SmartRG SR515ac Manuale utente

SR515ac

Quick Start Guide

Installation

1. Connect your gateway to the incoming service wall jack:

lIf an RJ45 cable is included with your gateway, connect one end to the DSL port on the gateway and

connect the other end to the wall jack.

lIf a splitter is included with your gateway, connect one end of the splitter to the DSL port of the gateway

and connect the other ends to the wall jacks: one for the phone jack and one for the Internet service.

2. Connect a LAN port of the gateway to your PC using an Ethernet cable.

3. Plug the power adapter into the wall outlet and connect the other end of it to the Power port of the gateway.

4. Turn on the unit by pressing the power button on the back of the gateway.

Note: If you use 3G WAN service, connect the 3G USB data card to the USB port of the gateway. If you use the Ethernet

uplink, connect the WAN port that is defined to the Internet with an Ethernet cable. The xDSL uplink, 3G WAN service,

and Ethernet uplink cannot coexist.

Your gateway is now automatically being set up to connect to the Internet. This process may take a few minutes to

complete before you can begin using your Internet applications (browser, email, etc.).

If you are unable to connect to the Internet, confirm that all connections are in place and the gateway’s power is

turned on.

DSL WAN USB

COAX

DC/

LAN

5 min

LED Indicators

The LEDs on the SR515ac can assist you in better understanding

the current state of your gateway.

Legend: On Off Blinking

POWER LAN 1-4 WLAN DSL INTERNET

DSL sync in progress

DSL sync acquired and gateway online

Gateway online and data transfer in progress

IP connection failure

WiFi enabled on modem

PC / network activity / data transfer

WPS Setup procedure in progress

WPS Connection completed successfully

Quick Gateway Configuration

Warning: Do not press the Reset button unless you want to clear the current settings. The Reset button is in a small

circular hole on the rear panel. If you want to restore the default settings, insert a thin wire (such as a paper clip) into

the hole, press the Reset button gently for 1 second, and then release the button. The system reboots and returns to

the factory defaults.

Logging in to your gateway

To change the settings on your gateway, you must log in to the gateway's interface. Make sure that you have completed

the steps in "Installation" before you begin.

1. Open your internet browser application and type 192.168.1.1 into the address line. The login dialog appears.

2. Enter the default username and password: admin/admin, and click OK. The Device Info summary page appears.

Note: Your service provider may use other settings. Please contact your provider for login information.

Configuring the WAN manually

If the automatic connect process is unsuccessful, refer to the Advanced Setup >Layer 2 Interface and WAN Services

sections of the SmartRG SR3xx - SR5xx Gateway User Manual to manually establish a connection.

WiFi Setup

Two methods, WPS and Manual, are available for WiFi setup. Perform the steps on this page first, and then follow

the instructions for the applicable method.

1. In the left menu, click Wireless and then click 2.4 GHz Band or 5 GHz Band. The Wireless > Basic page appears.

The fields are the same for both options. The wireless radio is enabled by default.

2. If Enable Wireless is not selected, select it now.

3. In the SSID field, select the SSID that you want to use.

4. Click Apply/Save.

5. Continue with the steps for the method you prefer.

WPS Method

If the device you wish to connect to the Internet via your gateway supports the WPS secure WiFi connection method,

follow these steps.

1. In the left navigation bar, click Wireless > the wireless band you want to configure, and then click Security.

2. In the Enable WPS field, select Enabled.

3. Click Apply/Save to commit your selection.

4. On the left side of the gateway, press the button labeled WPS.

lTo activate the 2.4 GHz band, press the button for 1-3 seconds.

lTo activate the 5 GHz band, press the button for 5-7 seconds.

5. Within 2 minutes, activate WPS on the 3rd party device to which you wish to connect. The device may have a

push button on its exterior that you can press, or a clickable button on a software interface. To learn how to use

the WPS feature on your client device, refer to its documentation.

Your device should now be connected to your gateway wirelessly using WPS. If you encounter problems with the WPS

setup such as connection failure, refer to your client device for further instructions.

Manual Method

Set up your gateway’s parameters first, then follow these steps.

1. In the left navigation bar, click Wireless > the wireless band you want to configure, and then click Security.

2. Scroll down to the Manual Setup AP section.

3. If your gateway supports multiple wireless networks, select the SSID of the network you wish to configure. You

will need this ID for step 7.

4. Select the desired Network Authentication. Make sure that the host devices you intend to use support the

selected authentication type.

5. Choose a WPA Passphrase and type it in to this field. You will need this passphrase for step 7.

6. Select any desired encryption preferences in the lower three fields.

7. Click Apply / Save.

8. Follow the WiFi connection instructions provided with your client device to connect to the router. Use the SSID

name you selected in Step 2 and enter the same passphrase that you entered in step 4 to set up the connection

on your client device.

Altri manuali per SR515ac

Indice

Altri manuali SmartRG Router di rete

SmartRG

SmartRG SR512nm Manuale utente

SmartRG

SmartRG SR630N Manuale utente

SmartRG

SmartRG SR320n Manuale utente

SmartRG

SmartRG SR310N Manuale utente

SmartRG

SmartRG SR505n Manuale utente

SmartRG

SmartRG SR510n Manuale utente

SmartRG

SmartRG SR655ac Manuale utente

SmartRG

SmartRG SR506n Manuale utente

SmartRG

SmartRG SR616ac Manuale utente

SmartRG

SmartRG DB120-WL Manuale utente

SmartRG

SmartRG SR505n Manuale utente

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

TP-Link

TP-Link TD-8817 Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

Cisco

Cisco NCS 540 Manuale

XAVi

XAVi X8821e Manuale utente

BEC

BEC 6200WZL Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

Cisco

Cisco ASR 1000 Series Manuale dell'operatore

EnGenius

EnGenius ESR-9710 Manuale utente

Cisco

Cisco 805 Series Istruzioni operative e di sicurezza