Smart Cabling & Transmission IP03PT Manuale utente
1
IP/PoE CABLING TRANSMISSION
ITEM NO.: IP03P PoE Extender over Coax/Two Wire
IP03P PoE Extender is designed to send and extend Ethernet network with PoE can be
established using existing cables up to 600M. You can use Coax cable either any two-wire
cables (UTP cable, telephone line, antenna cable, or bell wire) that is no longer in use to
connect a 10/100Mbps PoE device, IP telephone, PC…etc without having to lay any new cables.
Extended pass through PoE to allow a single PoE source, such as a PoE network switch (IEEE
802.3af/at) to provide power to both TX/RX and the IP/PoE camera use. It is perfect solution
for extended distance data and power transmission for warehouses, parking lots, campuses,
casinos and many more.
IP03P PoE Extender over Coax/Two Wire
Extend POE signal up to 600M, Ethernet or any TCP/IP devices up to 1000M.
Ethernet and PoE data over coax or any two wire cables (UTP, telephone, bell, alarm,
power cables.
Support 10/100 Mbps transmission rate.
Power source either from PoE Switch or external DC power adapter option. (order
separately)
Provides pass-through PoE up to IEEE802.3at 30W.
Provides DC12V 1Amp power to camera.
Support high power PoE to PTZ cameras at long distances.
IP03P Power Source Option Model:
DC48V 40W power adapter: SWP480830
DC56V 70W power adapter: SWP551260
High Power PoE Injector/ PoE Switch: IP06I, IP06H
Installation View:
1. Connect IP03PT, IP03PR with any two wire cable at both ends before powering.
2. Power input source could use PoE Injector/Switch either optional DC 48V, DC56 power
adapter to IP03PR unit and camera use.
IP03PT
IP03PR
2
Different Two Wire Cables Distance Chart for Reference:
Please note the cable quality, length and diameter of two wires used all have
an influence on the transfer of data and the PoE output.
CABLE
Distance
Power Input
Data Rate
PoE Output
DC 12V
Output
Coax
Cable
RG59
500
PoE 54V
71.2Mbps
11.8~12.4W
1000mA
DC 55.5V
71.2Mbps
12.8~13.5W
1000mA
DC 48V
71.2Mbps
8.7~9.2W
1000mA
1000
DC 55.5V
56Mbps
N/A
N/A
DC 48V
47.5Mbps
N/A
N/A
1500
PoE 54V
40Mbps
N/A
N/A
DC 55.5V
48Mbps
N/A
N/A
CABLE
Distance
Power Input
Data Rate
PoE Output
DC 12V
Output
Coax
Cable
RG6U
600
PoE 54V
70.5Mbps
11.8~12.4W
1000mA
DC 55.5V
73Mbps
8.7~9.2W
1000mA
DC 48V
72Mbps
8.2~8.7W
1000mA
CABLE
Distance
Power Input
Data Rate
PoE Output
DC 12V
Output
CAT.5e
Cable
4 Pairs
600
PoE 54V
59Mbps
13W
900mA
DC 55.5V
68Mbps
16.5~17.5W
1000mA
DC 48V
60Mbps
13W
900mA
1000
PoE 54V
41Mbps
N/A
N/A
DC 55.5V
44Mbps
N/A
N/A
DC 48V
42.5Mbps
N/A
N/A
IP03PR
IP03PT
IP03PT
IP03PR
3
CABLE
Distance
Power Input
Data Rate
PoE Output
DC 12V
Output
Telephone
Cable
0.65mm
200
PoE 54V
68Mbps
12W
900mA
DC 55.5V
80Mbps
18.5~19.5W
1000mA
DC 48V
73Mbps
12W
900mA
400
PoE 54V
68Mbps
8W
700mA
DC 55.5V
80Mbps
11W
850mA
DC 48V
73Mbps
4.8~5.4W
500mA
※Recommend external power adapter must use DC 48～57V 30W.
Panel View:
IP03PT
IP03PR
LED Indication：
LED Indication
Status
Function
ON
Red On
Power on
LINK
Blue On
Linked
STATUS
Red On
Link failed
RJ45
(Green/Orange)
Green Flash
Data transmission
Orange On
POE transmission
4
SETTING Button Function：
Use SETTING button to setup a group:
When IP03P need to create a group, please follow the following steps:
1. Connect IP03PR and IP03PT first then press the SETTING button 5~8 seconds of IP03PR
,the blue LED will be off, green LED will be on.
2. IP03PR Press the SETTING button 1~3 seconds then release, the RJ45 Green LED will be
flashing.
3. Within one minute to press 1~3 seconds and release unit of IP03PT SETTTING button, you
will see the IP03PT and IP03PR RJ45 Green LED under linking.
4. After complete the above steps, the blue/green LED become ON status that mean the group
has successfully established.
Reset to factory Default:
To press the SETTING button 10 seconds, then release, the RJ45 green LED will be off and on
again, orange LED will be off.
Slide Switch Function：
BNC Use coax cable to send data and power
TERMINAL Use two wire cables to send data and power
* Make sure the IP03TX/IP03RX both setting at same position of BNC/TERMINAL.
Terminal Function：
IP03PR
Orange: Output DC48-DC58V & data transmission
Black: Input DC48-DC58V
Group 1
Group 2
Group 3
Both wiring must be
away at least 30cm
Both wiring must be
away at least 30cm
5
IP03PT
Green: Output DC12V 1AMP (output power will be affected by the power cable thickness)
Orange: Receive IP03PR two wire power and data transmission.
6
Recommend cable：
RG59/6U COAX cable, CAT5e/6/7 UTP cable, telephone cable, power cable.
Please note the cable quality, length and diameter of two wires used all have an influence on
the transfer of data and the PoE output.
Cable Define：
Data/Power +
Data/Power –
Caution:
1. Power output will be varied based on the power source input.
IP03PR power input with two selections, but one time only could use one input
★Once choose power adapter power input, it cannot accept PoE devices input.
IP03PT power output with two selections, but one time only could use one method.
★Once choose DC 12V 1A power output, it cannot use PoE output power supply.
2. The linking Coax cable or two wire cable all carried with power, using two wire
installations, please pay attention the wiring polarity to avoid any damage.
3. IP03PT DC12V 1Amp output: the power output will be affected by the power cable
thickness.
4. The power consumption of the product itself on IP03PT/IP03PR is 5.5W.
5. If use PoE injector/switch as power input source, recommend to use high power PoE
IEEE802.3at in order to provide enough power to PoE devices or DC12V output.
6. The wiring must away from any equipment with electromagnetic wave in order to avoid
transmission distance become shorter, i.e.: mobile phone, microwave, radio equipment,
fluorescent lamp, power lines.
Package:
IP03PT x 1
IP03PR x 1
Screw Pack x 2
Rubber Pad x 2
Specifications:
ITEM NO.
IP03PT
IP03PR
RJ45 Interface
Data Transmission/ POE Output
Data Transmission/POE Input
Power, Data
Input /Output
Slide switch: BNC or terminal block
Distance
Ethernet: 1000 Meters, PoE: 600 Meters (Max) based on cables
Power Input
Terminal Block orange color x1
Terminal Block black color x1
Input Voltage
PoE injector/Switch 802.3at/af PoE or DC 48V/DC56V power adapter
Power output
Terminal Block green color x1
Terminal Block orange color x1
Output Voltage
x
DC12V
LED Indication
Power, POE, Ethernet, Status
Protection
ESD Protection: 30KV, 1KA @ 8/20us
Data Rate (Max)
Uplink：70Mbps , Downlink：
71Mbps
Uplink：71Mbps, Downlink:70Mbps
Power Consumption
2.5W
3W
Temperature
Operation: -10 to 65℃, Storage: -20 to 70℃, Humidity: up to 95%
Dimension mm
109.6 x 131.5 x 30
109.6x131.8x30
Weight g
280
Rev. B 20170327
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Smart Cabling & Transmission Estensione
