Simpnic SiMP PIR-01-SW Manuale utente
Quick Installation Guide
SiMP
Motion Sensor
PIR-01-SW
1. Package Content
2. Get Started
2.1 Preparation
2.2 Installation
2.2.1 Distance
2.2.2 Height
2.2.3 Angle
2.2.4 Sensing Area
2.2.5 Notice
2.3 Power On and Paring
2.4 Reset
3. Basic Settings
3.1 Notification
3.2 Sensitivity
3.3 Recovery Time
4. FAQ
5. Support
1. Package Content
SiMP Motion Sensor (white)
Stand (white)
USB Cable (white)
Adapter (white)
Double-sided Tape (round)
Screws
Quick Installation Guide
Warranty Card
SiMP Motion Sensor can only work with SiMP
Keeper. Please make sure you already have SiMP
Keeper. Otherwise SiMP Remote can’t work.
2. Get Started
2.1 Preparation
Get your SiMPNiC SiMP Keeper ready and
download SiMPNiC App in advance.
To make Motion Sensor work,you need to
set up SiMPNiC SiMP Keeper first.Please
refer to SiMPNiC Smart Home Kit Quick
Installation Guide or tutorial in SiMPNiC App.
You can scan QR code below to download
SiMPNiC App from APP Store (iOS) or
Google Play (Android).
2.2 Installation
Use screws or double-sided tape to make
your SiMP Motion Sensor fixed.We suggest
it to get power from USB cable and adapter,
instead of any kinds of batteries, even
rechargeable ones. If you can only use
batteries,the function of SiMP Motion Sensor
will be limited
2.2.1 Distance
SiMP Motion Sensor can detect any infrared
radiation sources of 9 meters maximum in
straight line. According your need, you can
fix it in the most suitable position of your
house.
2.2.2 Height
The optimal height of SiMP Motion Sensor is 1.6
~1.9 meter from the horizon.
2.2.3 Angle
Make sure the straight line between LED power
indicator and its diagonal point is parallel to
horizon. Please refer to the pictures below.
2.2.4 Sensing Area
SiMP Motion Sensor can detect 100 degree
horizontally and 80 degree vertically. The
sensing area is shown as picture below.
2.2.5 Notice
The height of SiMP Motion Sensor must be
higher than 1.6 meters from the ground. If
it’s lower than 1.6 meters, you can adjust the
vertical angle of SiMP Motion Sensor. The
straight line between LED power indicator and
its diagonal point must be parallel to horizon.
If there are any stains on the surface of SiMP
Motion Sensor, detection will be affected.
Detection will be block by glass or walls.
2.3 Power On and Paring
If your SiMP Motion Sensor is from Home
Kit, it’s already in your SiMPNiC App. You
can tap the "Room"icon at the navigation
bar and then you will see it.
Power on SiMP Motion Sensor, and
you will see the blue LED indicator
blinks rapidly. It lasts about 4 minutes
long. During this time period, it’s
ready for pairing. If it is not blinking,
refer to "Reset" section to make it to
factory default settings.
① Make sure your smartphone is
connected to Home Wi-Fi (2.4GHz).
② Open SiMPNiC App.
③ Select "Room" icon.
④ Select "+" to add device.
⑤ Select "SiMP Motion Sensor".
⑥ SiMP Keeper will beep 2 times and
begin searching. The process lasts
about 45 sec(remember to check
LED indicator is blinking during this
period). And then SiMP Motion
Sensor will appear in the list.
⑦ If SiMP Motion Sensor is not found,
select "Cancel" and search again.
Indice
Altri manuali Simpnic Sensore di sicurezza
