Skil 2597 Manuale utente
CORDLESS IMPACT DRILL/DRIVER
2497 (F0152497 . . )
2597 (F0152597 . . )
SKIL Europe BV - Konijnenberg 60 10/07 2610398170
4825 BD Breda - The Netherlands
www.skileurope.com
www.skileurope.com
INSTRUCTIONS page 7
INSTRUCTIONS page 10
HINWEISE Seite 14
INSTRUCTIES bladz. 18
INSTRUKTIONER sida 22
INSTRUKTION side 26
ANVISNING side 29
OHJEET sivu 33
INSTRUCCIONES pág. 36
INSTRUÇÕES pág. 40
ISTRUZIONI pag. 44
LEÍRÁS oldal 48
POKYNY strana 52
KILAVUZ sayfa 55
INSTRUKCJA strona 59
ИНСТРУКЦИИ страница 63
ІНСТРУКЦІЯ страница 68
O∆ΗΓΙΕΣ σελίδα 72
INSTRUCØIUNI pagina 77
УKA3AНИЕ страница 80
POKYNY strana 85
UPUTE stranica 89
UPUTSTVA stranica 93
NAVODILA stran 96
KASUTUSJUHEND lehekülg 100
INSTRUKCIJA lappuse 103
INSTRUKCIJA puslapis 107
GB
F
D
NL
S
DK
N
FIN
E
P
I
H
CZ
TR
PL
RU
UA
GR
RO
BG
SK
HR
SRB
SLO
EST
LV
LT
ME77
2
14,4 V
2,1 kg
0-350/1300
1
12
AB
D
C
E
G
F
2 3
25mm
6 mm
1 hour
max. 22Nm
18 V
2,3 kg
0-350/1300
15 28mm
6 mm
30 min.
max. 25 Nm
2497
2597
9
3
GH
2497
2597
NiCd
47856
4
0
! @
#
15
1
$
5
% ^
&
*PHILLIPS
POZIDRIV
SLOTTED
6
()
¡ ™
Battery 14,4 V (2497) 1,2 Ah NiCd 2610393024
Battery 18 V (2597) 2,0 Ah NiCd 2610395721
ACCESSORIES SKIL nr.
7
GB
Cordless impact drill/driver 2497/2597
INTRODUCTION
• This tool is intended for impact drilling in brick as well
as for drilling in wood, metal, ceramic and plastic; tools
with electronic speed control and left/right rotation are
also suitable for screwdriving and thread cutting
• Read and save this instruction manual 3
TECHNICAL SPECIFICATIONS 1
TOOL ELEMENTS 2
ASwitch for on/off and speed control
BSwitch for changing direction of rotation
CKeyless chuck
DRing for torque control
ESwitch for selecting mechanical speed
FAuxiliary handle
GGreen charging light (2597)
HRed charging light (2597)
SAFETY
GENERAL SAFETY INSTRUCTIONS
WARNING! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or serious
injury. Save all warnings and instructions for future
reference. The term “power tool” in the warnings refers to
your mains-operated (corded) power tool or battery-
operated (cordless) power tool.
1) WORK AREA SAFETY
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk
of electric shock.
b) Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
3) PERSONAL SAFETY
a) Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or medication.
A moment of inattention while operating power tools
may result in serious personal injury.
b) Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce
personal injuries.
c) Prevent unintentional starting. Ensure the switch is
in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger on the
switch or energising power tools that have the switch
on invites accidents.
d) Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal
injury.
e) Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power
tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long
hair can be caught in moving parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
b) Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
8
e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc.,
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
5) BATTERY TOOL USE AND CARE
a) Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fire when used with
another battery pack.
b) Use power tools only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
c) When battery pack is not in use, keep it away from
other metal objects like paper clips, coins, keys,
nails, screws, or other small metal objects that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause
burns or a fire.
d) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation or burns.
