SITRONICS INTRACOM omniBAS Manuale utente

Next Generation Ethernet

Microwave Backhaul Solution

Installation and

Cabling Manual

Edition 6.0

GDC-002/34

Confidential

INTRACOM TELECOM

19.7 km Markopoulou Ave., Peania, Athens, GR 19002

T +30 210 667 1000, F +30 210 667 1001

http://www.intracom-telecom.com

email (product support): omnibas_support@intracom.com

The information contained in this document is subject to change without prior notice.

All copyright, intellectual and industrial rights in this document and in the technical knowledge it contains

are owned by INTRACOM S.A. TELECOM SOLUTIONS and/or their respective owners.

This document is made available to the end users only for their internal use.

No part of this document nor any data herein may be published, disclosed, copied, reproduced,

redistributed by any form or means, electronically or mechanically, or used for any other purpose

whatsoever without the prior written approval of INTRACOM S.A. TELECOM SOLUTIONS.

Information as well as drawings and specifications contained in this document are subject to change

without prior notice.

All trademarks and copyrights mentioned herein are the property of INTRACOM S.A. TELECOM

SOLUTIONS and/or their respective owners.

Any rights not expressly granted herein are reserved.

Printed in Greece.

Document Revision History OmniBAS -2W/4W/8W

Installation and Cabling Manual - Edition 6.0

Document Revision History

Revisions This page shows the main changes effected in relation to the previous

edition of the OmniBASTM IDU Installation:

Revisions

Previous: 4.0 – 5.1

Current: 6.0

Reasons of

change

The table below shows the reasons for the document change effected in

relation to the previous document edition.

Chapter /

Paragraph

A (Added),

M (Modified) or

R (Removed)

Introduction

Overview of OmniBAS Product Family (page 2):

•New unit added (OmniBASTM-4P).

•New unit for OmniBASTM-4W.

M / A

Installation Material

Installation materials for OmniBAS-4W/8W (page 10). M

New installation materials for new unit OmniBAS-4P (page 14). A

Before Starting the Installation

New Power supply requirements (page 17) for new units OmniBASTM-

4W/4P.

M / A

New Cabling Overview (page 20) for all units. M

Mechanical Installation

New Chassis Overview (page 34) for new unit OmniBASTM-4W. M

New unit added OmniBAS-4P (page 39). A

Cabling Installation

New unit added OmniBASTM-4P (page 55). A

E1 Terminations (pages 60, 63, 66)–New unit added OmniBASTM-4P. A

Cable Characteristics

New cable characteristics for new unit OmniBASTM-4P (pages 73 - 75). A

Appendix-C: Receptacles Pin Out

New receptacles pin-outs added for new unit OmniBASTM-4P (page 95) A

OmniBAS -2W/4W/8W

Installation and Cabling Manual - Edition 6.0

Document Revision History

(Page intentionally left blank)

OmniBAS -2W/4W/8W

Installation and Cabling Manual - Edition 6.0

Table of Contents

1Introduction ......................................................................................................................1

About this Document..........................................................................................................1

Overview of OmniBAS Product Family ..............................................................................2

Safety Precautions.............................................................................................................5

2Installation Tools..............................................................................................................6

3Installation Material..........................................................................................................7

OmniBAS-2W.....................................................................................................................7

OmniBAS-4W/8W ............................................................................................................10

OmniBAS-4P....................................................................................................................14

4Before Starting the Installation.....................................................................................16

4.1 Installation Prerequisites..................................................................................................16

4.2 Cabling Overview .............................................................................................................20

Modem Cabling................................................................................................................21

RJ-45 Cabling (Ethernet Payload) ...................................................................................23

RJ-45 Cabling (Outband Management) ...........................................................................24

SFP Cabling (Ethernet Payload) ......................................................................................25

SFP Cabling (STM-1 Payload).........................................................................................26

E1 Cabling (Balanced 120 Ω) ..........................................................................................27

Power Supply Cabling......................................................................................................28

Other Cabling...................................................................................................................29

5Mechanical Installation..................................................................................................32

5.1 OmniBAS-2W...................................................................................................................32

Chassis Overview ............................................................................................................32

IDU Installation.................................................................................................................33

5.2 OmniBAS-4W...................................................................................................................34

Chassis Overview ............................................................................................................34

IDU Installation.................................................................................................................35

5.3 OmniBAS-8W...................................................................................................................37

Chassis Overview ............................................................................................................37

IDU Installation.................................................................................................................38

5.4 OmniBAS-4P....................................................................................................................39

