SMK-Link Bluetooth Stopwatch Presenter Manuale utente
Page 1
User’s Manual
Wireless Stopwatch Presenter with
Laser Pointer
Page 2
Regulatory Compliance
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired
operation.
FCC Certication
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant
to Part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful
interference when the equipment is operated in a
residential installation. This equipment generates,
uses and can radiate radio frequency energy and,
if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio
or television reception, which can be determined by
turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
•
•
Page 3
Consult the dealer or an experienced radio/TV
technician for help.
Notice: Any changes or modications not expressly
approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
Extension cables are not recommended, if used, they
must be shielded in order to comply with the emission
limits.
IC Certication
The term “IC” before the certication/registration
number only signies that the Industry Canada technical
specications were met.
Declaration of conformity
Hereby, SMK-LINK Electronics Corporation, declares
that this product is in compliance with the essential
requirements and other relevant provisions of Directive
1999/5/EC.
All trademarks and registered trademarks mentioned
in this document are the property of their respective
owners.
Features and specications are subject to change without
notice.
© 2008 SMK-LINK Electronics, Inc.
•
Page 4
System Requirements
Hardware: 1 available USB port
Operating System: Windows 2000, XP or Vista
Macintosh OS X or above (F5 SlideShow and Alt-Tab
Application Switch not supported)
Package Contents
Wireless 2.4 GHz stopwatch presenter
Micro USB receiver dongle (stored inside
presenter)
2 x AAA batteries
User’s manual
Carrying case
Installing the Rechargeable
Batteries (Supplied)
•
•
•
•
•
Sliding the battery cover off Insert batteries to the correct
polarities
Page 5
Open the battery compartment by pressing
down the cover latch and sliding the door off
the presenter.
Insert the two supplied AAA batteries
(included in the package) to the battery slots.
Make sure the positive (+) and negative
(-) ends of the batteries match the polarity
markings inside the battery compartment.
Close the battery cover back into position.
Connecting the Presenter to
the Computer
Retrieve the micro USB receiver dongle
from the built-in storage located at the top-
end of the presenter.
•
•
•
•
Top View of the Presenter
USB Receiver
Page 6
Connect the micro USB receiver dongle to
an available USB port on your computer.
Wait for the computer to go through its
default process of recognizing the new
hardware and installing the built-in native
driver. You don’t need to do anything
while your computer is going through the
installation of a new device.
Power on the presenter by sliding the
on/off switch to ON position.
•
•
On/off Switch
Power switch on the presenter
Page 7
The radio frequency (RF) codes are
factory preset for your convenience; the
presenter should be functional at this
point.
If for any reason the presenter does not
function correctly, i.e. the presentation
slides do not advance to the next page,
there may be other wireless devices
in the vicinity operating in the same
radio frequency channel. The presenter
can easily be reset to another channel
by pressing once on the USB receiver
dongle’s connect button while it’s plugged
in to the computer’s USB port, followed
by pressing once on the connect button
located at the bottom of the presenter.
This will switch the presenter and the
receiver to a different channel to avoid
interference. This step can be repeated
when needed.
•
•
Page 8
Using the Presenter
Connect Button
(1) Press the connect button on the receiver
(2) Press the connect button on the presenter
Dongle StorageLaser Beam
On/off
Application Switch
Previous Page
Dark Screen
Slideshow/Esc
Next Page
Laser Pointer
Scroller/LCD Display Backlit
LCD Time Display
Stopwatch
Page 9
F5/Esc
Slideshow toggle key starts a
slideshow (F5) and exits from a
slideshow (Esc). Note: in
PowerPoint slideshow starts with
page 1 when resumed in the middle
of a presentation.
Next Page key to advance to the
next slide.
Previous Page key to return to the
previous slide.
Application Switch (Alt-Tab) key
displays all the open windows and
switches to the desired window by
pausing over the selected window
icon for 3 seconds.
Dark Screen toggle key blackens the
screen and resumes the presentation.
Laser Pointer key triggers the laser
beam. The laser beam emits for the
duration that you press the key.
Scroller on the side allows the presentation
of a long document such as an Excel le.
Scrolling one notch up or down advances one
line at a time. To advance in rapid mode press
•
•
•
•
•
•
•
Page 10
up or down on the scroller for more than 1
second at a time. In PowerPoint the scroller
serves as an alternative key for Next Page and
Previous Page.
Stopwatch control and LCD display (H:MM)
When presenter power is turned on:
stopwatch on standby and LCD display turns
on (the Hour and Minute separator “:” is
constant.)
If stopwatch is not activated within 1 minute
it automatically turns off. To turn on the
stopwatch function, press the stopwatch
button once. Note: the stopwatch is not yet
activated.
To activate the stopwatch press the
stopwatch button once; the Hour and
Minute separator “:” ashes and the LCD
display shows time advancing by 1 minute
increment.
To pause the stopwatch, press the stopwatch
button once; the Hour and Minute separator
“:” stops ashing.
To resume the stopwatch, press the
stopwatch button once more; the Hour and
Minute separator ashes again and the time
•
•
•
•
•
•
Altri manuali per Bluetooth Stopwatch Presenter
1
Indice
