SolarEdge SE3000US Manuale utente

Disclaimers

SolarEdge Installation Guide – MAN-01-00002-1.6

Disclaimers

Important Notice

No part of this document may be reproduced, stored in a retrieval system or transmitted, in

any form or by any means, electronic, mechanical, photographic, magnetic or otherwise,

without the prior written permission of SolarEdge Inc.

This document is solely for the use of SolarEdge customers and employees.

The material furnished in this document is believed to be accurate and reliable. However,

SolarEdge assumes no responsibility for the use of this material. SolarEdge reserves the

right to make changes to the material at any time and without notice. You may refer to the

SolarEdge web site (www.solaredge.com) for the most updated version.

All company and brand products and service names are trademarks or registered

trademarks of their respective holders.

Exclusion of Liability

The general terms and conditions of delivery of SolarEdge shall apply.

The content of these documents is continually reviewed and amended, where necessary.

However, discrepancies cannot be excluded. No guarantee is made for the completeness of

these documents.

Table of Contents

SolarEdge Installation Guide – MAN-01-00002-1.6

Table of Contents

Disclaimers....................................................................................................2

Handling and Safety Instructions................................................................6

Support and Contact Information...............................................................8

Chapter 1: Introducing the SolarEdge Power

Harvesting System..................................................................9

What is the SolarEdge Power Harvesting Solution? .................................9

SolarEdge Power Optimizer ....................................................................9

Single Phase Inverter.............................................................................10

SolarEdge Monitoring Portal................................................................. 11

Installation Workflow.................................................................................12

Transport and Storage...............................................................................13

Single Phase Inverter Transport.............................................................13

Single Phase Inverter Storage................................................................13

Equipment List............................................................................................ 13

Chapter 2: Installing the Power Optimizers......................15

Applicable Notes and Warnings................................................................ 15

Step 1, Mounting the Power Optimizers...................................................18

Step 2, Connecting Each PV Module to a Power Optimizer.....................20

OP250-LV, OP300-MV and OP400-MV.............................................. 20

PB250-AOB and PB350-AOB .............................................................. 21

Connecting Power Optimizers............................................................... 22

Step 3, Connecting Power Optimizers in Strings.....................................23

Verifying Proper Power Optimizer Connection ....................................24

Step 4, Recording Installation Information.............................................. 26

Chapter 3: Installing the Inverter.......................................27

Identifying the Inverter..............................................................................27

Selecting the Mounting Location...............................................................27

Chassis Clearance..................................................................................27

Mounting the Inverter................................................................................28

Connecting the Inverter .............................................................................31

Inverter Connection Overview ..............................................................31

AC Grids Supported .............................................................................. 34

Connecting the Single Phase Inverter....................................................35

Table of Contents

SolarEdge Installation Guide – MAN-01-00002-1.6

Completing the Single Phase Inverter Installation................................. 41

Installing the AC/DC Safety Switch...................................................... 42

Ground Fault Circuit Interrupter.............................................................55

Chapter 4: Commissioning the Installation.......................56

Commissioning – Workflow....................................................................... 56

Step 1, Activating the System................................................................ 57

Step 2, Pairing Power Optimizers to the Inverter .................................. 58

Step 3, Verifying Proper Operation ........................................................60

Step 4, Reporting and Monitoring Installation Data.............................. 61

Chapter 5: Replacing and Adding System Components ..64

Modifying an Existing Installation............................................................64

Chapter 6: Setting Up Communication..............................66

Communication Dataflow .......................................................................... 66

Connector Panel..........................................................................................66

Communication Types................................................................................67

Creating an RS232 (UART) Connection................................................... 69

Creating an Ethernet (LAN) Connection..................................................70

Creating an RS485 Bus Connection..........................................................75

Verifying the Connection ...........................................................................81

Troubleshooting Communication..........................................................82

Chapter 7: Inverter User Interface.....................................83

Inverter LCD Panel and LEDs..................................................................83

Inverter LCD Panel and User Buttons................................................... 84

Configuring the Inverter Using the LCD Panel and User Buttons.........88

Inverter Configuration Menu Options ................................................... 95

LCD Button Menu Options ...................................................................98

Configuring the Inverter Using the SolarEdge Configuration Tool.......99

Appendix A: Errors and Troubleshooting.......................100

Appendix B: Technical Specifications..............................108

Single Phase Inverter................................................................................108

OP250-LV, OP300-MV and OP400-MV ....................................................111

PB250-AOB and PB350-AOB..................................................................113

Table of Contents

SolarEdge Installation Guide – MAN-01-00002-1.6

Appendix C: Power Optimizer Mechanical

Specifications.......................................................................115

OP250-LV, OP300-MV, OP400-MV Power Optimizers .......................116

PB250-AOB and PB350-AOB Power Optimizers.................................. 117

Appendix D: Inverters Power De-rating..........................118

Appendix E: Limited Product Warranty.........................119

Handling and Safety Instructions

SolarEdge Installation Guide – MAN-01-00002-1.6

Handling and Safety Instructions

During installation, testing and inspection adherence to the following handling

and safety instructions is mandatory.

Safety Symbols

The following safety symbols are used throughout this document. Familiarize

yourself with the symbols and their meaning before installing or operating this

instrument.

WARNING!

Denotes a hazard. It calls attention to a procedure that, if not correctly perf

ormed

or adhered to, could result in

injury or loss of life. Do not proceed beyond a

warning note until the indicated conditions are fully understood and met.

Dénote un risque: il attire l'attention sur une opération qui, si elle n'est pas faite ou

suivi c

orrectement, pourrait causer des blessures ou un danger de mort. Ne pas

dépasser une telle note avant que les conditions requises soient totallement

comprises et accomplies.

