Simex SRD-99 Manuale utente

Assisting the automation
industry since 1986   
User manual
DATA RECORDER
SRD-99
•Firmware:  .3.34 b1 or higher
•Loggy Soft:  .1.9.0 or higher
•S-Toolkit:  .2.0.23 or higher
Read the user's manual carefully before starting to use the unit or software. 
Producer reserves the right to implement changes without prior notice.
 2016.10.1 SRD- _INSSXEN_v.3.06.005 

User manual - DATA RECORDER SRD-99 and cooperating software
CONTENTS
I. USER MANUAL FOR DATA RECORDER................................................................4
BASIC REQUIREMENTS AND USER SAFETY........................................................................................4
GENERAL CHARACTERISTICS................................................................................................................5
TECHNICAL DATA......................................................................................................................................7
DEVICE INSTALLATION..........................................................................................................................10
1. UNPACKING....................................................................................................................................10
2. ASSEMBLY......................................................................................................................................10
3. CONNECTION METHOD.................................................................................................................13
3.1.Connection  of current type input  ( I ver ion ).......................................................................16
3.2.Connection  of temperature type input   ( RTD ver ion ).......................................................17
4. MAINTENANCE................................................................................................................................18
FRONT PANEL DESCRIPTION................................................................................................................19
 . PRINCIPLE OF OPERATION...................................................................................................................20
1. MEASUREMENT MODE..................................................................................................................20
1.1.Mea urement range  definition of current input  ( I ver ion ).................................................20
1.2.Mea urement range  definition of voltage input  ( U ver ion )...............................................21
1.3.Mea urement range  definition of RTD input  ( RTD ver ion )..............................................21
1.4.Mea urement range  definition of TC input  ( TC ver ion )....................................................22
1.5.Recording momentary and averaged data...............................................................................22
2. MODES OF RESULT PRESENTATION..........................................................................................24
2.1. "Single channel" mode............................................................................................................25
2.2."Mea urement  li t" mode.......................................................................................................26
2.3.”Graph” mode...........................................................................................................................29
2.4.”Channel  Li t” mode...............................................................................................................31
3. PRINCIPLE OF OUTPUTS OPERATION........................................................................................33
3.1.Alarm ......................................................................................................................................33
3.2.Output  control.........................................................................................................................34
3.3.Example of output control........................................................................................................36
DEVICE PROGRAMMING.........................................................................................................................37
1. PARAMETERS EDITION.................................................................................................................39
1.1.Numeric and  witching parameter  ("LIST" - type)..................................................................39
1.2. Text parameter ......................................................................................................................40
1.3.“SLIDER” - type parameter .....................................................................................................41
2. DESCRIPTION OF RESULTS PRESENTATION MODES MENU.................................................42
2.1."Mea urement  li t option " menu...........................................................................................42
2.2.”Graph option ” menu..............................................................................................................43
2.3.”Channel  li t option ” menu....................................................................................................43
3. RESULTS PRESENTATION MODES MENU STRUCTURE..........................................................44
4. MAIN MENU DESCRIPTION...........................................................................................................45
4.1.”Device information” menu.......................................................................................................45
4.2.”Di play option ” menu............................................................................................................45
4.3.”Logging  etup” menu..............................................................................................................46
4.4.“Temperature unit” parameter (RTD ver ion)..........................................................................48
4.5.”Input  etting ” menu (common parameter )...........................................................................49
4.6.”Input  etting ” menu ( I ver ion )............................................................................................50
4.7.”Input  etting ” menu ( U ver ion )...........................................................................................51
4.8.”Input  etting ” menu ( RTD ver ion )......................................................................................53
4.9.”Output   etting ” menu...........................................................................................................54
4.10.”Date & time  etting ” menu..................................................................................................55
4.11.”RS485 port  etting ” menu...................................................................................................56
4.12.”Acce   etup” menu.............................................................................................................57
4.13.”USB option ” menu...............................................................................................................57
4.14.”Language” parameter............................................................................................................58
2

