Smittybilt Q89 Manuale utente
For Technical Support/Warranty Information please call 310-762-9944
Smittybilt, 400 West Artesia Blvd, Compton, CA 90220
Installation Instructions
(Part # Q89)
Dual Cylinder Air Compressor
WWW.SMITTYBILT.COM
SPECIFICATIONS:
Motor: 12-Volt DC
Maximum working pressure: 120psi.
Maximum re-start pressure: 90psi.
Maximum continuous operating time is 40 minutes.
Recommended on/off cycle time: 20/40 minutes
Overheating Protection Circuit:
The unit is equipped with an automatic protection device. In the event the unit reaches an unsafe operating
temperature, a protection circuit will cut power to prevent damage to the unit. If the protection circuit
activates, immediately disconnect the unit from the power source and allow it to cool.
The unit will cool in approximately 15 minutes, depending on environmental conditions. The protection
circuit will automatically reset itself when the temperature returns to a safe operating level.
High altitude and certain air temperatures can negatively affect the unit’s performance.
WARNINGS:
WARNING! READ ALL INSTRUCTIONS before operating product. Failure to follow all
instructions below may result in electrical shock, fire and serious injury or death.
WARNING! Always wear ANSI Z87.1 approved safety glasses with side shields when operating.
Compressed air and particulate matter can cause eye and soft tissue damage. Keep air
stream away from skin and eyes.
WARNING! RISK OF BURNS: Always wear gloves. Some exposed parts may become hot during
use.
WARNING! RISK TO BREATHING: This compressor is not designed for and never should be
used as a source of breathable air.
WARNING! RISK OF ELECTRICAL SHOCK: This compressor is for use in dry conditions
only.
WARNING! RISK OF FALLING: This compressor will produce vibrations and can “walk.” Only
operate at ground level.
For Technical Support/Warranty Information please call 310-762-9944
Smittybilt, 400 West Artesia Blvd, Compton, CA 90220
Installation Instructions
(Part # Q89)
Dual Cylinder Air Compressor
WWW.SMITTYBILT.COM
WARNING! RISK OF FIRE: This unit will become hot during operation. Allow to cool before
storing.
WARNING! RISK OF BURSTING: Use only accessories rated for 120 psi. Always follow tire
manufacturer’s recommended inflation instructions. In most cases they can be located
on the side wall of the tire. If you are unsure, contact the manufacturer.
WARNING! DO NOT MODIFY: Never drill, modify or attempt to repair the unit. There are no
user serviceable parts inside.
WARNING! SAFE HANDLING: Never carry the unit by the hose or power cord.
WARNING! PAY ATTENTION: Do not leave the unit running unattended.
WARNING! California Proposition 65 Warning! This product or its power cord contains lead, a
chemical known to the State of California to cause cancer and birth defects or other
reproductive harm. Wash hands after handling.
Hard Mounting:
This unit may be hard mounted in a dry location. Be sure to use proper size wiring for your application. When
using this unit with an air tank, you must install a back-flow preventing device to prevent damage to the
cylinder head air valve.
EXTRA CAUTION:
Small items will inflate quickly and can easily be damaged. Pay special attention to bicycle tires. They
inflate very fast and can rupture. Be prepared to stop the unit quickly when manufacturer’s
recommended inflation pressure is reached.
Operating Warning:
This unit is designed to supply continuous flow of air. Never dead end the hose or use accessory that stop the
free flow of air. Damage to the unit can occur.
For Technical Support/Warranty Information please call 310-762-9944
Smittybilt, 400 West Artesia Blvd, Compton, CA 90220
Installation Instructions
(Part # Q89)
Dual Cylinder Air Compressor
WWW.SMITTYBILT.COM
Operation:
When operating the unit, be sure to be in a safe location off of the roadway and away from traffic.
Step One: Unpack the unit and inspect for damage. Fully unwrap the power cord.
Step Two: Place the unit on a dry level surface. Attach the air filter to the front of the unit and finger
tighten.
Step Three: Connect the air supply hose to the unit using the quick connect fitting.
Fig #1. Slide retaining snap ring back.
Fig #2. Slide the fittings together firmly.
Fig #3. While holding fittings together firmly slide the outer ring forward to lock.
Fig #1 Fig #2 Fig #3
Step Four: Connect the Red power clip to a Positive 12 volt source.
Connect the Black power clip to a Negative ground point.
Step Five: Test the connections by switching the compressor to “on.” Air will begin to flow.
Step Six: Connect the air hose by screwing the brass inflator onto the tire valve stem. Only finger tighten
the inflator. Do not use any tool as you may damage the inflator or the valve stem.
Step Seven: Watch the gauge closely, switch the unit off or remove the inflator from the tire when the
manufacturer’s recommended pressure has been achieved. We recommend that you use a
second tire pressure gauge to verify your tires are inflated to the proper pressure.
CAUTION: Stopping and restarting at high pressure can overload and blow the in-line fuse. At higher
inflation pressures, start the unit and then attach to the filler to the tire valve stem. If you stop the unit and
need to resume inflation, remove the inflator tip from the tire valve, start the unit and reattach with the unit
running.
