Smeg DD612SC Manuale utente
INSTRUCTION MANUAL
G
GU
UI
ID
DE
EF
FO
OR
RU
US
SI
IN
NG
GT
TH
HE
ED
DI
IS
SH
HW
WA
AS
SH
HE
ER
RA
AN
ND
DT
TH
HE
EW
WA
AS
SH
HI
IN
NG
GP
PR
RO
OG
GR
RA
AM
MS
S
Contents
1. Description of the controls________________________________14
2. Troubleshooting _______________________________________21
Thank you for choosing one of our products.
You are advised to read this manual carefully; it contains all the
information you need about the right conditions for the proper, safe use
of your dishwasher.
The individual sections are laid out to provide you with a step-by-step
guide to all your appliance's functions; the texts are easy to understand
and are complete with detailed illustrations.
This user-friendly manual will provide answers to all your questions
about use of the dishwasher.
For any other information about use and maintenance of the dishwasher,
read the enclosed manual carefully.
USER INSTRUCTIONS: useful information is provided for the use of the
washing programs and all the dishwasher's functions.
User instructions
1. Description of the controls
1.1 Front panel
All the dishwasher control are grouped on the front panel.
1ON/OFF BUTTON
2SELECTION PROGRAMS BUTTONS (P1...P5)
3POWER ON LIGHT
4PROGRAMS LIGHTS
5NO SALT LIGHT (depending on the models)
6NO RINSE AID LIGHT (depending on the models)
7PHASES/PROGRAM LIGHTS
8RECESSED DOOR HANDLE
User instructions
DURATION CONSUMPTION
PROGRAM SELECTION TYPE AND GRADE DIRT PROGRESS
PROGRAM MINUTES
(2)
WATER
LITRES (1)
POWER
KWh (2)
SOAK
PANS AND DISHES
IN WAITING OF
COMPLETING
THE LOAD
Cold prewash 15' 60,03
LIGHT DISHES
NOT VERY DIRTY
Wash at 45°C
Cold rinse
Rinse at 68°C
Dry
70' 121,00
BIO
(*)
PANS AND DISHES
NOT VERY DIRTY BUT
WITH DRY RESIDUALS
Cold prewash
Wash at 50°C
Cold rinse
Rinse at 65°C
Dry
170' 171,05
NORMAL
PANS AND DISHES
DIRTY AND WITH
DRY RESIDUALS
Cold prewash
Wash at 65°C
Cold rinse
Rinse at 68°C
Dry
90' 17 1,30
SUPER
PANS AND DISHES
VERY DIRTY AND
WITH DRY RESIDUALS
Prewash at 45°C
Wash at 70°C
2 cold rinses
Rinse at 70°C
Dry
110' 201,60
Only run the soak program with half loads.
(*) Reference program as per EN 50242 standard.
(1) Average power consumption with the softener set on level 2.
(2) The cycle duration and power consumption may vary according to the water and room
temperatures, and the type and amount of dishes.
The washing cycle will not take place if the dishwasher door is left open
or not properly closed.
User instructions
1.2 Washing programs
The dishwasher is equipped with a control panel, described in chapter
"1. Description of the controls", from which it is possible to carry out all
the power switch-on, switch-off and programming operations.
Before starting a washing program make sure that:
•The water supply tap is open.
•The correct amount of detergent has been added to the
dispenser.
•The baskets have been correctly loaded.
•The spray arms are able to rotate freely and without
obstruction.
•The dishwasher door is securely closed.
LIGHTING
When the ON/OFF button (1) is pressed, the dishwasher switches on
and the light (3) comes on. About 2 seconds later, the
PHASES/PROGRAM lights (7) will come on.
PROGRAMMING
In this model of dishwasher, all programming procedures can only be
carried out with the door closed. As long as the door is open, the
PROGRAMS lights (4) and PHASES/PROGRAM lights (7) will remain
off.
SELECTION PROGRAM
The program selection is possible
through the relative buttons (2).
When the button relating to the program required is pressed, the relative
light will come on to confirm the operation.
User instructions
START PROGRAM
To start the dishwasher, press the button of the PROGRAM (2) required
for a few seconds, until the light of the first phase of the selected
program starts to flash (confirmation beep).
As the program runs, the PHASES/PROGRAM lights (7) will indicate the
current cycle status.
The light of the phase in progress will
flash, while the lights of the previous and
subsequent phases remain on.
N.B. during execution of programs which
do not include a prewash, the first
PHASES/PROGRAM light (7) will remain
off.
END PROGRAM
When the program finishes, a buzzer sounds
briefly and all the PHASES/PROGRAM lights
(7) flash.
Press any of the SELECTION PROGRAMS buttons (2), stops the light
flashins, and the dishwasher is now ready to perform a new cycle;
opening and shutting the door or switching the appliance off and on has
the same effect.
