Snapper 1695195 Manuale utente

Hydraulic

Lift

Manual Lift

(Add to early models

already present on

current models)

Front Hole for Dozer Applications

Rear Hole for Snowthrower Applications

Installation

Instructions

Sub-Frame Hitch

Mfg. No. 1695195

For Prestige / 1800 / 2800 & Conquest / 1700 / 2700 Series

Figure 1. Contents

Kit Contents:

Ref Part No. Qty. Description

1 1733779A 1 PUSH BAR ASSEMBLY

2 1733812 2 ROD - HITCH

3 2176012 5 SAFETY CLIP

4 1723292A 1 HOOK ASSEMBLY

5 1653768A 1 CLAMP

6 2171011 1 SPRING, Compression

7 1931335 4 CARRIAGE BOLT, .31 X 1

8 1919381 4 WASHER

9 1917356 4 LOCKWASHER, .31

10 1917372 4 NUT - FULL .31-18

11 1724025A 1 LEVER ASSY - LIFT

12 2105249 1 PIN, CLEVIS

Ref Part No. Qty. Description

13 1722469 1 LOCKDOWN, HYD.

14 1722819 1 PIN, CLEVIS

15 1960033 1 CLIP, HAIRPIN

16 1722946 1 ROD, LIFT

17 8031007 2 SET, COLLAR

18 1928721 2 SCREW, .31-18 X .50

19 1723115 1 GUIDE ASSY., ROD

20 1723309 1 ROD, HITCH

21 1723795A 1 BAR, LIFT

22 1960074 2 CLIP

23 1921210 4 SCREW, .38-16 X 1

24 1928352 4 NUT, FLG, .38-16

25 1733814A 1 PUSH BAR LATCH

14 13

23 3

This kit is required when installing front-mounted

attachments.

17 6

18 18

Installation Instructions Sub-Frame Hitch

Figure 3. Assemble Lift Rod

A. Lift Rod C. Spring

B. Set Collar D. Rod Guide

NOTE: Please read through these instructions and the

instructions of any other attachments before beginning

installation.

INITIAL ASSEMBLY

Assemble Hitch

1. Attach the support clamp (C, Figure 2) and hook

assembly (B) to the hitch. Secure with four 5/16-18 x

1 carriage bolts (A), washers (D), lockwashers (E),

and nuts (F). Do not tighten the hardware at this

time.

WARNING

Before beginning any service work turn off the

PTO, set the parking brake, turn off the ignition,

and disconnect the spark plug wire(s).

Figure 2. Install Support Clamp

A. 5/16-18 x 1 Carriage Bolt D. 11/32 Washer

B. Hook Assembly E. 5/16 Lockwasher

C. Support Clamp F. 5/16-18 Nut

Broadmoor /

1600 / 2600

Series

Conquest / 1700 /

2700 &

Prestige / 1800 /

2800 Series

Assemble Lift Rod

1. Install the set collars (B, Figure 3), spring (C), and

rod guide (D) on the lift rod (A) as shown. Final

adjustment of the set collars will be made after the

hitch and attachment are installed.

Assemble Push Bar Latch

1. Attach Push Bar Latch (B, Figure 4), to hitch. Secure

with four .31-16 x 1 bolts (A), and four .38-16 flange

nuts (C).

FourWheel

Drive Models

TwoWheel

Drive Models

Figure 4. Assemble Push Bar Latch

A. Bolt, .38-16 x 1 C. Flange Nut, .38-16

B. Push Bar Latch

Sub-Frame Hitch Installation Instructions

FCD

Figure 6. Lift Link - Manual Lift Models

A. Pin

B. Rear Hole of Lift Bar (Snowthrower/Dozer

Applications)

C. Spacer

D. Hair Pin Clip

E. Upper Hole (Snowthrower/Dozer Applications)

F. Slot of Lift Link (Mower Applications)

G. Lower Hole (Mower Applications)

BCD

Snowthrower

& Dozer

Applications

Mower

Applications

Figure 5. Lift Lock Plate - Hydraulic Lift Models

A. Lift Cylinder

B. Flat Head Pin (Original)

C. Flat Head Pin (New)

D. Lock Plate

E. Hair Pin Clips

F. Lift Shaft Assy.

G. Washers

BCDF

Install Downward Pressure Lock

HYDRAULIC LIFT MODELS

1. Install the downward pressure lock plate (D, Figure 5)

and an additional pin (C). Note that the washers (G)

are not used with the lock plate.

