Singer XL-420 Manuale utente

Service Manual

Original issue

May 2014

Page 1／64

Model

XL-420

| 1

XL-420

First issue: May, 2014

Service Manual

Original issue

May 2014

Page 2／64

Model

XL-420

| 2

SEC.1 Disassembling covers

SEC.2 Test mode with warning function deactivated

SEC.3 Needle clearance to shuttle

SEC.4 Alignment of needle plate to shuttle

SEC.5 Presser foot height and direction

SEC.6 Origin point positioning of zigzag bight

SEC.7 Needle bar height

SEC.8 Needle threader height

SEC.9 Adjustment of feed dog height

SEC.10 Tension of timing belt

SEC.11 Needle timing to feed dog

SEC.12 Needle timing to shuttle hook

SEC.13 Adjustment of timing of take-up lever to shuttle

SEC.14 Adjustment of meshing position of gears for take-up lever

SEC.15 Retaining bracket for bobbin case

SEC.16 Origin point positioning of feed “zero”

SEC.17 Stitch length

SEC.18 Ajustment of upper thread tension

SEC.19 Adjustment of CAM sensor

SEC.20 Check the Knee Lifter

SEC.21 Sewing machine test mode

SEC.22 Removing top cover and carriage cover of embroidery unit

SEC.23 Adjustment of stop position of embroidery carriage

along X & Y axis

SEC.24 Embroidery unit test mode

SEC.25 Trouble contents with LED on panel

SEC.26 Wiring diagram part1 & part2

SEC.27 Main circuit board and functions of each connector

Contents

Service Manual

Original issue

May 2014

Page 3／64

Model

XL-420

| 3

Ａ．Disassembling face cover

Ｂ．Disassembling bed cover

1. Pull out cap (not shown) in the center

and remove screw.

2. Loosen the screw behind.

3. Remove face cover

1. Pull out cap at bed cover using needle.

SEC.1-1 Disassemblin

covers

(

)

Service Manual

Original issue

May 2014

Page 4／64

Model

XL-420

| 4

Ｃ．Disassembling bobbin winder unit.

2. Loosen M4 screw.

3. Slide out bed cover.

1. Remove M3 screw at bobbin winding

latch.

2. Remove bobbin winding latch.

SEC.1-2 Disassembling covers (2)

Service Manual

Original issue

May 2014

Page 5／64

Model

XL-420

| 5

Ｄ．Removing switch cover

3. Remove M4 screw at bobbin winder

cover.

4. Remove two hooks at the side of the cover

from rear cover.

１．Removing M4 screws at the side of the cover.

SEC.1-3 Disassembling covers (3)

Service Manual

Original issue

May 2014

Page 6／64

Model

XL-420

| 6

Ｅ．Removing base cover

２．Remove switch cover.

１．Remove three M4 screws behind the sewing machine.

２．Lay the machine and remove two M3 tapping screws.

SEC.1-4 Disassembling covers (4)

Service Manual

Original issue

May 2014

Page 7／64

Model

XL-420

| 7

Ｆ．Remove front and rear covers.

３．Remove two M4 screws on the right.

４．Remove two M4 screws on the center.

1. Remove two M4 tapping screws near the handle at the top of rear

cover.

SEC.1-5 Disassembling covers (5)

Service Manual

Original issue

May 2014

Page 8／64

Model

XL-420

| 8

４． Lay the machine and open a rid behind the front cover by using a

small screw driver.

3. Remove M3 screw and washer at the front cover.

You can only loosen a screw but if you do so, be careful of a

position of washer when re-assembling.

2. Remove M4 screw at rear cover.

SEC.1-6 Disassembling covers (6)

Service Manual

Original issue

May 2014

Page 9／64

Model

XL-420

| 9

5. Insert small screw driver into clearance

between front and rear covers and then lift up the

front cover to remove two covers as shown at left.

* Once hooked portions A, B and C as shown

above are removed, other mating portions may be

removed easily.

ＡＢ

Ｃ

6. Lay the machine on its back for easier removal

of covers. Remove front cover. Remove CPU

board and FFC-28 from front cover with care.

*FFC is flexible flat cable

SEC.1-7 Disassembling covers (7)

Ｂ

Ｃ

Service Manual

Original issue

May 2014

Page 10／64

Model

XL-420

| 10

7. Lower the presser foot lever and

then remove rear cover by lifting up

and passing it under the presser foot

taking care not to interfere with each

other.

This is a view of machine without front

cover.

This is a view of machine without

rear cover.

SEC.1-8 Disassemblin

covers

(

)

Altri manuali per XL-420

Altri manuali Singer Macchina da cucire

Singer

Singer 791D100A Manuale utente

Singer

Singer CLASS 20 Manuale utente

Singer

Singer 221-1 Manuale utente

Singer

Singer CONFIDENCE 7470 Manuale utente

Singer

Singer FUTURA CE-150 Manuale utente

Singer

Singer QUANTUM L-500 Manuale utente

Singer

Singer 4830 Manuale utente

Singer

Singer MA75T Manuale utente

Singer

Singer 6038 Guida del prodotto

Singer

Singer 457 G 130 Guida all'installazione

Singer

Singer 81-50 Manuale utente

Singer

Singer 132W100 Manuale utente

Singer

Singer M1250 Manuale utente

Singer

Singer 8770 CURVY Manuale del proprietario

Singer

Singer 14U134 Manuale

Singer

Singer 348K Manuale utente

Singer

Singer 2932 Manuale utente

Singer

Singer 5838 Manuale utente

Singer

Singer 6010 Manuale utente

Singer

Singer 251-4 Manuale utente

Singer

Singer 221K1 Manuale di installazione e funzionamento

Singer

Singer 569U Guida all'installazione

Singer

Singer 650 Manuale utente

Singer

Singer featherweight 132 Manuale utente

Manuali Macchina da cucire popolari di altre marche

Riccar

Riccar RL634DE Manuale utente

Pfaff

Pfaff 3307-1 SERIES Manuale utente

Janome

Janome Quilt Maker Pro 18 VERSA Manuale utente

Siruba

Siruba C007JP Manuale utente

Husqvarna Viking

Husqvarna Viking Designer SE Manuale utente

IKEA

IKEA SY Manuale utente

Pfaff

Pfaff 571 Manuale utente

Brother

Brother BB370 Manuale utente

Pegasus

Pegasus WT100 Series Manuale utente

Reliable

Reliable 7100DB Manuale utente

Pfaff

Pfaff 937 Manuale utente

Pfaff

Pfaff 1471 E1 Manuale utente

Kenmore

Kenmore 16677 - Serger Sewing Machine Manuale utente

HIGHLEAD

HIGHLEAD GC2008-M Manuale utente

Brother

Brother BE-1204C Manuale utente

JUKI

JUKI MO-104 Manuale utente

Bernina

Bernina Quilting Frame Manuale utente

Brother

Brother 885-V14 Manuale utente