Singer 5040 Manuale utente
Instruction Manual
Contents
For European territories
Important safety instructions
Getting to know your machine
Principal parts
Accessories
Connecting the machine
Running the machine
Choosing and changing needles
Changing the needle plate
Changing screw-on presser feet
Attaching the feed cover
Changing snap-on presser feet
Fabric, thread and needle table
Inserting a bobbin
Winding a bobbin
Threading the machine
Raising the bobbin thread
Adjusting thread tension
Sewing a seam
Starting a seam
Straight stitching
Stitch width selector
Needle position selector
Stitch length selector
Reverse stitch button and sewing in reverse
Darning
Inserting a zipper
Zig-zag stitching
Needle position selector
Stitch width selector
Adjusting stitch length
Pattern groups selection
Flexi-stitch patterns
Balancing flexi-stitches
Pattern stitching
Removing and replacing pattern module
Decorative stitch patterns
Flexi-stitch patterns
Attaching a button
Free arm sewing
Removing the extension table
Four step buttonhole
Twin needle sewing
Additional accessories / Accessory storage
Caring for your machine
Removing and replacing bobbin case
Cleaning the machine
Lubricating the machine
Changing the light bulb
Performance checklist
3
IMPORTANT SAFETY INSTRUCTIONS
When using this machine, basic safety pre-
cautions should always be followed including
the following:
Read all instructions before using this
machine.
DANGER
To reduce the risk of electric shock:
• The machine should never be left unattend-
ed when plugged in. Always unplug the
machine from the electric outlet immediately
after using and before cleaning.
• Always unplug before relamping. Replace
bulb with the same type rated 15 watts. Be
sure to replace the face plate which covers
the light bulb before operating the machine.
WARNING
To reduce the risk of burns, fire, electric
shock or injury to persons:
• Be sure that the electrical voltage of the
socket outlet (wall receptacle) is the same
as the rated voltage of the motor.
• Use this machine only for its intended use
as described in this Operator's Guide. Use
only attachments recommended by the
manufacturer as contained in the Operator's
Guide.
• To disconnect, turn all controls to the off
("0") position, then remove plug from outlet.
Dear Customer,
We recommend that for future reference you
record the Serial Number of your Sewing
Machine in the space provided.
Refer to illustration for location of Serial
Number on your machine.
4
WARNING continued...
•Disconnect the power-line plug from the
socket outlet or switch the machine off when
making any adjustments in the needle area,
such as threading needle, changing needle,
changing throat plate or changing presser
foot, etc.
•Always unplug the machine from the electri-
cal outlet when removing covers, lubricating,
or when making any other user servicing
adjustments mentioned in the Operator's
Guide.
•Do not attempt to adjust the motor belt.
Contact your nearest Service Center should
any adjustment be required.
• Do not unplug by pulling on cord. To unplug,
grasp the plug, not the cord.
• Handle the foot controller with care and
avoid dropping it on the floor. Be sure not to
place anything on top of it.
•Always use the proper throat plate. The
wrong plate can cause the needle to break.
• Do not use bent needles.
• When sewing, keep fingers away from all
moving parts. Special care is required
around the sewing machine needle.
• Do not pull or push fabric while stitching. It
may deflect the needle causing it to break.
• Before removing the bobbin case, remove
plug from the socket outlet.
• For double insulated machines, when serv-
icing use only identical replacement parts.
• Never operate the machine if it has a dam-
aged cord or plug, if it is not working proper-
ly, if It has been dropped or damaged, or
dropped into the water. Return the machine
to the nearest authorized dealer or Service
Center for examination, repair, electrical, or
mechanical adjustment.
•Never operate the machine with any air
openings blocked. Keep ventilation open-
ings of the machine and foot controller free
from the accumulation of lint, dust, and
loose cloth.
•Never drop or insert any object into any
opening.
5
Neither core is to be connected to the earth
terminal of a three-pin plug.
• Do not use outdoors
• Do not operate where aerosol (spray) prod-
ucts are being used or where oxygen is
being administered.
•Do not allow to be used as a toy. Close
attention is necessary when the machine is
used by or near children.
For European Territories:
This product is suppressed for radio and tele-
vision interference with the International
Electrotechnical Commission requirements of
the CISPR.
