Sinclair SP-300A Manuale utente
SERVICE MANUAL
SP-300A
AIR PURIFIER
Lock Lum
Auto Speed
Turbo Sleep
Anion Odor
Timer
Electrostatic
On/Off
Summary and Features
Main Function Feather:
Silver ion sterilizing anti-mildew
Cold catalyst
HIMOP High efficiency dispel formaldehyde
HEPA High efficiency filtering
Active carbon adsorb hramful gas high efficient
Plasma
Anion
Quiet design
Model SP-300A
P
K
:
G%
P
PP
NJ
9+]
h h
Technical Specifications
Model
Power
Fan Speed Turbo High Low Quiet
Air Flow
Volume
Power
Noise
Surface
Product
Size
Product
Weight
WDH
The surface is the surface influenced by which
the unit runs under high fan speed.
The above data is subject to change without notice. Please refer to the nameplate of the unit.
SP-300A
Filternetzkomponenten
Filter Components
(Cotton filter, HIMOP + HEPA filter components)
Panel
Dust Frame
Activated carbon net rack body
Button
HIMOP net rack
Filter screen
(Activated carbon)
Host display screen
Air inlet
Remote control
On/off
Mode
Odor sensor
Clean/Change
Timer
Running mode
Fan Speed
Lock
Dust sensor
Mute Low High Turbo
Auto Sleep
Anion Odor
Dedust filter
Indicator light
Remote control
receiver window
Dust sensor Odor sensor
On/Off button
Mode button
AIR PURIFIER
Part Name
Unit Parts
Unit display screen
Outline Dimension
Outline Dimension
Unit
Electrical Circuit Diagram
These circuit diagrams are subject to change without notice, please refer to the one supplied with the unit
Model:SP-300A
On/off
Mode
Odor sensor
Clean/Change
Timer
Running mode
Fan Speed
Lock
Dust sensor
Mute Low High Turbo
Auto Sleep
Anion Odor
Dedust filter
Indicator light
Remote control
receiver window
Dust sensor Odor sensor
On/Off button
Mode button
AIR PURIFIER
Controller Function Manual and Operation Method
Manual of Controller Function
1. Basic Function Mode
◆ Auto Mode
The fan speed can be adjusted automatically under auto mode, but if press the FAN key on the remote controller,
the fan speed can not be adjusted. When the auto lamp is light, the corresponding fan speed lamp is light. When the
fan runs with turbo, it will runs with turbo mode, and turbo lamp is light.
When the degree of off-flavor or dust is “low”, the green lamp is light; when the degree of off-flavor or dust is “med”,
the green lamp and orange lamp are light; when the degree of off-flavor or dust is “high”, the green lamp, orange
lamp and red lamp are light.
◆ Turbo Mode
When the plasma is open and anion is close, the fan speed defaults turbo running, the turbo indicator lamp is light,
the fan speed can not be adjusted if press remote controller.
◆ Sleep Mode
The fan speed can be adjusted automatically (low and quiet will change circularly) according to the air quality, the
fan speed can not be adjusted if press remote controller, the sleep indicator lamp is light. The time is clearance
when the unit is off or shift mode.
◆ Anion Mode
When the anion is open and plasma is close, the fan speed defaults low running, the anion indicator lamp is light, the
high, low and quiet can change circularly if pressing FAN key.
◆ Clear off-flavor Mode
When the plasma is open and anion is close, the fan speed defaults high running, the clear off-flavor indicator lamp
is light, the high, low and quiet can change circularly if pressing FAN key.
2 The display function of indicator lamp
◆Operation Mode Lamp: The auto lamp is light under auto mode; the turbo lamp is light under turbo mode; the sleep
lamp is light under sleep mode; the anion lamp is light under anion mode; the anti-off flavor is light under anti-off flavor.
◆Fan speed Lamp: When the high, med, low lamp are light, that means the fan runs with high, med, low fan speed.
◆Timer Lamp: When the timer 1,2,4 lamp are light, that means the timer time is 1h, 2h, 4h respectively; when the unit is
on, the lamp is light shows setting timer is off; when the unit is off, the lamp is light shows setting timer is on, and there is
no timer when the light is dark.
◆Clear/Replace Lamp: When the “clear lamp” is blinking, that means the unit runs 480h totally and remind to clean filter.
The lamp is dark when the conditions are not satisfied or resetting after clean.
When the “clear lamp” is blinking, that means the unit runs 2000h totally and remind to replace HEPA+HIMOP filter. The
lamp is dark when the conditions are not satisfied or resetting after clean.
◆Child Lock/ Dust Induction/ Off-flavor Induction: Controlled by remote controller.
3 Functions of front panel button
There are ON/OFF button and MODE button on the front panel.
a. After the unit is first energized, press ON/OFF when the unit is off, it will run with auto mode, if turn on the unit again
it will run with the previous mode, the unit is off if pressing ON/OFF when the unit is on.
b. Press MODE when the unit is on, it will choose circularly by auto->turbo->sleep->anion->clear off-flavor->auto, and
the fan speed runs with default fan speed of each mode.
c. When the unit is stand-by, press mode key for 5S, all the indicator lamps are light and buzzer gives out beep, the
cumulate time is clearance.