User manual - DATA RECORDER SRD-99 and cooperating software
5. MAIN MENU STRUCTURE..............................................................................................................59
DOWNLOADING DATA FROM DATA LOGGER..................................................................................... 1
1. MODBUS (RS485) DATA DOWNLOAD..........................................................................................61
2. USB FLASH DRIVE (PENDRIVE) DATA DOWNLOAD..................................................................61
THE MODBUS PROTOCOL HANDLING................................................................................................. 4
1. LIST OF REGISTERS......................................................................................................................64
2. TRANSMISSION ERRORS HANDLING..........................................................................................69
3. EXAMPLES OF QUERY/ANSWER FRAMES.................................................................................70
USER'S SETTINGS LIST........................................................................................................................73
II. USER MANUAL FOR “LOGGY SOFT”.................................................................80
GENERAL CHARACTERISTICS..............................................................................................................80
INSTALLATION AND STARTUP..............................................................................................................80
USING THE PROGRAM............................................................................................................................83
1. „CURRENT MEASUREMENT” MENU.............................................................................................84
2. „REPORTS” MENU..........................................................................................................................84
2.1.„Table” tab................................................................................................................................85
2.2.„Graph” tab...............................................................................................................................87
3. „CONFIGURATION” MENU.............................................................................................................92
3.1.„Device ” tab............................................................................................................................93
3.2.„Group ” tab - group operation ...............................................................................................97
3.3.„Setting ” tab............................................................................................................................99
4. LIST OF ERRORS AND FAULT DIAGNOSTICS .........................................................................101
III. USER MANUAL FOR “S-TOOLKIT”..................................................................102
GENERAL CHARACTERISTICS............................................................................................................102
INSTALLATION AND STARTUP............................................................................................................102
USING PROGRAM..................................................................................................................................103
1. “INPUTS SETTINGS” TAB.............................................................................................................104
2. “OUTPUTS SETTINGS” TAB.........................................................................................................105
3. “LOGGING SETUP” TAB...............................................................................................................105
4.  “INTERFACE OPTIONS” TAB......................................................................................................106
5. “DEVICE INFORMATION” TAB.....................................................................................................108
6. CONFIGURATION MODES...........................................................................................................109
6.1.Individual configuration of channel .......................................................................................109
6.2.Configuring  elected channel ...............................................................................................109
6.3.Configuring all channel .........................................................................................................109
7. UPDATING DEVICE FIRMWARE..................................................................................................110
3

User manual - DATA RECORDER SRD-99 and cooperating software

Explanation of symbols used in the manual:

- Thi ymbol denote e pecially important guideline concerning the in tallation and

operation of the device. Not complying with the guideline denoted by thi ymbol

may cau e an accident, damage or equipment de truction.

IF THE DEVICE IS NOT USED ACCORDING TO THE MANUAL THE USER IS

RESPONSIBLE FOR POSSIBLE DAMAGES.

- Thi ymbol denote e pecially important characteri tic of the unit.

Read any information regarding thi ymbol carefully

I. USER MANUAL FOR DATA RECORDER

1. BASIC REQUIREMENTS AND USER SAFETY

- The ma ufacturer is ot respo sible for a y damages caused by

i appropriate i stallatio , ot mai tai i g the proper e viro me tal

co ditio s a d usi g the u it co trary to its assig me t.

- Installation should be conducted by qualified personnel . During installation all

available safety requirements should be considered. The fitter is responsible for

executing the installation according to this manual, local safety and EMC

regulations.

- The unit must be properly set-up, according to the application. Incorrect

configuration can cause defective operation, which can lead to unit damage or

an accident.

- If the device is equipped with PE conntector, it should be connected to PE wire.

- If i the case of a u it malfu ctio there is a risk of a serious threat to the

safety of people or property additio al, i depe de t systems a d

solutio s to preve t such a threat must be used.

- The u it uses da gerous voltage that ca cause a lethal accide t. The u it

must be switched off a d disco ected from the power supply prior to

starti g i stallatio of troubleshooti g (i the case of malfu ctio ).