MANUAL LIFT MODELS

NOTE: These instructions apply to Conquest / 1700 /

2700 Series tractors or Broadmoor / 1600 / 2600 Series

tractors equipped with a lift lever kit.

1. Install the lift link as shown in the upper frame of

Figure 6.

NOTE: The lift link on early model units had a hole locat-

ed in front of the slot, rather than behind. These early

model lift links must be removed and replaced with the

one contained in this kit (Ref. No. 22, Figure 1). The lift

link included with this kit (pictured above) is universal

and works in all applications.

Snowthrower

& Dozer

Applications

Mower

Applications

Installation Instructions Sub-Frame Hitch

Figure 7. Install Hitch

A. J-Hooks D. Hook

B. Hitch Rod E. Clamp Plate

C. Hitch Rod

Install Hitch

1. Slide the hitch under the tractor.

2. Raise the rear of the hitch and place the hook (C)

over the lift shaft.

3. Connect the front of the hitch to the tractor J-hooks

(A, Figure 7) using the hitch rod (B) and a safety clip

in the top holes of the push bar latch.

4. Secure the front of the hitch to the tractor by attach-

ing the hitch rod (C) and a safety clip in the bottom

holes of the push bar latch.

5. Push the clamp plate (D) backwards until it is snug

against the lift shaft. Tighten the clamp plate hard-

ware (E).

Sub-Frame Hitch Installation Instructions

Install Lift Rod

1. Slide the lift lever (A, Figure 8) onto the end of the

tractor lift shaft (B) under the right side footrest.

2. Use the tabs on the lift lever (A) to capture the tractor

lift arm. Secure in place with a clevis pin (D) and

safety clip (C).

Figure 8. Install Lift Lever

A. Lift Lever

B. Lift Shaft

C. Safety Clip

D. Clevis Pin

Figure 9. Install Lift Rod

A. Lift Lever

B. Lift Rod

C. Clip

3. Insert the rear of the lift rod (B, Figure 9) into the bot-

tom of the lift lever (A). Secure with a clip (C).

Perform lift rod adjustment according to the procedure

found in the attachment operator’s manual.

Installation Instructions Sub-Frame Hitch

REMOVAL

NOTE: After removing components, reinstall the clevis

pins and clips to prevent loss.

1. Disconnect the lift rod from the attachment and lift

lever (C, Figure 10).

2. Remove the clevis pin and clip from the lift lever (C)

and remove the lift lever.

3. Remove the front hitch rods (A) and (B). Remove the

hitch and hook (F).

4. Remove the lock plate (D, E) or switch the lift link

from dozer to mowing position (see page 7).

NORMAL INSTALLATION

1. Insert the hook (F, Figure 10) into the back of the

hitch. Mount the rear of the hitch on the lift cross-

shaft.

2. Secure the front of the hitch to the J-hooks using the

hitch rods (A) and (B) (Figure 7).

3. Install the downward pressure lock plate or switch the

lift link (see page 7).

4. Install the lift lever (C).

5. Install the lift rod and attachment (Figure 8).

Figure 10. Normal Installation & Removal

A. Hitch Rod

B. Hitch Rod

C. Lift Lever

D. Pressure Lock Plate

(Manual)

E. Pressure Lock Plate

(Hydraulic)

F. Hook

OBSOLETE

Sub-Frame Hitch Installation Instructions

FCD

Figure 12. Lift Link - Manual Lift Models

A. Pin

B. Rear Hole of Lift Bar (Snowthrower/Dozer

Applications)

C. Spacer

D. Hair Pin Clip

E. Upper Hole (Snowthrower/Dozer Applications)

F. Slot of Lift Link (Mower Applications)

G. Lower Hole (Mower Applications)

BCD

Snowthrower

& Dozer

Applications

Mower

Applications

Figure 11. Lift Lock Plate - Hydraulic Lift Models

A. Lift Cylinder

B. Flat Head Pin (Original)

C. Flat Head Pin (New)

D. Lock Plate

E. Hair Pin Clips

F. Lift Shaft Assy.

G. Washers

BCDF

LIFTVARIATIONSWHEN USING

ATTACHMENTS

When a front-mounted attachment such as a snowthrow-

er or dozer blade is used with the tractor, the lift mecha-

nism must be locked to provide downward force. When

the mower is reinstalled the downward pressure lock

must be released so that the mower can float.