Note: When the unit runs 0.5h, the time cumulates one time, and no cumulation if runs less than 0.5h. The corresponding
indicator lamp blinks to remind customer clean or replace it when the total cumulate time reaches. Before the cumulate
time haven’t been cleared, the indicator blinks if re-energized. If both cumulate time of clean and replace do not reach,
they are clearance after resetting (used for factory-zero clearing), if one cumulate time reaches, only clear it after
resetting, the other continues to run; if both of them reach, clear them after resetting.
4 Function of remote control button
◆ON/OFF: After the unit is first energized, press ON/OFF when the unit is off, it will run with auto mode, if turn on the
unit again it will run with the previous mode, the unit is off if pressing ON/OFF when the unit is on.
◆Child Lock: Press it for 2S, the unit runs under this mode; it will be cancelled for 2 ways: lock function key with remote
controller (press for 2S) or the unit is power-fail.
◆Six mode keys: There are below modes: auto, turbo, sleep, anion, clear off-flavor. The button is valid when the unit is
on.
a. If the current modes are auto, sleep and turbo, it will shift to the default status of this mode if pressing anion and anti
off-flavor. If the current modes are anion and anti off-flavor, press the mode key which the same as the current mode, the
buzzer gives out beep and no action for controller.
b. If the current mode is DUST:
Enter anion mode if press anion button, and default the status operation if press anion mode.
Enter clear off-flavor mode if press off-flavor button, and default the status operation if press clear off-flavor mode.
There is no change if press dedust button.
c. If the current mode is anion: Enter clear off-flavor mode if press off-flavor button, and default the status operation if
press clear off-flavor mode. There is no change if press anion/static dedust button.
d. If the current mode is clear off-flavor: Enter anion mode if press anion button, and default the status operation if press
anion mode. There is no change if press clear off-flavor /static dedust button.
◆Timer Key: The unit will choose circularly by timer 1h->2h->4h->cancel if press this button.
Press timer if the unit is off, that means set timer on; press timer if the unit is on, that means set timer off. Eg: set the
current timer to turn off the unit 1h later, then repress it is to turn off the unit 2h later, and then repress is to turn off the
unit 4h later, last press it is cancel it. Then press it is to turn off the unit 1h later, cycle like this.
Note: If the current setting timer is 1h and does not reach, presses TIMER, the timer time will update to2h, and restart to
time regarding 2h.
If the unit is on and is set timer time off already, receiving the signal to turn off the unit, the unit is off and clears timer
information.
If the unit is off and is set timer time on already, receiving the signal to turn on the unit, the unit is on and clears timer
information.
◆Fan Key: It cycles by quiet->low speed->high speed (It is invalid with stand-by, auto, sleep and turbo mode). The fan
speed runs with initial fan speed of each model when shift mode by remote control.
◆Setting Key: The brightness of indicator lamp will be adjusted per press, the dust induction lamp and off-flavor
induction lamp will display circularly by bright->dark->go out, and other lamps will display circularly by
bright->dark->dark->bright.
On/Off
ƽ
On/Off button
Speed button
ƽ
High Low
6peed
TimHUbutton
ƽ
TimHU
ƽ
Remote control
Mute
Turbo button
ƽ
Turbo
˄ hour˅
˄hour˅
˄hour˅
Cancel
Ć
You can change the IDQspeed through the speed button.
Anion
ƽ
Anion button
Ć
Auto
ƽ
Auto button
Ć
ƽ
Ć
Sleep
Sleep button
Odor
Odor button
The perfect functional regulation need to be completed by remote control.
Ć
Electrostatic
ƽ
The button is invalid on this machine.
Electrostatic cleaning
Lock Lum
Auto Speed
Turbo Sleep
Anion Odor
Timer
Electrostatic
On/Off
If it in power state, every time you press the
button, the timing will change according to
the following sequence. And the timing light
of host computer will flash accordingly, then
you can you can select the time.
Note: when it is at power on, the timing is for
timed shutdown; when it at power off, the timing
is for timed power on.
When it is in running state, click the button,
the machine will be in this mode. The
plasma opens, and the IDQwill run at the
highest speed.
When it is in running state, click the button,
the machine will be in this mode. The
negative ion opens, and the IDQwill run at
low speed.
You can change the IDQspeed through the speed button.
When it is in running state, click the button.
The machine automatically adjust mute
IDQspeed or low speed according to air
quality.
In this mode, the "speed" button is invalid.
When it is in running state, click the button.
The machine automatically adjust the on/off
switch of plasma according to air quality.
In this mode, the "speed" button is invalid.
Click the button when it is in standby mode,
and the machine will begin to run. If you
press it again, the machine will stop running.
When it is in running state, IDQspeed will
switch according to the following sequence.
And the speed light of host computer will
flash, then you can select the IDQ speed.
When it is in running state, click the button
and the machine will be in this mode.
Plasma opens, and the IDQruns in ultra-
high speed.
High air-flow can quickly remove dust in the
air, and it is easy to use in cleaning the air.
Names and Functions of Remote Control Buttons
Altri manuali per SP-300A
1
Indice
Altri manuali Sinclair Purificatore d'aria