Chassis Overview ............................................................................................................39

IDU Installation.................................................................................................................40

6Cabling Installation........................................................................................................42

6.1 Power Supply Cables.......................................................................................................43

Preparation ......................................................................................................................44

Installation........................................................................................................................48

6.2 IF Tails .............................................................................................................................56

6.3 E1 Terminations...............................................................................................................59

Open End Cables (Balanced 120 Ω)................................................................................59

Table of Contents

BNC Terminations (Unbalanced 75 Ω) ............................................................................62

RJ-45 Terminations (Balanced 120 Ω).............................................................................65

6.4 I/O Cables ........................................................................................................................68

6.5 Ethernet Cables ...............................................................................................................70

7Cable Characteristics ....................................................................................................71

7.1 GbE Cable Characteristics...............................................................................................71

OmniBAS-2W...................................................................................................................71

OmniBAS-4W/8W ............................................................................................................72

OmniBAS-4P....................................................................................................................73

7.2 Fast Ethernet Cable Characteristics ................................................................................74

OmniBAS-2W...................................................................................................................74

OmniBAS-4W/8W ............................................................................................................74

OmniBAS-4P....................................................................................................................75

7.3 STM-1 Cable Characteristics ...........................................................................................76

OmniBAS-4W/8W ............................................................................................................76

Appendix-A: Modem Card Installation / Removal ..................................................................77

Appendix-B: I/O Connections ..................................................................................................80

Appendix-C: Receptacles Pin Out ...........................................................................................83

OmniBAS-2W...................................................................................................................83

OmniBAS-4W/8W ............................................................................................................89

OmniBAS-4P....................................................................................................................95

Appendix-D: Open End Cables Color Codes..........................................................................99

Equipment Disposal

Disposal of old electrical and electronic equipment (applicable through

the European Union and other European countries with separate waste

collection systems).

This symbol, found on this product and any of its parts or on its operating

instructions or on its packaging, indicates that electrical and electronic

equipment may not be disposed of as unsorted municipal waste. Instead,

this product should be handed over to applicable collection points for the

recycling of electrical and electronic equipment.

By ensuring the correct disposal of this product, you will help prevent

potential negative consequences to the environment and human health,

which could otherwise be caused by inappropriate disposal of this product.

By recycling, reusing and other forms of recovery of old electrical and

electronic equipment you are making an important contribution to the

conservation of natural resources and to the protection of the environment.

For more information about the recycling of this product, please contact your

local municipal authorities, municipal waste disposal service or the store

where you purchased this product.

Απόρριψη παλαιών ηλεκτρικών και ηλεκτρονικών συσκευών (ισχύει

στην Ευρωπαϊκή Ένωση και άλλες Ευρωπαϊκές χώρες με συστήματα

χωριστής συλλογής απορριμμάτων).

Το σύμβολο αυτό, που απεικονίζεται πάνω στο προϊόν και σε τυχόν

εξαρτήματα του ή στο εγχειρίδιο οδηγιών του ή στη συσκευασία του, δείχνει

ότι οι ηλεκτρικές και ηλεκτρονικές συσκευές, μετά το πέρας της λειτουργίας

τους, δεν θα πρέπει να απορρίπτονται μαζί με τα αστικά απόβλητα. Αντίθετα

θα πρέπει να παραδίδονται σε κατάλληλα σημεία συλλογής για την

ανακύκλωση των ηλεκτρικών και ηλεκτρονικών συσκευών.

Διασφαλίζοντας τη σωστή απόρριψη αυτού του προϊόντος, συνεισφέρετε

στην πρόληψη πιθανών αρνητικών συνεπειών στο περιβάλλον και την

ανθρώπινη υγεία, οι οποίες θα μπορούσαν να προκληθούν από την μη

ενδεδειγμένη απόρριψη του προϊόντος.

Η ανακύκλωση, επαναχρησιμοποίηση και άλλες μορφές αξιοποίησης των

παλαιών ηλεκτρικών και ηλεκτρονικών συσκευών βοηθούν στη διαφύλαξη

των φυσικών πόρων και στην προστασία του περιβάλλοντος.

Για περισσότερες πληροφορίες σχετικά την ανακύκλωση αυτού του

προϊόντος, παρακαλούμε επικοινωνήστε με τις τοπικές δημοτικές αρχές, την

υπηρεσία αποκομιδής αστικών αποβλήτων ή το κατάστημα από το οποίο

αγοράσατε το συγκεκριμένο προϊόν.

