCEPTIBILTY – IEC 61000 – 4 – 3：2006+A1：2007+A2：2010

7.7 CONDUCTED SUSCEPTIBILTY – IEC 61000 – 4 - 6：2008

7.8 VOLTAGE FLUCTATION - EN 61000 – 3 – 3：2008

7. ELECTROMAGNETIC COMPATIBILITY (EMC)

Temperature

Relative Humidity 0 to 40C

10 to 90%, non-condensing

5.2 Shipping and Storage

Temperature

Relative Humidity -20 to 90C

5 to 95%, non-condensing

5.3 Altitude

Operating

Storage 10,000FT max

50,000FT max

7.9 EN61000-3-2：2006+A2：2009 harmonic current emissions.

7.10 EN55022：2010/AC：2011 Class B Radio interference (CISPR 22).

7.11 ANSI C63.4-2009 / FCC Part 15 Subpart B / ICE-003 lssue 5 class B 115VAC

operation.

If applicable to sales in Europe, the power supply shall meet the requirements of

EN 61000-3-2 Class D and the Guidelines for the Suppression of Harmonics in Appliances

and General Use Equipment Class D for harmonic line current content at full-rated power.

The demonstrated MTBF shall be 100,000 hours of continuous operation at 25oC,at 80%

load, and nominal line. The MTBF of the power supply be calculated in accordance with

MIL-HDBK-217F. The DC FAN is not included.

8.1 MTBF (mean time between failures) calculation

8. MTBF

150 mm (W) × 86 mm (H) × 150mm (D)

9.Mechanical Specification

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali SilverStone Alimentazione elettrica

SilverStone

SilverStone ST45SF Manuale utente

SilverStone

SilverStone Gemini GM500-G Manuale utente

SilverStone

SilverStone SFX Series Manuale utente

SilverStone

SilverStone ST55F-G Manuale utente

SilverStone

SilverStone GEMINI Series Manuale utente

SilverStone

SilverStone Lascala Series Manuale utente

SilverStone

SilverStone STRIDER SST-ST60F Manuale utente

SilverStone

SilverStone ST400 STRIDER Manuale utente

SilverStone

SilverStone SST-ST1200-G Manuale utente

SilverStone

SilverStone ST70F-ES Manuale utente

SilverStone

SilverStone STRIDER ESSENTIAL Series Manuale utente

SilverStone

SilverStone GEMINI Series Manuale utente

SilverStone

SilverStone ST50NF Manuale utente

SilverStone

SilverStone ST50F-ES Manuale utente

SilverStone

SilverStone GEMINI GM600-G Manuale utente

SilverStone

SilverStone SST-SX500-LG Manuale utente

SilverStone

SilverStone PSU Manuale utente

SilverStone

SilverStone Decathlon Series Manuale utente

SilverStone

SilverStone STRIDER PLATINUM SERIES Manuale utente

SilverStone

SilverStone STRIDER GOLD S Series Manuale utente

SilverStone

SilverStone GEMINI Series Manuale utente

Manuali Alimentazione elettrica popolari di altre marche

Monacor

Monacor PS-12CCD Manuale utente

VOLTIMA

VOLTIMA MagicBox 15 Manuale utente

Agilent Technologies

Agilent Technologies 6032A Manuale utente

Miller

Miller Auto Deltaweld 452 Manuale utente

BCP

BCP PUOUBK Foglio di istruzioni

HC 2210 Manuale utente

Puls

Puls CT5.241 Manuale utente

OCZ

OCZ ZX1250W Manuale utente

iseg

iseg ECH 238 Manuale utente

Power

Power XXL A Series Manuale utente

Agilent Technologies

Agilent Technologies 6631B Manuale utente

Renogy

Renogy PHOENIX 300 Manuale utente

HP 6200B Manuale di servizio

Epson

Epson Stylus Scan 2500 Manuale operativo

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manuale utente

Puls

Puls MiniLine ML50.100 Manuale utente

Puls

Puls AS-Interface SLA4.100 Manuale utente

Kenwood

Kenwood PS-60 Manuale utente