Pr
e
w
as
h
W
as
h
Rinse
Dr
y
User instructions
INTERRUPTION OF A PROGRAM
In order to interrupt a running program it is necessary:
•press one of the SELECTION PROGRAMS buttons (2), the light of
the current phase will go out;
•keep the button pressed until the PHASES/PROGRAM lights (7)
come on (confirmation buzzer);
•start the program (see “START PROGRAM”).
TO CHANGE A PROGRAM
To change the running program it is necessary:
•to interrupt the running program (see “INTERRUPTION OF A PROGRAM”);
•select the new program;
•start the program (see “START PROGRAM”).
ANNULLING A PROGRAM
To annul the program in progress, it must first be interrupted (see
“INTERRUPTION OF A PROGRAM”).
Now press buttons P1+P2 simultaneously and
the first three program lights will come on.
In case that the door is opened during the operation, to the next door
closing it is going to be necessary to start the program as shown in
paragraph “START PROGRAM”. The program will resume from the point in
which it was interrupted.
In case that the tub temperature is higher than 50°C the program
will start about 30 seconds later.
User instructions
TO SAVE ON ENERGY! … AND PROTECT THE ENVIRONMENT
•Always try to run the dishwasher fully loaded.
•Do not wash the dishes in running water.
•Use the washing program that is most appropriate for each type of
load.
•Do not carry out any preliminary rinsing.
•If available, connect the dishwasher to a hot water supply up to
60°C.
TO CUT DOWN ON DETERGENT CONSUMPTION! … AND PROTECT
THE ENVIRONMENT
The phosphates contained in dishwasher detergents are harmful to the
environment. To avoid using excessive amounts of detergent and to
save on electricity, observe the following:
•separate the more delicate items from dishes that are more
resistant to aggressive detergents and high temperatures;
•do not pour the detergent directly on the dishes.
REMOVING THE DISHES
At the end of the washing program, wait at least 20 minutes before
removing the dishes, to allow them to cool down. To prevent any water
droplets on the upper basket from falling on the dishes in the lower
basket, it is advisable to unload the lower basket first, and then the
upper basket.
User instructions
ADJUSTING THE WATER SOFTENING SYSTEM
The dishwasher is equipped with an device for the user to adjust the
water softening system according to the hardness of the water supply.
According to the machine model, the selector which acts on the
adjustment may be located:
•inside the plastic locking ring located on the right-hand side, inside
the dishwasher;
•inside the water softener, just below the cap.
Both allow for adjustment to 5settings:
WATER HARDNESS TABLE
WATER HARDNESS
German Degrees (°dH) French Degrees (°dF) SETTING
0 - 4 0 - 7 Setting N. 1 NO SALT
5 - 15 8 - 25 Setting N. 1
16 - 23 26 - 40 Setting N. 2
24 - 31 41 - 60 Setting N. 3
32 - 47 61 - 80 Setting N. 4
48 - 58 81 - 100 Setting N. 5
Contact your local water board for information on the hardness of your
water supply.
User instructions
2. Troubleshooting
In case of a malfunction, the dishwasher will identify the program by
switching on a combination of lights.
When an alrm is present, all the
PROGRAM lights (4) come on, while the
PHASES/PROGRAM lights (7) identify
the error code:
CODE PHASES LIGHTS DESCRIPTION
E1 The anti-flooding system (if installed) has been
tripped.
E2 The system which limits the water level inside the
dishwasher (safety unit) has been tripped.
E3 The appliance cannot heat the water.
E4 Temperature sensor disconnected.
E5 The appliance is not able to take in water.
E6 The appliance is not able to pump out the water
from the tank.
E7
The appliance is not able to measure the amount
of water loaded accurately (on models with turbine
flow-regulator only).
E8 Anomaly in the system which distributes water to
the basket (where installed).
E9
The maximum level of water for loading has been
exceeded (on models with turbine flow-regulator
only).
Questo manuale è adatto per i seguenti modelli
11
Indice
Altri manuali Smeg Lavastoviglie
Smeg
Smeg LSA6545B Manuale utente
Smeg
Smeg Dishwasher DF41-7 Manuale utente
Smeg
Smeg ST663 Manuale utente
Smeg
Smeg STX.1 Manuale utente
Smeg
Smeg ST5324L Manuale utente
Smeg
Smeg DWA6214S Manuale utente
Smeg
Smeg Dishwasher VG612462 Manuale utente
Smeg
Smeg Dishwasher CSU2001B1 Manuale utente
Smeg
Smeg DF352CW Manuale utente
Smeg
Smeg LSA6051B Manuale utente
Smeg
Smeg DWD64.1SS Manuale utente
Smeg
Smeg ST4107 Manuale utente
Smeg
Smeg ST45 Manuale utente
Smeg
Smeg Dishwasher DWD64.1BL Manuale utente
Smeg
Smeg DI6012-1 Manuale utente
Smeg
Smeg STA8643 Manuale utente
Smeg
Smeg ST66T Manuale utente
Smeg
Smeg CSE66-I2 Manuale utente
Smeg
Smeg LVS262EB Manuale utente
Smeg
Smeg DI6FABNE Manuale utente