- Neighbouring and connected equipment must meet the appropriate standards

and regulations concerning safety and be equipped with adequate overvoltage

and interference filters.

- Do ot attempt to disassemble, repair or modify the u it yourself. The u it

has o user serviceable parts. Defective u its must be disco ected a d

submitted for repairs at a authorized service ce tre.

User manual - DATA RECORDER SRD-99 and cooperating software

2. GENERAL CHARACTERISTICS

• Multifunctional

Device is designed for recording, displaying current or averaged values and

presentation of technological parameter trends in graphic form.

• Large data storage capacity

The registered measurement results are recorded in the unit's memory. The

capacity of installed memory allows to store:

–over 500 000 measurements (2MB) for units equipped with RS-485 interface

–over 2 000 000 measurements (8MB) for units equipped with RS-485 interface

and USB Host port.

• Configurable measurement and control input

The unit has up to 8 channels (depending on version) of measurement signals and

one digital voltage input with programmable functions, e.g. control of the recording

process. Each signal can be freely configured and described. Depending on device

version all measured parameters must be available as current type signals

(0-20 mA or 4-20 mA standards) or resistance (Pt100, Pt500 or Pt1000 standards).

The internal analogue-digital converter has a 12 or 16 bit resolution (depending on

input type), which provides high measurement resolution results. Additionally,

individual alphanumeric description (text) of each of the recorded channels is

possible.

• Fast serial interface

The data logger is fitted with a galvanic isolation RS-485 interface, programmed

with ModBus RTU transmission protocol. This enables the connection of a number

of data recorders into the network, remote collecting of data from each unit and also

remote configuration. The application of the RS-485 interface instead of RS-232 is

due to the possibility of achieving high transmission speeds using transmission lines

of larger length than is possible with the RS-232 interface.

• Built-in USB Host interface (optional)

Optionally the device can be equipped with built-in USB Host interface, allowing for

data transfer to popular USB Flash Drives (PenDrives). This method allows for

significant simplification of unit application: it is no longer necessary to connect PC

and data logger via RS-485 interface.

Significant acceleration of data transfer is an additional advantage: data download

can be 10 times faster than using RS-485 interface.

WARNING! Device should work properly with any standard Flash Drives, but

manufacturer can not guarantee proper cooperation with non-standard devices, or

with devices developed after data logger release.

User manual - DATA RECORDER SRD-99 and cooperating software

• Wide range of power supply voltage and external sensor power supply

The built-in pulse power supply allows power to be supplied to the unit with

85...230...260V AC/DC voltage or 16...24...35 AC, 1 ...24...50 DC voltage

(depending on version). Data logger (version with current inputs only) is equipped

with voltage output for powering the sensor and converters: 24V DC ±5% / max.

200mA.

• Legible graphic display

The 128 x 64 points display with a backlight mounted on front of the unit is a big

advantage of the data recorder. It allows the display of trend graphs for each

channel separately. Different operation modes provide the possibility of selecting

and adjusting the method of data presentation depending on the user's

requirements. Data recording intervals are selected by the user from the menu

level. Additionally, it is possible to set the display to show one current value

measured for a selected channel.

• Easy configuration

There are 6 keys on the front of the data recorder that enable the configuration of

the unit. The menu assisted with full text descriptions makes the unit configuration

process quite easy. However, due to a significant number of configured parameters

it is advised to use the attached configuration software for PCs.

User manual - DATA RECORDER SRD-99 and cooperating software

3. TECHNICAL DATA

Power supply voltage

(depending on version)

External Fuse (required)

Power consumption

85...230...260V AC/DC; 50 ÷ 60 Hz (separated)

or 1 ...24...50V DC and 16V...24...35V AC (separated)

T - type, max. 2 A

typically 7 VA; max. 12 VA

Measurement inputs

(depending on version)

I version:

RTD version:

up to 8 inputs 0-20 mA or 4-20 mA, common ground

up to 8 inputs Pt100, Pt500 or Pt1000 type with

automatic connection recognition (2 or 3-wires)

Digital input 1 input 24V DC, galvanic isolation

power consumption: 7,5 mA / 24V,

isolation: 1min @ 500V DC.