For Technical Support/Warranty Information please call 310-762-9944
Smittybilt, 400 West Artesia Blvd, Compton, CA 90220
Installation Instructions
(Part # Q89)
Dual Cylinder Air Compressor
WWW.SMITTYBILT.COM
Step Eight: Allow the compressor to cool and place neatly in the carry bag with the clips securely fastened
to the loops on the carry bag. To prevent damage to the unit during storage repack in the
original Styrofoam and color box. Store the unit in a dry location.
Step Nine: Remember to replace the valve cover on the stem.
Operating Hints:
Turn the compressor on before connecting to the tire in order to reduce stress on the motor.
We recommend an on\/off cycle time of 20 minutes rest/off for every 40 minutes of run time.
To prevent damage to the air hose fitting, remove the inflator from the tire before disconnecting the hose from
the compressor.
Troubleshooting:
If the unit stops during operation:
1. Check the battery condition. Low voltage can blow the fuse or trigger the protection feature.
2. Check the circuit breaker reset if necessary.
3. The unit is equipped with an automatic protection device. In the event the unit reaches an
unsafe operating temperature, a protection circuit will cut power to prevent damage to the
unit. If the protection circuit activates, immediately disconnect the unit from the power
source and allow it to cool.
Resetting Circuit Breaker:
The circuit breaker is located next to the on/off switch. During normal operation it remains
in the down position almost even with the base. In the event of and overload it will pop-up.
If this happens, turn the power switch to off, disconnect the air hose and power cord. Push
the breaker down to reset and resume operation.
If air is leaking from inflator end:
1. The inflator end has a dual function, to inflate and deflate your tire. Be sure to fully extend
the brass inflator to inflate your tire. Push back and turn the brass end to deflate.
2. Inspect inside the ez twist inflator for damage to the O rings. If they are damaged contact
Smittybilt for a replacement hose.
For Technical Support/Warranty Information please call 310-762-9944
Smittybilt, 400 West Artesia Blvd, Compton, CA 90220
Installation Instructions
(Part # Q89)
Dual Cylinder Air Compressor
WWW.SMITTYBILT.COM
Smittybilt’s products are covered under the following limited warranties only. Note that the duration of the limited warranty differs
according to the material and finish of the product purchased. Subject to the duration and conditions of the limited warranty stated
below, Smittybilt warrants to the original retail purchaser that its products are free from defects in material and workmanship. All
other warranties and representations express or implied are hereby disclaimed, including fitness for merchantability and buyer’s
intended use or purpose. All parts are sold “AS IS” except for the limited warranties granted herein. Buyer assumes all risks as to
the selection, suitability and performance of all goods and products selected. This limited warranty does not cover damage or
impairment in any part due to misuse, improper installation, accident or contact with on-road or off-road hazards, product
modification, improper or inadequate cleaning and/or maintenance. Smittybilt is not responsible for items damaged during
shipping. This warranty is not transferable from the original buyer. For the original Buyer to be eligible for the limited warranty
coverage, the Buyer must provide proof of purchase. Smittybilt strongly recommends returning the warranty registration card.
Customer’s remedy hereunder shall be limited only to repair or replacement (at Smittybilt’s option) of any defective part(s) returned
to Smittybilt at customer’s expense. The determination of whether or not a returned part is defective or subject to coverage under
the limited warranties stated herein shall be made at Smittybilt’s sole discretion.
Duration of Limited Warranty
1. Limited Lifetime Warranty on Stainless Steel Products -
Smittybilt stainless steel products carry the foregoing limited repair or replacement warranty against workmanship and defects
in the material so long as the original purchaser retains the original stainless steel parts.
2. Limited Five (5) Year / 50,000 Mile Pro-Rata Warranty (whichever occurs first) on Dual-Stage Powder Coating
Products -
Smittybilt dual-stage powder coated products carry the foregoing limited repair or replacement warranty for a period of (5)
years or 50,000 miles (whichever occurs first) from date of purchase against workmanship and defects in the material, provided
that any claim submitted after (2.5) years from date of purchase shall, if accepted, be satisfied by Smittybilt offering customer a
credit on the purchase of a replacement product equal to fifty percent (50%) of customer’s initial purchase price.
3. Limited Three (3) Year / 36,000 Mile Pro-Rata Warranty (whichever occurs first) on Chrome Products -
Smittybilt chrome products finished carry the foregoing limited repair or replacement warranty for a period of three (3) years or
36,000 miles against workmanship and defects in the material (whichever occurs first) from the date of purchase.
Requesting Warranty Coverage
To make a claim under this limited warranty, customer must:
(1) Call Smittybilt, at (888) 717-5797 for a return authorization code (RAC) and/or Smittybilt may require photographic proof of
defect before issuing an (RAC); (2) return the defective part, properly packaged to prevent further damage to the product, postage
prepaid, together with dated proof of purchase receipt and identifying return authorization code (RAC) on the outside of the
packaging to Smittybilt at 1600 Walnut Parkway, Compton, CA 90220. Warranty claims cannot be determined until the returned
merchandise is inspected. A minimum charge of fifteen percent (15%) may be added for all products which are determined to be
returned for reasons other than warranty. Additional charges may be applied if merchandise is damaged or unsellable upon receipt.
Indice
Altri manuali Smittybilt compressore d'aria
