Slinex DESIGN DIRECT ML-16 Manuale utente
{ Design. Unique. Innovation }
ML-16 video door panel
DESIGN
DIRECT
SERIES
Thank you for the
choice of our equipment
User manual
{ Design. Unique. Innovation }
12
Rev. 1.0
DESIGN
DIRECT
SERIES
Safety instructions
Read and keep that manual.
The device installation process should be carried out by the qulied specialists.
Use the device from the –40 ˚C to +65 ˚C, always keep it within that
temperature range.
Installation surface should be free from vibration and impact inuence.
Keep this device far from open sources of heat, such as radiators, heaters, and
ovens.
The device can be installed near other electronic equipment in case if the
temperature of the environment does not exceed previously mentioned
range.
The device should be protected from the direct inuence of the natural
phenomena, such as direct sunlight, rain or snow.
Don’t use aggressive or abradant detergent for the device surface cleaning.
Use soft wet cloth or tissue to remove strong dirt.
Attention!
As a result of continuous upgrades and functionality
improvements, technical characteristics of the device can
be changed without any preliminary declaration.
This manual can contain some inaccuracy or misprint.
The owner reserves the right to make corrections to the information described
in the user manual and device package.
The last revision of this manual is available on www.slinex.com
Nature protection
Don’t throw away the device with other industrial or
nutritive trash if you see that symbol. Some regions have
separation and recycling systems for the electronic
equipment.
Connect with local authorities to receive information about recycling of
electronic equipment for your region.
Rights and limitation of liability
All rights reserved. Any part of that document can not be published in any
form, translated into other languages or reproduced in any way including
electronic or mechanical.
Document recording and copying is strictly denied without owner permission.
!
{ Design. Unique. Innovation }
34
Table of contents
1. Package .................................................................................................................................. 4
2. Specication ......................................................................................................................... 4
3. Description............................................................................................................................ 6
4. Schematic diagram ............................................................................................................ 7
5. Installation............................................................................................................................. 8
6. Limited Warranty................................................................................................................. 9
1. Package
ML-16 door panel − 1 pc.
Angle bracket − 1 pc.
Rainshield − 1 pc.
Mounting screws and nuts − 1 pkg.
User manual − 1 pc.
2. Specication
DESIGN
DIRECT
SERIES
Sensor type
Resolution
View angle
Night backlight
Voltage
Power consumption
Installation type
Dimensions
Working temperature
1/3” CMOS
420 ТV-lines
56˚ (horizontal), 48˚ (vertical)
Infrared LED’s. 1,5 m distance
+12 V
2,4 W in working mode
Surface mount
41×122×23 mm
–40 ... +65 ˚C
5
4
3
2
1
{ Design. Unique. Innovation }
56
DESIGN
DIRECT
SERIES
1
2
3
4
5
Microphone
Video camera
Night infrared backlight
Call button
Speaker
3. Description
Red
Black
Yellow
White
Brown
Blue
ML-16 wire colors
Power, +12 V
Ground (GND)
Video
Audio
COM relay contact
N.O. relay contact
122 мм
41 мм
5
{ Design. Unique. Innovation }
78
DESIGN
DIRECT
SERIES
4. Schematic diagram 5. Installation
Power (Red)
Audio (White)
GND (Black)
Video (Yellow)
COM (Brown)
N.O. (Blue)
Lock
ML-16
SL-07M (Master)
Lock power
supply
Door 1
Door 2
CCTV 1
CCTV 2
Input
Output
PowerTV out
1) Take the angle bracket from the kit and situate it 150-160 cm from the oor
line;
2) Mark and drill two halls inside the wall;
3) Take two nuts from the kit and hammer them into the drilled halls;
4) Fix angle bracket on the wall by two screws from the kit;
5) Connect all communication wires and x the door panel on the angle
bracket by two screws from the faceplate side. Then install the caps on the
mounting screws.
{ Design. Unique. Innovation }
910
DESIGN
DIRECT
SERIES
6. Limited warranty
Manufacturer guarantees product normal functioning during the warranty
period if the user keeps all safety instructions described in that manual.
Warranty period is 12 months from the moment of the product purchasing.
Warranty period allows user to make guarantee repair in cases when normal
functioning of the product was violated by the fault of manufacturer and the
user haven’t oend transporting, installation and working conditions.
This limited warranty does not cover any damage to the product that results
from improper installation, accident, abuse, misuse, natural disaster,
insucient or excessive electrical supply, abnormal mechanical or
environmental conditions, or any unauthorized disassembly, repair or
modication.
Warranty void in such cases:
• the product was damaged by the fault of the customer;
• the product wasn’t properly installed according reccomendations from
the manual;
• the sticker on the backside of the product was broken;
• the product was not used for its intended function.
This limited warranty covers only repair, replacement, refund or credit for
defective products, as provided above. Manufacturer is not liable for, and does
not cover under warranty, any damages or losses of any kind whatsoever
resulting from loss of, damage to, or corruption of, content or data or any costs
associated with determining the source of system problems or removing,
servicing or installing products. This warranty excludes third party software,
connected equipment or stored data. Manufacturer is therefore not liable for
any losses or damage attributable to third party software, connected
equipment or stored data.
In the event a product has been discontinued, manufacturer shall either repair
the product, oer to replace it with a comparable product or provide a refund
at the lesser of the purchase price or the product’s current value.
Repaired or replacement products will continue to be covered by this limited
warranty for the remainder of the original warranty term.
Altri manuali Slinex Sistema di interfono
Slinex
Slinex RD-30 Manuale utente
Slinex
Slinex ML-20CRHD Manuale utente
Slinex
Slinex ML-17HD Manuale utente
Slinex
Slinex SONIK 7 Cloud Manuale utente
Slinex
Slinex UNIQUE DIRECT IP Series Manuale
Slinex
Slinex SL-07M Manuale utente
Slinex
Slinex UNIQUE DIRECT Series Manuale utente
Slinex
Slinex SM-07MN Manuale utente
Slinex
Slinex VR-16 Manuale utente
Slinex
Slinex Tabo Manuale utente
Slinex
Slinex SQ-07MT HD Manuale utente
Slinex
Slinex SM-07 Manuale utente
Slinex
Slinex IP DIRECT Series Manuale utente
Slinex
Slinex ML-20HR Manuale utente
Slinex
Slinex ML-20CR Manuale utente
Slinex
Slinex Innovation Direct Series Manuale utente
Slinex
Slinex SQ-07MTHD Manuale utente
Slinex
Slinex Innovation Direct Series Manuale utente
Slinex
Slinex SM-07N Cloud Manuale utente
Slinex
Slinex ML-15HD Manuale utente
