Smacq Technologies PCI-3000 Series Manuale utente

PCI-3000 Series Multifunctional Data

Acquisition Devices

User Manual

Rev. A

Beijing Smacq Technology Co., Ltd.

Smacq.com

Smacq.cn

1 |

Statement

No content of this manual may be reproduced, modified or abridged without prior consent and

written permission.

Trademark information

Smacq is a registered trademark of Beijing Smacq Technology Co., Ltd.

The names of the other products and companies mentioned in this document are trademarks ortrade

names of their respective companies.

Other Disclaimer

The information provided in this document may be modified and updated in subsequent

versions without prior notice.

Smacq does not provide any warranties, express or implied, for this document as well as the

information inside it, including but not limited to implied warranties of the marketable nature of

the product and its suitability for a particular purpose.

There may be a chance that inaccurate descriptions or errors exist in this document. Smacq does

not hold any liability for accidents because of the information and deductive functions provided

in this manual, as well as the resulting loss of any chance because of the use of this document.

Smacq reserves the rights to change product specifications, prices, and decide whether to stop

the production.

If you have any questions or need assistance in using this product or this document, please contact us

via:

Phone: (+86)10 - 52482802

E-Mail: service@smacq.com

Website: http://www.smacq.com

http://www.smacq.cn

2 |

Safety Requirements

Warning

Only the voltage within the specified range can be connected. Voltage

exceeding the specified range may cause damage to

the device, and

even present a negative impact on personal safety. Check the product

specification for detailed reference to the range of voltages that can be

connected by each port.

Warning

Do not attempt to operate the device in other ways that are not

mentioned in this document. Incorrect use of the device may be

dangerous. In the event of device damage, the internal security

protection mechanism will also be affected.

Warning

Do not attempt to replace device components or change devices in other

ways that are not mentioned in this document. Do not repair the device

yourself in the event of a product failure.

Warning

Do not use the device in an environment where an explosion may occur

or where flammable flue or gas is present. If you must use the

device in

this kind of environment, please fit it into a proper case.

Warning

While the device is running, all chassis covers and fill panels need to be

closed.

Warning

For equipment with exhaust vents, do not insert foreign objects into the

vents or

block air circulation in the vents.

3 |

Warning

For use in measurement category I (CAT I) only. Do not use in

measurement category II/III/IV. Use this device to connect signals

or make measurements.

Measurement Categories

Measurement categories Note

Measurement categories I (CAT I) means that measurements are made on a circuit that is not directly

connected to the main power supply. For example, a circuit that is not exported from the main power

supply, especially a circuit that is exported from a protected (internal) primary power supply, is

measured. In the latter case, the instantaneous stress will change. Therefore, the user should be aware

of the instantaneous affordability of the device.

Measurement categories II (CAT II) means that measurements are made on a circuit that is directly

connected to a low-voltage device. For example, a measurement on household appliances, portable

tools and similar equipment.

Measurement categories III (CAT III) means that measurements are made in construction equipment.

For example, a measurement on the distribution boards, circuit breakers, wiring (including cables,

Busbars, junction boxes, switches, sockets) in fixed equipment and equipment for industrial use and

certain other equipment (for example, fixed motors that are permanently connected to fixtures).

Measurement categories IV (CAT IV) means that measurements are made on the source of low-

voltage equipment. For example, a measurement on a meter, a major overcurrent protection device,

and a pulse control unit.

4 |

Warning Some of the substances contained in this product may be harmful

to the environment or human health. In order to avoid releasing

harmful substances into the environment or endangering human

health, it is recommended that appropriate methods be used to

recover this product to ensure that most materials can be

properly reused or recycled. For information about processing or

recycling, please contact your local professional organizations.

Environment

Temperature

Operating 0℃ ~ 55℃

Storage -40℃ ~ 85℃

Humidity

Operating 5%RH ~ 95%RH, no condensation

Storage 5%RH ~ 95%RH, no condensation

Pollution degree 2

Highest elevation 2000 m

Pollution degree description

Pollution degree 1: No pollution, or only dry non-conductive pollution. This pollution degree has no

effect. For example: a clean room or an air-conditioned office environment.

Pollution degree 2: Generally only dry non-conductive pollution occurs. Temporary conduction can

sometimes occur due to condensation. For example: General indoor environment.

Pollution degree 3: Conductive pollution occurs, or dry non-conductive pollution becomes

conductive due to condensation. For example, an outdoor sheltered environment.

Pollution degree 4: Permanent conductive pollution caused by conductive dust, rain, or snow. For

example: Outdoor places.

Recycle precautions

5 |

CONTENT

Statement .......................................................................................................1

Safety Requirements.......................................................................................2

Measurement Categories ...............................................................................3

Environment ...................................................................................................4

1. Getting Started..........................................................................................7

1.1. Product introduction...........................................................................7

1.2. Function Diagram..............................................................................10

1.3. Product specifications.......................................................................10

1.4. Product unpacking ............................................................................15

Precautions .............................................................................................15

Check the packing list..............................................................................15

2. Installation ..............................................................................................16

2.1. Connector signal pins distribution ....................................................16

2.2. Drive installation ...............................................................................19

3. Analog Input（AI）................................................................................24

3.1. Signal connection methods...............................................................24

3.2. Floating grounded signal source .......................................................25

Using differential mode (DIFF) connection .............................................25

Non-grounded reference single-ended mode (NRSE) connection..........27

3.3. Grounded Signal Source....................................................................28

Use a differential mode (DIFF) connection .............................................28