Digital outputs 2 electronic relays, NO type, 24V AC / 35V DC /

max. 200 mA, overload protection

Recording cycle 1 sec./ 2 sec. / 5 sec. / 10 sec. / 15 sec. / 20 sec. /

30 sec. /1 min. / 2 min. / 5 min. / 10 min. / 15 min. /

20 min. / 30 min. / 60 min.

Communication interface

Baud rate

RS-485, 8N1 / Modbus RTU, galvanic isolated:

1min @ 500V DC.

1200 bit/s ÷ 115200 bit/s

USB Host interface (optional) Cooperation with standard Flash Disks (USB 2.0)

Display

Data memory

LCD graphic display, 128 x 64 points, with backlight

2MB - version without USB Host

8MB - version with USB Host interface

Protection level

version without USB interface IP 65 (from front, after using waterproof cover)

IP 40 (from front)

IP 20 (housing and connection clips)

version with USB interface IP 54 (from front, after using waterproof cover)

IP 20 (housing and connection clips)

Housing type

Housing material

Housing dimensions

Mounting hole

Assembly depth

Panel thickness

panel

NORYL - GFN2S E1

6 x 6 x 100 mm

0,5 x 0,5 mm

102 mm

max. 5 mm

Operating temperature

Storage temperature

Humidity

Altitude

0°C to +50°C

-10°C to +70°C

5 to 0% no condensation

up to 2000 meters above sea level

Screws tightening max. torque 0,5 Nm

Max. connection leads diameter 2,5 mm2

User manual - DATA RECORDER SRD-99 and cooperating software

Safety requirements according to: PN-EN 61010-1

installation category: II

pollution degree: 2

voltage in relation to ground: 300V AC

insulation resistance: >20MΩ

insulation strength between power supply and

input/output terminal: 1min. @ 2300V (see Fig. 3.1)

EMC PN-EN 61326-1

Device described in this manual is available in two versions differed by

measurement inputs type. This manual contain following short descriptions:

I version - means device with current type inputs (0..20mA / 4..20mA)

RTD version - means device with RTD-type inputs (Pt100 / Pt500 / Pt1000)

Parameters of current type inputs ( I version )

Input type 0-20 mA or 4-20 mA, common ground

Measurement range ± plus decimal point

Current measurement accuracy ± 0.1% @ 25°C; ± one digit (for 0-20 mA range)

Temperature stability 50 ppm / °C

Sampling rate 8 sps

Accepted prolonged input overload 20%

Measurement input resistance 100 Ω

Sensor power supply output 24V DC ± 5% / max. 50 mA,

Not insulated from measurement inputs

Parameters of RTD type inputs ( RTD version )

Input type Pt100, Pt500 or Pt1000 type with automatic

connection recognition (2 or 3-wires)

Measurement range -100°C ÷ +600°C

-148°F ÷ + , °F

Measurement accuracy ± 0.15% @ 25°C; ± one digit

Temperature stability 100 ppm / °C

Sampling rate 1 sample per 2.5 sec

Measurement wires resistance max. 20 Ω (every wire)

Cables connected to RTD inputs can not be longer than 30 meters and must be laid

completely in building.

Software (Window environment)

•S-Toolkit, PC software for data logger easy configuring,

•Loggy Soft, PC software for moving, reporting, archiving and displaying recorded data.

User manual - DATA RECORDER SRD-99 and cooperating software

This is a class A u it. I a reside tial or a similar area it ca cause radio

freque cy i terfere ce. I such cases the user ca be requested to use

appropriate preve tive measures.

Carefully check that the isolation used with the unit (Fig. 3.1) meets the

expectations and if necessary use appropriate measures of overvoltage protection.