6) SERVICE
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
SAFETY INSTRUCTIONS FOR CORDLESS DRILL/
DRIVERS
• Wear ear protectors with impact drills (exposure to
noise can cause hearing loss)
• Use auxiliary handles supplied with the tool (loss of
control can cause personal injury)
• Do not work materials containing asbestos
(asbestos is considered carcinogenic)
• Dust from material such as paint containing lead, some
wood species, minerals and metal may be harmful
(contact with or inhalation of the dust may cause
allergic reactions and/or respiratory diseases to the
operator or bystanders); wear a dust mask and work
with a dust extraction device when connectable
• Certain kinds of dust are classified as carcinogenic
(such as oak and beech dust) especially in conjunction
with additives for wood conditioning; wear a dust
mask and work with a dust extraction device when
connectable
• Follow the dust-related national requirements for the
materials you want to work with
• Hold the power tool only by the insulated gripping
surfaces when performing an operation where the
accessory may contact hidden wiring or its own
power cord (contact with a “live” wire will also make
exposed metal parts of the power tool “live” and shock
the operator)
• Use suitable detectors to find hidden utility lines or
call the local utility company for assistance (contact
with electric lines can lead to fire or electrical shock;
damaging a gas line can result in an explosion;
penetrating a water pipe will cause property damage or
an electrical shock)
• Secure the workpiece (a workpiece clamped with
clamping devices or in a vice is held more securely than
by hand)
• Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working
• Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the charger
(chargers with a rating of 230V or 240V can also be
connected to a 220V supply)
• In case of electrical or mechanical malfunction,
immediately switch off the tool or unplug charger from
power source
• SKIL can assure flawless functioning of the tool only
when original accessories are used
• Use only accessories with an allowable speed matching
at least the highest no-load speed of the tool
• This tool should not be used by people under the age of
16 years
• Ensure that switch B 2is in the middle (locking)
position before making any adjustments or changing
accessories as well as when carrying or storing the tool
CHARGING/BATTERIES
• Charge battery only with the charger that is supplied
with the tool
• Do not touch the contacts in the charger
• Do not expose tool/charger/battery to rain
• Store tool/charger/battery in locations where
temperature will not exceed 40°C or drop below 0°C
• Batteries will explode in fire, so do not burn battery for
any reason
• Do not use charger when damaged; take it to one of the
officially registered SKIL Service Stations for a safety
check
• Do not use charger when cord or plug is damaged; cord
or plug should be replaced immediately at one of the
officially registered SKIL Service Stations
• Do not use battery when damaged; it should be
replaced immediately
• Do not disassemble charger or battery
• Do not attempt to recharge non-rechargeable batteries
with the charger
9
• Explanation of symbols on charger/battery
3Read the instruction manual before use
4Only use the charger indoors
5Double insulation (no earth wire required)
6Fail-safe isolating transformer (the power source is
electrically separated from the transformer output)
7Do not dispose of the charger together with
household waste material
8Do not dispose of the battery together with
household waste material
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live) wire
in the cord of the charger to the earth terminal of the
plug
• If for any reason the old plug is cut off the cord of the
charger, it must be disposed of safely and not left
unattended
USE
• Charging battery 9
- battery of new tools is not fully charged
- after approximately 1 hour the battery is fully charged
(2497)
- after approximately 1/2 hour the battery is fully
charged and green light G stays on after blinking, at
which time the charger automatically switches to
maintenance-charging (2597)
! remove battery from charger after charging
period has ended thereby lengthening the service
life of the battery
IMPORTANT:
- if red light H turns on, this indicates that the battery
is too cold or too hot (charger only charges batteries
when its temperature is between 0°C and 45°C); the
charger then automatically switches to maintenance-
charging, until a temperature between 0°C and 45°C
is reached, at which time the charger will
automatically switch to normal charging (2597)
- if red light H starts blinking, this indicates that the
battery should be cleaned or replaced (2597)
- while charging, the charger and the battery may
become warm to touch; this is normal and does not
indicate a problem
- ensure that the outside surface of the battery is clean
and dry before inserting into charger
- do not charge at temperatures below 0°C and over
40°C; this will seriously damage the battery as well
as the charger
- do not remove battery from tool while it is running
! a battery that is new or has not been used for a
longer period does not develop its full capacity
until after approximately 5 charging/discharging
cycles
- do not repeatedly recharge the battery after only a
few minutes of operation; this may result in a
reduction of operating time and battery efficiency
- the nickel-cadmium battery must be kept separate
from the natural environment and should not be
disposed of as normal domestic waste (symbol 8
will remind you of this when the need for disposing
occurs)
! prior to disposal protect battery terminals with
heavy tape to prevent short-circuit
- if you anticipate long periods of non-use for the tool,
it is best to unplug the charger from its power source
• On/off 0
• Speed control for smooth starting !