Machines for Great Britain:
Machines for Great Britain and some other
countries having similar wiring standards are
shipped from the factory without a plug for
connection to the mains. The wires in this
mains lead are coloured in accordance with
the following code:
Blue: neutral (N) Brown: live (L)
As the colours of the wires in the mains lead
of this appliance may not correspond with the
coloured markings identifying the terminals in
your plug, proceed as follows:
The wire, which is coloured blue must be
connected to the terminal which is marked
with the letter N or coloured black. The wire,
which is coloured brown must be connected
to the terminal which is marked with letter L
or coloured red. If a 13 Amp. (BS 1363) plug
is used, a 3 Amp. fuse must be fitted, or if
any other type of plug is used, a 5 Amp. fuse
must be fitted either in the plug or adapter or
at the distribution board.
SAVE THESE INSTRUCTIONS
Servicing should be performed
by an authorized service representative.
This product is intended for household use.
6
Principal parts
1. Hand wheel
2. Bobbin winder
3. Horizontal spool pin and holder
4. Top cover lid
5. Thread guide
6. Bobbin winder tension disc
7. Snap-in thread guide
8. Take up lever
9. Face plate
10. Needle thread tension dial
11. Accessory storage
12. Snap on presser foot
13. Needle plate
14. Removable extension table
15. One-way needle clamp
16. Thread guides
17. Push button reverse
18. Stitch length dial/four-step buttonhole
19. Stitch width lever
20. Pattern selector dial
21. Needle position selector
22. Stitch balance control
23. Presser foot lifter
24. Thread cutter
25. Feed system
26. Slide plate
27. Foot control
28. Electrical lead
29. Machine plug
30. Power and light switch
31. Bobbin winding indent
Getting to know your machine
7
8
Accessories
The following accessories furnished with your
sewing machine are designed to simplify your
sewing projects and increase the versatility of
your machine.
The letter in a circle adjacent to the illustrated
part is reproduced on the part itself to help
you select the correct attachment for the type
of work you are doing.
1. Interchangeable pattern module.
2. Special purpose presser foot (J) is used
for decorative and zig-zag sewing.
3. General purpose needle plate (A) and
presser foot (B) are on your machine
when delivered. Use together for alternat-
ing between straight and zig-zag stitching.
4. Buttonhole presser foot (L) is used with
the General Purpose Needle Plate to make
four-step buttonholes
5. Zipper foot (E) is used for inserting zip-
pers and stitching corded seams.
6. Friction free spool holder is used to hold
various size spools and allows thread to
unwind smoothly. The spool does not turn.
7. Small thread spool holder (Q) for use
with small diameter spools of thread.
8. Needlepack includes an assortment for
sewing various types of fabrics.
9. Feed cover (F) is used to prevent the feed
from moving the fabric when darning or
free motion embroidery.
10. Transparent bobbins for easy viewing of
thread supply.
11. Blindstitch hem presser foot is used to
position the hem for blindstitch hemming.
9
Connecting the machine
Push plug into the receptacle (1) at the right
end of the machine. Then connect plug (2) to
your socket outlet.
10
Running the machine
To turn on machine and sewing light, press
upper portion of power switch. To turn off
machine and light, press lower portion "O" of
power switch.
To run the machine and control speed, press
the foot control with your foot. The harder you
press, the faster the machine will sew. To
stop machine, remove foot from control.
Note: Do not operate machine without fabric
under the presser foot as this may
damage the feed and the presser foot.
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Singer Macchina da cucire
Singer
Singer 33-51 Guida rapida
Singer
Singer 400W101 Guida rapida
Singer
Singer HD0400S Manuale utente
Singer
Singer 71-142 Manuale utente
Singer
Singer QUANTUM STYLIST 9960 Manuale utente
Singer
Singer 410W10 Manuale utente
Singer
Singer 1669U Manuale utente
Singer
Singer 251-21 Manuale utente
Singer
Singer Start Manuale utente
Singer
Singer 136W104 Manuale utente
Singer
Singer 24-70 Manuale utente
Singer
Singer Heavy Duty 4452 Manuale utente
Singer
Singer 247-4 Manuale utente
Singer
Singer merritt 2404 Manuale utente
Singer
Singer RD51 Manuale utente
Singer
Singer C5105 Manuale utente
Singer
Singer 477 Manuale di installazione e funzionamento
Singer
Singer 51W44 Manuale di installazione e funzionamento
Singer
Singer VS1 Guida
Singer
Singer Promise 1512 Manuale del proprietario