Use a non-grounded reference single-ended mode (NRSE) connection.29

3.4. Signal acquisition mode ....................................................................30

Continuous acquisition mode .................................................................30

Limited number acquisition mode ..........................................................31

Single point reading ................................................................................31

3.5. Comprehensive sampling rate and single channel sampling rate.....31

3.6. Trigger...............................................................................................31

Clear trigger ............................................................................................32

4. Analog Output (AO) ................................................................................33

4.1. Signal output mode...........................................................................33

DC immediate output .............................................................................33

6 |

Finite number output mode ...................................................................33

Infinite loop output mode.......................................................................34

Infinite non-loop output mode ...............................................................34

4.2. Output update rate ...........................................................................34

4.3. Trigger...............................................................................................34

Clear trigger ............................................................................................35

5. Digital Input（DI）.................................................................................36

5.1. Signal acquisition mode ....................................................................36

Continuous acquisition mode .................................................................36

Limited number acquisition mode ..........................................................36

Single read ..............................................................................................36

5.2. Trigger...............................................................................................37

Clear Trigger............................................................................................37

6. Digital Output（DO）.............................................................................38

6.1. Signal output mode...........................................................................38

Immediate output...................................................................................38

Finite number output mode ...................................................................38

Infinite loop output mode.......................................................................38

Infinite non-loop output mode ...............................................................39

6.2. Output update rate ...........................................................................39

6.3. Trigger...............................................................................................39

Clear trigger ............................................................................................39

7. Synchronization System ..........................................................................40

7.1. Synchronous clock ............................................................................40

7.2. External trigger input ........................................................................40

7.3. Trigger output ...................................................................................40

8. Service and Warranty..............................................................................42

9. Ordering Information..............................................................................43

7 |

1. Getting Started

This chapter describes the basic functions of PCI-3000 Series Data Acquisition Device, as well as

product specifications and precautions in the process of product unpacking.

1.1. Product introduction

PCI-3000 series data acquisition device is a multi-functional data acquisition device based on PCI

bus, which can be used for continuous high-speed signal acquisition and control signal output when

installed ina computer.

PCI-3000 series of data acquisition devices can measure analog and digital signals continuously and

save the data to the computer hard drive without interruption. Itcan also provide digital signal output,

periodic repetitive signal output

PCI-3000 series data acquisition device supports operating in Windows OS, providing standard

DLLs and support for mainstream development languages including VC++, VB, C#, LabVIEW,and

MATLAB.

Key Features

16-bit analog input resolution, support continuous uninterrupted acquisition

Up to 1MS/s sampling rate for analog input

The input can be set to various ranges of ±10V/5V/2.5V/1.25V/0.6V by software.

Analog input channels support single-ended or differential wiring.

16-bit analog output resolution, with output range of ±10V

Up to 1MS/s sampling rate for analog input

Up to 10MS/s/Ch sampling rate for digital I/O

8 |

PCI-3000 series data acquisition device contains several models, and the main differences of each

model are as follows:

PCI-3210

PCI-3211

PCI-3212

PCI-3213

Analog input

channel quantity

8 Single-Ended

/ 4 Difference

8 Single-Ended /

4 Difference

8 Single-Ended

4 Difference

8 Single-Ended

/ 4 Difference

Analog input

resolution

16-bit 16-bit 16-bit 16-bit

Analog input

Sampling rate

125kS/s 250kS/s 500kS/s 1MS/s

Analog output

channel quantity

0 0 0 0

PCI-3220

PCI-3221

PCI-3222

PCI-3223

Analog input

channel quantity

16 Single-Ended

/ 8 Difference

16 Single-Ended

/ 8 Difference

16 Single-Ended

/ 8 Difference

16 Single-Ended

/ 8 Difference

Analog input

resolution

16-bit 16-bit 16-bit 16-bit

Analog input

Sampling rate

125kS/s 250kS/s 500kS/s 1MS/s

Analog output

channel quantity

0 0 0 0

PCI-3110

PCI-3111

PCI-3112

PCI-3113

Analog input

channel quantity

8 Single-Ended

/ 4 Difference

8 Single-Ended /

4 Difference

8 Single-Ended

4 Difference

8 Single-Ended

/ 4 Difference

Analog input

resolution

16-bit 16-bit 16-bit 16-bit

Analog input

Sampling rate

125kS/s 250kS/s 500kS/s 1MS/s

Analog output

channel quantity

2 2 2 2

Analog output

resolution

16-bit 16-bit 16-bit 16-bit

Analog output

Sampling rate

1MS/s 1MS/s 1MS/s 1MS/s

9 |

PCI-3120

PCI-3121

PCI-3122

PCI-3123

Analog input

channel quantity

16 Single-Ended

/ 8 Difference

16 Single-Ended

/ 8 Difference

16 Single-Ended

/ 8 Difference

16 Single-Ended

/ 8 Difference

Analog input

resolution

16-bit 16-bit 16-bit 16-bit

Analog input

Sampling rate

125kS/s 250kS/s 500kS/s 1MS/s

Analog output

channel quantity

2 2 2 2

Analog output

resolution

16-bit 16-bit 16-bit 16-bit

Analog output

Sampling rate

1MS/s 1MS/s 1MS/s 1MS/s

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Smacq Technologies Hardware per computer

Smacq Technologies

Smacq Technologies USB-5100 Series Manuale utente

Smacq Technologies

Smacq Technologies PCI-1232 Manuale utente

Smacq Technologies

Smacq Technologies USB-3300 Series Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente