USER OPERATING INSTRUCTIONS
SMARTPOINT SMARTLINC II
Biometric Recognition Safe Locking System
OPENING THE LOCK (WITH FINGER ONLY ACCESS WITHOUT TIME DELAY)
OPENING THE LOCK (WITHOUT TIME DELAY)
1. Press any key to power up SMARTPOINT.
+ Display will show either “ENTER CODE” or SELECT LOCK” when two or more locks are installed.
2. Select lock if two or more locks are installed, display will show “P TO SCAN, OK FOR CODE”.
3. Press P key, display will show “SCAN YOUR FINGER”.
+ If a valid ngerprint is entered, display will show “LOCK = 1, OPEN!”.
+ If Lock is set with Open Oset, the display will show “LOCK = #, OFFSET = ##”, and will show the
counting sequence to the Oset.
4. Open the Door within 3 seconds.
+ Before power-o, display will show current date and time.
+ If an invalid ngerprint is scanned or the ngerprint was not placed directly on the scanner, the
display will show ”FINGERPRINT ERROR!”.
+ Display will power-o after 30 seconds of non-operation.
1. Press any key to power up SMARTPOINT.
+ Display will show either “ENTER CODE” or “SELECT LOCK” when two or more locks are installed.
2. Select lock if two or more locks are installed.
3. Enter a valid 6 (six) digit User Code (and scan nger, if set-up)
+ If a valid code/nger is entered, display will show “LOCK = 1, OPEN!”.
+ If Lock is set with Open Oset, the display will show “LOCK = #, OFFSET = ##”, and will show the
counting sequence to the Oset.
4. Open the Door within 3 seconds.
+ Before power-o, display will show current date and time.
+ If and invalid code is entered, display will show “NOT VALID USER!”.
+ If an invalid ngerprint is scanned or the nger was not placed directly on the scanner, the display
will show ”FINGERPRINT ERROR!”.
+ Display will power-o after 30 seconds of non-operation.
SELECT LOCK
XX
P TO SCAN
OK FOR CODE
SCAN
YOUR FINGER
LOCK = 1
OPEN!
FINGERPRINT
ERROR!
NOTE: IF THERE IS A LOCK SET TO AUTO OPEN - In a multiple lock system you can set an outer door lock to AUTO OPEN. This will allow the user (if
authorised) to open the inner compartment lock and have the outer door lock automatically open. The AUTO OPEN lock always opens rst.
NOTE: IF THERE IS A LOCK SET TO AUTO OPEN - In a multiple lock system you can set an outer door lock to AUTO OPEN. This will allow the user (if
authorised) to open the inner compartment lock and have the outer door lock automatically open. The AUTO OPEN lock always opens rst.
NOTE: If there is a user who ngerprint is unable to be read, by pressing OK they can enter their code and scan their print. The
system will do a one-to-one match.
SELECT LOCK
XX
ENTER LOCK
X-X-X-X-X-X
LOCK = #
OFFSET = ##
LOCK = 1
OPEN!
NOT VALID USER!
FINGERPRINT
ERROR!
OPENING THE LOCK (WITH TIME DELAY)
1. Press any key to power up SMARTPOINT.
+ Display will show either “ENTER CODE” or SELECT LOCK” when two or more locks are installed.
2. Select lock if two or more locks are installed.
3. Enter a valid 6 (six) digit User Code (and scan nger, if set-up)
+ If Time Delay has been set, display will show “STARTING, TIME DELAY” and then “LOCK = #, DELAY
MM:SS”
+ Counting is updated every second, if displayed.
+ Press “P” to abort Time Delay, display will show “CANCEL, TIME DELAY?” Press OK, display will
show, “TIME DELAY, CANCELLED”.
+ After Time Delay has elapsed, the display will show “P TO SCAN, OK FOR CODE” and then “#X
MM:SS, x-x-x-x-x-x” (open window counting time).
4. During the open window, enter a valid code (and scan nger, if set-up) to open.
+ If a valid code is entered, display will show “LOCK = 1, OPEN!”.
SELECT LOCK
XX
ENTER LOCK
X-X-X-X-X-X
STARTING
TIME DELAY
LOCK = #
DELAY MM:SS
CANCEL
TIME DELAY?
V1.0_9102 | Division of Davcor Group Pty Ltd | www.smartlock.com.au | www.smartlock.co.nz | Page 2