Additionally, insure the appropriate air and surface insulation gaps when installing

(Tab. 3.1).

Range of operating voltage Air gap [mm] Surface gap [mm]

Up to 50V RMS or DC 0,2 1,2

Up to 100V RMS or DC 0,2 1,4

Up to 150V RMS or DC 0,5 1,6

Up to 300V RMS or DC 1,5 3,0

Tab. 3.1. Minimal in ulation gap according to EN 61010-1

Fig. 3.1. Schematic diagram howing the in ulation between individual circuit of the unit.

I ter al circuits

relay 2

relay 1

Exter al se sor

supply output

Measureme t i puts RS 485

i terface

Reinforced insulation 1min @ 2300V AC

Supplementary insulation 1min @ 1350V AC

Basic insulation 1min @ 500V AC

No insulation

Relay circuits

Power

supply

User manual - DATA RECORDER SRD-99 and cooperating software

4. DEVICE INSTALLATION

The unit has been designed and manufactured in a way assuring a high level of user

safety and resistance to interference occurring in a typical industrial environment. In order to

take full advantage of these characteristics installation of the unit must be conducted correctly

and according to the local regulations.

- Read the basic safety requirements on page 4 prior to starting the installation.

- Ensure that the power supply network voltage corresponds to the nominal

voltage stated on the unit’s identification label.

- The load must correspond to the requirements listed in the technical data.

- All installation works must be conducted with a disconnected power supply.

- Protecting the power supply connections against unauthorized persons must be

taken into consideration.

4.1. UNPACKING

After removing the unit from the protective packaging, check for transportation damage.

Any transportation damage must be immediately reported to the carrier. Also, write down the

unit serial number located on the housing and report the damage to the manufacturer.

4.2. ASSEMBLY

- The unit is designed for mounting inside housings (control panel, switchboard)

inssuring appropriate protection against surges and interference. Metal housings

must be connected to ground in a way that complies with the governing

regulations.

- Disconnect the power supply prior to starting assembly.

- Check the connections are wired correctly prior to switching the unit on.

In order to install the unit, a 0,5 x 0,5 mm mounting hole (Fig. 4.1) must be

prepared. The thickness of the material of which the panel is made must not exceed

5mm. When preparing the mounting hole take the grooves for catches located on

both sides of the housing into consideration (Fig. 4.1). Place the unit in the

mounting hole inserting it from the front side of the panel, and then fix it using the

brackets (Fig. 4.3). The minimum distances between the center points of multiple

units - due to the thermal and mechanical conditions of operation - are 115 mm x

115 mm (Fig. 4.5).

Altri manuali per SRD-99

Indice

Altri manuali Simex Registratore di dati

Simex

Simex SRD-99 Manuale utente

Simex

Simex SRD-N16 Manuale utente

Simex

Simex SRD-99X Manuale utente

Simex

Simex PMS-90R Manuale utente

Manuali Registratore di dati popolari di altre marche

TESTO

TESTO 176 Manuale utente

HT Italia

HT Italia XL421 Manuale utente

HBM

HBM SOMAT XR CX22B-R Manuale utente

Agtrix

Agtrix 380i Manuale utente

Hobo

Hobo H8 Pro Manuale utente

Beijing ART Tech

Beijing ART Tech PCI2320 Manuale utente

Athena

Athena GET SL1 Manuale utente

Motec Systems

Motec Systems C185 Manuale utente

Beijing ART Tech

Beijing ART Tech USB2832 Manuale utente

Rotronic

Rotronic HygroLog HL20 Manuale utente

MRC

MRC DW-6092 Manuale utente

Racelogic

Racelogic VBOX LapTimer Manuale utente

Edu-Logger

Edu-Logger 900-240 Manuale utente

Elma

Elma DT173 Manuale utente

MadgeTech

MadgeTech PRTemp140 Scheda tecnica

Comet

Comet U0121M Manuale utente

pico Technology

pico Technology PT-104 Manuale utente

Soil Instruments

Soil Instruments GTecLink Manuale utente