SIRCHIE BLUEMAXX BM500LED Manuale
Technical Information TI02ENG124R9
100 HUNTER PLACE, YOUNGSVILLE, NC 27596 USA
Ph: (919) 554-2244, (800) 356-7311 • Fax: (919) 554-2266, (800) 899-8181
BLUEMAXXTM Rechargeable Forensic LED Light
BM500LED
Background and Purpose
The BLUEMAXX™ BM500LED is a rechargeable LED-based illuminator which emits high
intensity blue light at 455nm (nanometers). This wavelength can produce fluorescence in
physiological fluids and other materials treated with certain powders and dyes; in general,
materials having optical excitation bands between 390 and 520nm.
The kit has a pair of orange goggles that effectively filters the blue light, permitting visual
observation and photography of the fluorescence effect. The light is an essential tool for
area searches and photography of evidence at a crime scene, and provides best results
when used under subdued ambient lighting conditions.
Technical Information TI02ENG124R9
100 HUNTER PLACE, YOUNGSVILLE, NC 27596 USA
Ph: (919) 554-2244, (800) 356-7311 • Fax: (919) 554-2266, (800) 899-8181
Unpacking / Set-up
Next unthread (rotate counter-clockwise) the tail cap from the body tube and install the
battery pack with the Positive (+) terminal of the pack (the raised “bump”) facing toward
the head-end of the light. Then fasten the tail cap by threading it (rotate clockwise) into the
body tube (shown below).
FIG 1: Battery Installation
Safety Precautions
CAUTION: Due to the intensity of the light, do not look directly into the beam.
Reversing the battery may permanently damage the flashlight and the battery pack.
Electrical Info
Battery: 6volt, 3.5 amp-Hr nickel metal hydride (Ni-Mh) battery pack
Switch: Recessed, push-on –push-off soft touch button
Illuminator: High output LED
Charger: Input : Universal voltage 100-240VAC, 50/60Hz, Output: 12VDC
Charge Rate: 220 –400 mA (typical)
Charge Time: Completely discharged battery : 12-16 hrs
Light Operation
The ON-OFF button is located at the base of the head cap. Press for ON. Press again for OFF.
Beam Adjustment
The head of the flashlight can be rotated slightly left or right in order to achieve the best
beam pattern for your use.
Charger Operation
The Charger Cradle may be used free-standing or permanently mounted to a surface, such
as a desk, wall or in a vehicle. Recessed mounting holes inside the cradle accept up to #8
mounting screws, which should be a minimum of 1 inch (25mm) long.
+
Technical Information TI02ENG124R9
100 HUNTER PLACE, YOUNGSVILLE, NC 27596 USA
Ph: (919) 554-2244, (800) 356-7311 • Fax: (919) 554-2266, (800) 899-8181
Insert the Charger Plug head into its port at the front of the Cradle. Align the charge rings of
the light with contacts in the cradle and snap the BLUEMAXX into the Charging Cradle. The
Retainer Tabs will hold the light securely. The Contact Rings on the flashlight body will now
be touching the metallic Charging Contacts in the bottom of the Cradle, allowing the battery
to charge. To remove the light from the Charging Cradle, press the red release button then
lift the light straight up and out.
FIG 2: Charging Cradle Features FIG 3: Light Installed in Charging Cradle
Plug the universal power supply into a wall socket: domestic: 100-125VAC or international:
208-240VAC (using the supplied adapter on the power supply AC contact blades).
FIG 4: Power Supply –Domestic FIG 5: With International adapter blade
While charging, the Charging Indicator (on the top edge of the Charge Cradle) will be
red/orange. When the charge is complete, the Charging Indicator will be green.
CAUTIONS: While charging, do not let any conductive objects touch the Contact Rings on the
body of the flashlight. Only charge your BM500LED when the battery has completely
discharged (charging time in this case will be 12 - 16 hours). Do not store your BM500LED in
the charging cradle between uses as it will shorten the life of your battery pack.
Technical Information TI02ENG124R9
100 HUNTER PLACE, YOUNGSVILLE, NC 27596 USA
Ph: (919) 554-2244, (800) 356-7311 • Fax: (919) 554-2266, (800) 899-8181
Cleaning and Maintenance
If the flashlight front cover filter becomes foggy or dirty, clean with a lens specific cloth
only. Do not use cleaners or water, as they will damage the filter coating. If the filter is
damaged or broken, please contact Sirchie Customer Service to order a replacement
Technical Specifications
•Illuminator: High output white LED with blue narrow-band 455nm filter cover glass
•Reflector: Parabolic, calibrated for 8"-10" (20.3cm - 25.4cm) spot at 10' (3m)
•Beam Pattern: Adjustable with 1/8 turn of head
•Construction: Rugged machined aluminum w/knurled grip, anodized inside and out
(corrosion, water, and shock resistant)
•ON-OFF Switch: Recessed, push-button (push ON, push OFF)
•Battery: Rechargeable 6 volt at 3.5 amp-Hr, nickel metal hydride (Ni-Mh) battery pack.
•Flashlight Length: 12.6" (32cm); Weight w/Battery pack: 32 oz. (907.2g)
•Light filter: Blue Additive Dichroic, T(ave)=60% (+/-7.5%) 380-480nm
T=50% @ 490nm(+/-10nm) T(ave)<1% 520-780nm
•Set of orange filter goggles
•Charger Cradle: Black ABS plastic “cradle/clamp” type
•Charger Power Supply: Universal voltage input 100 –240VAC (with adapter blade for
International operation), 50/60Hz; Output 12VDC @ 450mA
•Charging Contact: 360-degree positive contact around flashlight body
•Charging Indicator: Bi-color LED: red = charging, green = charge complete
•Charging Rate: 220 –400 mA (typical); Charging Time: 12 - 16 hrs (fully discharged battery)
Trouble Shooting Guidelines
Symptom(s)
Possible Cause(s)
Remedy Action(s)
No illumination
Battery missing
Install battery
Battery installed backward
Re-install observing correct polarity
Battery discharged
Charge battery
Battery defective
Contact Sirchie Customer Service
Switch defective
LED defective/burned out
Front cover filter opaque/damaged
Flashlight damaged internally
White light emitted
Blue filter missing/damaged
Replace blue dichroic filter
Indice
Altri manuali SIRCHIE Torcia elettrica