Hydraulic Lift Models

When using a snowthrower or dozer, the downward

pressure lock plate (D, Figure 11) and an additional pin

ment. Note that the washers (G) are not used with the

lock plate.

When mowing, the downward pressure lock plate (D) is

removed and replaced with two washers (G). The addi-

tional pin (C) is also removed.

Fully lower the hydraulic lift. The lift assembly is spring

loaded so it will need to be held in the down position to

perform of the following procedures.

Manual Lift Models

NOTE: These instructions apply to Conquest / 1700 /

2700 Series tractors or Broadmoor / 1600 / 2600 Series

tractors equipped with a lift lever kit.

The lift link is installed differently depending on what

attachment is being used. Refer to Figure 12 for link

installation information.

Snowthrower

& Dozer

Applications

Mower

Applications

Installation Instructions Sub-Frame Hitch

Form No. 1733910-03

Rev. 12/2006

TP 200-4442-03-AT-SMAN

MANUFACTURING, INC.

500 N Spring Street / PO Box 997

Port Washington, WI 53074-0997 USA

Figure 4. Install Lock Plate - Manual Lift Models

A. Lift Shaft Assy. F. Lift Bar

B. Flat Head Pin (Original) G. Lock Plate

C. Flat Head Pin (New) H. Hair Pin Clips

D. Capscrew I. Spacer

E. Washer

DOWNWARD PRESSURE LOCK

PLATE - OBSOLETE

Note:The following information applies only

to models produced before October of 2002.

It is being included here for reference pur-

poses ONLY.

MANUAL LIFT MODELS

1. Rest the back of the lock plate (G, Figure 4) against

the spacer (I) and rotate until it lines up with the hole

in the lift bar (F).

2. Secure the lock plate (G) to the lift bar (F) using a flat

head pin (C) and hair pin clip (H).

Indice

Altri manuali Snapper Accessori per tosaerba

Snapper

Snapper 6-3041 Manuale utente

Snapper

Snapper 6-3131 Guida per l'amministratore

Snapper

Snapper 7600030 Guida all'installazione

Snapper

Snapper 1690195 Manuale utente

Snapper

Snapper 6-1410 Manuale utente

Snapper

Snapper 63305 Manuale utente

Snapper

Snapper YT18H Manuale operativo e di manutenzione

Snapper

Snapper 1600312 Manuale utente

Snapper

Snapper 447575 Guida per l'amministratore

Snapper

Snapper 5900703 Manuale utente

Snapper

Snapper 1694498 Manuale utente

Snapper

Snapper 7063375 Manuale utente

Snapper

Snapper 63307 Manuale utente

Snapper

Snapper PRO Manuale elenco delle parti

Snapper

Snapper BH500 Manuale utente

Snapper

Snapper 1600222 Manuale utente

Snapper

Snapper 63023 Manuale utente

Snapper

Snapper 1690044 Manuale utente

Snapper

Snapper 1687262 Manuale utente

Snapper

Snapper 6-1249 Manuale utente

Snapper

Snapper 1694955 Manuale utente

Snapper

Snapper 1694946 Manuale utente

Snapper

Snapper 6-3317 Manuale utente

Snapper

Snapper 6-0935 Manuale utente

Manuali Accessori per tosaerba popolari di altre marche

Ariens

Ariens 891008 Manuale utente

Rover

Rover 108 - 109 Manuale utente

Toro

Toro 112-5803 Manuale utente

Scag Power Equipment

Scag Power Equipment GC-F4 Manuale utente

RHINO

RHINO 800 Manuale utente

Exmark

Exmark Quest 126-7506 Manuale utente

Cub Cadet

Cub Cadet 19B70029100 Manuale utente

Stihl

Stihl AMK 043.1 Manuale utente

MTD

MTD 753-0873 Manuale

Toro

Toro 30810 Manuale utente

Bush Hog

Bush Hog RG60 Manuale utente

Land Pride

Land Pride RCF2760 Manuale utente

Simplicity

Simplicity 211 Manuale utente

Toro

Toro Z Master 116-0231 Manuale utente

Exmark

Exmark ULTRAVAC QUICK DUMP SYSTEM Manuale utente

Excel

Excel Two Bag Catcher Manuale utente

Textron

Textron Jacobsen Pro12 DFS Manuale utente

Toro

Toro 145-3495 Manuale utente