Singer MT624 Manuale utente

Questo manuale è adatto per i seguenti modelli

1

Altri manuali Singer Macchina da cucire

Singer

Singer 71-30 Guida rapida

Singer

Singer 221 Manuale di installazione e funzionamento

Singer

Singer 157-3 Guida rapida

Singer

Singer 61w34 Manuale utente

Singer

Singer 98-3 Manuale utente

Singer

Singer 2639 Manuale utente

Singer

Singer ST-1 Manuale utente

Singer

Singer Sewing Machine Manuale utente

Singer

Singer 176-35 Guida rapida

Singer

Singer 484.1544180 Manuale utente

Singer

Singer 354 Manuale utente

Singer

Singer 211G155 Manuale utente

Singer

Singer 144W204 Guida rapida

Singer

Singer 431D 200A Manuale utente

Singer

Singer 212U443A Guida all'installazione

Singer

Singer 211U157 Manuale utente

Singer

Singer 152-1 Guida rapida

Singer

Singer 246-13 Manuale di installazione e funzionamento

Singer

Singer 301-1 Manuale utente

Singer

Singer 245-4 Guida rapida

Singer

Singer 18U322 Manuale utente

Singer

Singer 52-54 Manuale utente

Singer

Singer 147-1 Manuale utente

Singer

Singer 6660 Manuale utente

Manuali Macchina da cucire popolari di altre marche

Riccar

Riccar RL634DE Manuale utente

Pfaff

Pfaff 3307-1 SERIES Manuale utente

Janome

Janome Quilt Maker Pro 18 VERSA Manuale utente

Siruba

Siruba C007JP Manuale utente

Husqvarna Viking

Husqvarna Viking Designer SE Manuale utente

IKEA

IKEA SY Manuale utente

Pfaff

Pfaff 571 Manuale utente

Brother

Brother BB370 Manuale utente

Pegasus

Pegasus WT100 Series Manuale utente

Reliable

Reliable 7100DB Manuale utente

Pfaff

Pfaff 937 Manuale utente

Pfaff

Pfaff 1471 E1 Manuale utente

Kenmore

Kenmore 16677 - Serger Sewing Machine Manuale utente

HIGHLEAD

HIGHLEAD GC2008-M Manuale utente

Brother

Brother BE-1204C Manuale utente

JUKI

JUKI MO-104 Manuale utente

Bernina

Bernina Quilting Frame Manuale utente

Brother

Brother 885-V14 Manuale utente

P a g e 1 of 8, V1

SuperbaKnit interface electronic hardware exchange for MT624 & 9000

The picture below shows the Singer MT624 knitting machine.

Place the bed on a table or workbench with the right end hanging free to give access to

the bottom.

P a g e 2 of 8, V1

Remove the screw that holds the small plastic cover piece

P a g e 3 of 8, V1

Slide the cover to the right and remove it completely.

P a g e 4 of 8, V1

After removal of the plastic cover, your machine will look similar to the picture

above.

P a g e 5 of 8, V1

Remove the printed circuit board from the connector.

P a g e 6 of 8, V1

The MT 624 after removal of the PCB.

Now you have to cut the red wire that comes from somewhere under the metal belt,

and runs either to the black connector, or disappears in the cable sleeve whit the

other 4 visible wires.

P a g e 7 of 8, V1

Make sure you do not cut a second red wire that runs from the connector into the

cable sleeve. If the red wire goes to the connector, cut the red wire close to the

connector. If the red wire goes into the cable sleeve, cut the red wire where the red

wire enters the cable sleeve. This gives the maximum length for this piece of wiring.

Then enter this lose end of red wire in the clamp connector. No need to remove

insulation. Put it right in the middle and then snap together the clamp. It usually

needs no tools, just your fingers, to close the clamp.

The result should look as above.

P a g e 8 of 8, V1

Attach the connector at the end on the header in the middle of the new pc board,

and insert the pc board into the black connector. Center the contacts well and make

sure the board is inserted to its maximum position.

It should look now as above.

Now you have to adjust the 2 potentiometers that control the optical sensor

sensitivity. For instructions, please consult the “SuperbaKnit Interface A

Adjustments” document.

Place back the plastic end cover of the bed just in the reversed way as you removed

the cover, and secure the cover with the screw from the bottom side.