Softub T140 Manuale utente
ASSEMBLY INSTRUCTIONS
T140 / T220/ T300
www.softub.com
www.softub.com
Roll up your sleeves and set up the Softub! Do not use a razor knife to
open the box. Use the claw end of a hammer to tear the flaps open.
1
!
14ft
2x
1x
1x
1x
1x
1x
1x
1x
1x
2These are the items you received and will need.
Please note that the filter is probably already
installed in the tub. Please leave it installed on
the wall of the tub.
3
Place the straps for the cover on the ground in an “X” pattern. The back
side of the buckle should be facing up so the buckle attaches properly
on the lock. The plumbing connectors need to be between the straps.
!
Verify the placement of the straps under the tub. You can dry-fit the
cover at this point in time to make sure the straps are installed correctly.
Line up the connectors on the power unit with the connectors on the tub.
The power unit is not to be plugged in yet!
!
4
!
Twist the connectors on a clock-wise fashion until the connectors are
snug and no threads are showing. Connect the light connector.
!5
2-3 min.
6
Run the hose for 2 to 3 minutes in
the garden, yard or down a drain
before beginning to fill the tub. This
will help to clear out any algae or
debris that is in the hose. When
done, begin filling the tub.
!
2 In.
!
7
After filling the tub with about 2 inches
of water, smooth out any wrinkles on
the bottom of the liner by moving the
liner around with your hands and fingers.
Tucking the liner in the bottom edges
helps to alleviate the wrinkles.
!
approx. 2 In.
8
Make sure the filter is
installed if not installed
already. Soak filter in
warm water prior to
installing to ease the
installation. Fill tub to
a level 2 inches above
the highest jet.
DO NOT PLUG IN
THE TUB YET!
!
!
9
Check the tub connections
for leaks. Simply tighten the
connectors a little more if
there is a leak. Plug the tub
in now.
!
10
Check for leaks while the tub
is running. If there are leaks,
tighten the connectors. Now
install the foam and vinyl
connector covers.
!
!
15 min.
LIGHT
JETS
HEAT
FILTER
ON
LIGHT
JETS
HEAT
FILTER
OFF
With the tub running check the chemical levels and adjust them as necessary as advised in
the Water Care Guide. Open the air control on the control panel by rotating counter-clock-
wise for 15 minutes after adding the chemicals. After 15 minutes, close the air control by
rotating it counter-clockwise until it stops and put the lid on the tub.
!11
LIGHT
JETS
HEAT
FILTER
!
10
Set the tub to your desired
temperature and make sure
to lock your cover. Your tub is
now heating and will shut off
when the desired temperature
is reached. The tub heats at
1 to 1.5 degrees per hour.
!
www.softub.com
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Softub Vasca idromassaggio
Manuali Vasca idromassaggio popolari di altre marche
Bestway
Bestway Lay-Z-Spa 54189 Manuale utente
Jacuzzi
Jacuzzi ARGA ARG101C0110 Manuale elenco delle parti
Morphy Richards
Morphy Richards Essentials PC4006 Manuale utente
JNJ SPAS
JNJ SPAS SPA-318 Manuale di installazione
KIRAMI
KIRAMI Comfort Family Manuale utente
QCA Spa
QCA Spa VS501 PAK (VL260 TOPSIDE) Manuale utente