Για περισσότερες πληροφορίες, μπορείτε να επικοινωνείτε με το Συλλογικό

Σύστημα Εναλλακτικής Διαχείρισης Αποβλήτων Ηλεκτρικού και Ηλεκτρονικού

Εξοπλισμού “Ανακύκλωση Συσκευών Α.Ε.” (www.electrocycle.gr).

Declaration of Conformity

Hereby, Intracom S.A. Telecom Solutions declares that the

product OmniBAS is in compliance with the essential

requirements and other relevant provisions of the directive

1999/5/EC, and with the requirements of the RoHS directive

2011/65/EU.

For further information, please visit the following URL:

http://emc.intracom-telecom.com/

Δήλωση Συμμόρφωσης

Με την παρούσα, ηIntracom Α.Ε. Τηλεπικοινωνιακών Λύσεων

δηλώνει ότι το προϊόν OmniBAS συμμορφώνεται προς τις

ουσιώδεις απαιτήσεις και τις λοιπές διατάξεις της οδηγίας

1999/5/EC, καθώς και με τις απαιτήσεις της οδηγίας RoHS

2011/65/EU.

Για περισσότερες πληροφορίες γύρω από τη δήλωση

συμμόρφωσης, παρακαλούμε επισκεφθείτε την κάτωθι

ιστοσελίδα:

http://emc.intracom-telecom.com/

OmniBAS -2W/4W/8W

Installation and Cabling Manual - Edition 6.0

1 Introduction

About this Document

Scope of

document

This document provides information concerning the installation and cabling

of the following OmniBAS™ Indoor Units (IDUs) units:

•OmniBASTM-2W

•OmniBASTM-4W

•OmniBASTM-8W

•OmniBASTM-4P

Target

Audience

This document is addressed to certified technicians with wireless equipment

knowledge and skills concerning the following:

•Indoor Unit Installation (IDU).

•Addition / Removal of IDU Cards.

•Laying and Installation of Cables.

•Preparation & Termination of: Ethernet, E1, Power cables e.t.c

•Test & Measurement of cables (Ethernet, Optical, Power).

•Equipment Grounding to the Main Grounding System.

Reference

Manuals

The following document for OmniBASTM IDU Installation can be used for

additional product information and are available by Intracom S.A. Telecom

Solutions:

Item Description

1 OmniBAS_ODU_Installation Manual.

2 OSDR_Installation Manual.

Conventions This document applies the following conventions:

This symbol means DANGER. The purpose of this symbol is to

warn you that any wrong action can cause bodily injury or even

death.

This symbol means CAUTION. The purpose of this symbol is to

prevent you from performing an action that might result in damage

of the equipment.

A note calls your attention to important supplementary information.

Chapter 1. Introduction

Overview of OmniBAS Product Family

Introduction The OmniBAS™ family of Intracom Telecom IP MW PtP portfolio comprises:

•Split-mount systems:

−OmniBAS™ Indoor Units (IDUs) 1RU / 2RU high and 19″wide.

−OmniBAS™ Outdoor Units (ODUs) & antenna systems.

•All-outdoor system:

−OmniBAS™ OSDR (Outdoor Software-Defined Radio) integrating

everything (baseband / controller / modem / radio) into a robust

enclosure.

This document describes the installation of:

•OmniBAS™ - 2W/4W/8W IDUs for Split-mount system.

•OmniBAS™ - 4P IDU for All-outdoor system.

Continued on next page

Manuali Hardware di rete popolari di altre marche

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuale utente

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuale utente

Yudor

Yudor YDS-16 Manuale utente

D-Link

D-Link ShareCenter DNS-320L Manuale utente

Samsung

Samsung ES1642dc Istruzioni per l’uso

Honeywell Home

Honeywell Home LTEM-PV Istruzioni per il montaggio

evertz

evertz 7700 Series Manuale utente

D-Link

D-Link ShareCenter DNS-343 Manuale utente

Asante

Asante AsanteBridge 1012 Manuale utente

FireBrick

FireBrick FB2700 Manuale utente

Audiovox Electronics

Audiovox Electronics ARWH2T Manuale utente

ADC

ADC DSX-1 Manuale

NetComm

NetComm NF2 Manuale utente

Alcatel-Lucent

Alcatel-Lucent 5620 Manuale utente

Dell EMC

Dell EMC XC6420 Series Manuale utente

Lanner

Lanner NCA-1020A Manuale utente

Allied Telesis

Allied Telesis AT-TN121-A Manuale utente

Arista

Arista CCA-ETM-Q12 Manuale utente