• Changing direction of rotation @
- when not properly set in left/right position, switch
A 2cannot be activated
! change direction of rotation only when tool is at a
complete standstill
• Changing bits #
- insert the bit as deep as possible in the chuck
! do not use bits with a damaged shank
• Torque control (VariTorque) $
- limits the amount of output torque delivered by the
chuck (17 clutch settings)
- when turning in a screw, first try VariTorque position 1
and increase until the desired depth has been
reached
• 2 Mechanical speeds %
- set switch E to desired speed
! change speed while tool is running slowly
1 = HIGH POWER
- high torque
- for screwdriving and drilling large diameters
- for tapping thread
2 = HIGH SPEED
- lower torque
- for drilling small diameters
- for impact drilling
• Adjusting drilling depth ^
• Holding and guiding the tool &
- always use auxiliary handle F 2(can be adjusted
as illustrated)
- keep the ventilation slots uncovered
- do not apply too much pressure on the tool; let the
tool do the work for you
APPLICATION ADVICE
• Use the appropriate bits *
! only use sharp bits
• When drilling ferrous metals
- pre-drill a smaller hole, when a large hole is required
- lubricate drill bit occasionally with oil
• When turning in a screw at/near the cross cut end or an
edge of wood, pre-drill a hole in order to avoid cracking
of the wood
• For an optimal use of the tool a steady pressure on the
screw is required, especially while removing
• When screwdriving in hard wood one should pre-drill a
hole
• Splinterfree drilling in wood (
10
• Dustfree drilling in walls )
• Dustfree drilling in ceilings ¡
• Drilling in tiles without skidding ™
• For more tips see www.skileurope.com
• Vibration level
The vibration emission level stated at the back of this
instruction manual (indicated by an asterisk) has been
measured in accordance with a standardised test given
in EN 60745; it may be used to compare one tool with
another and as a preliminary assessment of exposure to
vibration when using the tool for the applications
mentioned
- using the tool for different applications, or with
different or poorly maintainted accessories, may
significantly increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may
significantly reduce the exposure level
! protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work
patterns
MAINTENANCE / SERVICE
• Keep tool and charger clean
- the charger may be cleaned most effectively with
compressed air (wear safety goggles)
- clean charging contacts in charger with alcohol or
contact cleaner
! unplug charger from power source before cleaning
• If the tool/charger should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool or charger undismantled together with
proof of purchase to your dealer or the nearest SKIL
service station (addresses as well as the service
diagram of the tool are listed on www.skileurope.com)
ENVIRONMENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2002/96/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 7will remind you of this when the need for
disposing occurs
F
Perceuse à percussion/ 2497/2597
visseuse sans fil
INTRODUCTION
• Cet outil est conçu pour les travaux de perçage à
percussion dans la brique ainsi que le perçage dans le
bois, le métal, la céramique et les matières plastiques;
les outils avec réglage électronique de la vitesse et
rotation à droite/à gauche sont également appropiés
pour le vissage et le filetage
• Lisez et conservez ce manuel d’instructions 3
SPECIFICATIONS TECHNIQUES 1
ELEMENTS DE L’OUTIL 2
AInterrupteur de marche/arrêt et réglage de vitesse
BCommutateur pour inverser le sens de rotation
CMandrin auto-serrant
DAnneau pour réglage du couple
ECommutateur pour sélectionner la vitesse mécanique
FPoignée auxiliaire
GVoyant du chargeur vert (2597)
HVoyant du chargeur rouge (2597)
SECURITE
INSTRUCTIONS GENERALES DE SECURITE
ATTENTION! Lisez tous les avertissements de
sécurité et toutes les instructions. Ne pas suivre les
avertissements et instructions peut entraîner un choc
électrique, un incendie et/ou de graves blessures sur les
personnes. Conservez tous les avertissements et
toutes les instructions pour pouvoir s’y reporter
ultérieurement. La notion d’”outil électroportatif” dans les
avertissements se rapporte à des outils électriques
raccordés au secteur (avec câble de raccordement) et à
des outils électriques à batterie (sans câble de
raccordement).
1) SECURITE DE LA ZONE DE TRAVAIL
a) Maintenez l’endroit de travail propre et bien éclairé.
Un lieu de travail en désordre ou mal éclairé augmente
le risque d’accidents.
b) N’utilisez pas l’appareil dans un environnement
présentant des risques d’explosion et où se trouvent
des liquides, des gaz ou poussières inflammables.
Les outils électroportatifs génèrent des étincelles
risquant d’enflammer les poussières ou les vapeurs.
c) Tenez les enfants et autres personnes éloignés
durant l’utilisation de l’outil électroportatif.
En cas d’inattention vous risquez de perdre le
contrôle sur l’appareil.
Altri manuali per 2597
1
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali Skil Trapano avvitatore a batteria
Skil
Skil 2302 Manuale utente
Skil
Skil 2511 Manuale utente
Skil
Skil 2302 Manuale utente
Skil
Skil 2412 Manuale utente
Skil
Skil Masters 2502 Manuale utente
Skil
Skil Masters 2322 Manuale utente
Skil
Skil 2860 Istruzioni per il montaggio
Skil
Skil Masters 2702 Manuale utente
Skil
Skil 2016 Manuale utente
Skil
Skil 2490 Manuale utente