CAUTION:

Denotes a hazard. It calls attention to a procedure that, if not corre

ctly performed

or adhered to, could result in

damage or destruction of the instrument. Do not

proceed beyond a caution sign until the indicated conditions are fully understood

and met.

Dénote un risque: il attire l'attention sur une opération qui, si elle

n'est pas faite ou

suivi correctement, pourrait causer un dommage ou destruction de l'équipement.

Ne pas dépasser une telle note avant que les conditions requises soient

totallement comprises et accomplies.

NOTE:

Denotes additional information about

the current subject.

IMPORTANT SAFETY FEA

TURE:

Denotes information about safety issues.

Handling and Safety Instructions

SolarEdge Installation Guide – MAN-01-00002-1.6

Instructions

WARNING!

The cover must only be opened after shutting off the AC

DC switch located below

the inverter and waiting five minutes. This removes both DC

and AC voltage from

the inverter

Do not remove the inverter cover before five minutes have elapsed after

disconnecting all sources of power. Only use lockable connectors for DC input.

Otherwise, there is a risk of electric shock form energy stored in the

capacitor.

Ne pas ouvrir le couvercle de l'onduleur avant d'avoir coupé l'interrupteur CA/CC

situé en dessous de l'onduleur et que cinq minutes ne se soient ecoulées. Cela

supprime les tensions CC et CA de l'onduleur.

Ne pas ouvrir le couvercle de l'ondul

eur avant que cinq minutes ne se soient

ecoulées après coupure de toutes les sources de puissance. Sinon, il y a un

risque de choc électrique provenant de l'énergie stockée dans le capaciteur.

WARNING!

Before operating the Single Phase Inverter, ensure

that the system has been

grounded properly.

Avant d'utiliser l'onduleur monophasé, assurez

-vous que le système est

correctement mis à la terre.

WARNING!

No user

-serviceable parts inside. This unit must be opened only by qualified

service personnel.

Repairs or testing under power must only be performed by

qualified

service personnel who are familiar with and qualified to work with this

Single Phase Inverter.

Ne contient aucune pièce réparable par l'utilisateur. L’unité ne doit être ouverte

que par un

technicien qualifié dans le cadre de l'installation et de la maintenance

Les réparations ou les tests électriques sous tension ne doivent être effectués

que par des techniciens qualifiés de SolarEdge, possèdant les connaissances et

les qualifications nécessaires pour travailler avec cet onduleur monophasé.

WARNING!

The supplied AC/DC

Safety Switch meets all requirements for a code-compliant

installat

ion of this ungrounded system. The DC section opens both the positive

and negative conductors.

Le sectionneur CA/CC externe (inclus) repond aux exigences de conformité pour

l’installation de ce système non

-relié à la terre. Le coupeur CC ouvre les

conducteurs positif et négatif.

Support and Contact Information

SolarEdge Installation Guide – MAN-01-00002-1.6

WARNING!

This unit must be connected only to a dedicated

AC branch circuit with a

maximum

Overcurrent Protection Device (OCPD) of 40 A.

Cet appareil doit être connecté uniquement à un circuit de dérivation dédié avec

un coéfficient TPOC (

dispositif de protection contre les surintensités) maximal de

40 A.

Support and Contact

Information

If you have technical problems concerning our products, please contact us:

USA and Canada:1877 360 5292

Germany: 089-45459730 and 089-4161703-39

France: 0800917410

Italy: 800 784 824

United Kingdom: 08002061058

Israel: 073 2403118

Australia: 1800149229

Rest of World: +1 (650) 319-8843

Fax: +972 73 240-3117

Email to:

support@solaredge.com (US and Canada)

support@solaredge.com (all other countries)

Before contact, please gather the following information:

Inverter and power optimizer type.

Serial number of the inverter and the power optimizer in question.

The error indicated on the inverter screen or on the SolarEdge Monitoring

Portal.

System configuration information, including the type and number of modules

connected and the number and length of strings.

The communication method to the SolarEdge server.

The Support option on the top right of the SolarEdge Configuration Tool’s

main window can be used to automatically collect all relevant information to be

sent to SolarEdge Professional Services for support. This option is described in

detail in the SolarEdge Configuration Tool Software Guide.

Introducing the SolarEdge Power Harvesting System

SolarEdge Installation Guide – MAN-01-00002-1.6

Chapter 1

Int

roducing the SolarEdge Power

Harvesting System

What is the SolarEdge Power

Harvesting Solution?

The SolarEdge power harvesting solution maximizes the power output from any

type of solar PV installation while reducing the average cost per watt. The

sections below describe each of the system’s components.

SolarEdge Power Optimizer

SolarEdge power optimizers can be connected to existing PV modules in order to

maximize power harvesting by locally performing Maximum Power Point

Tracking (MPPT) at the PV module level.

The power optimizers keep the string voltage fixed, regardless of the length of the

string and of the environmental conditions. Each SolarEdge power optimizer

directly transmits performance data from every PV module over the power line.

Three types of power optimizers are provided by SolarEdge, as follows:

Module add-on solutions, connected during installation to one or more PV

module. P/N: OP250-LV, OP300-MV, OP400-MV, OP480-IV, PB250-AOB

and PB350-AOB.

Module Embedded Solution (CSI), is supplied embedded into a PV

module.

Introducing the SolarEdge Power Harvesting System

SolarEdge Installation Guide – MAN-01-00002-1.6

You may refer to the SolarEdge power optimizer datasheets in order to determine

which power optimizer is most suitable for you requirements.

Figure 1: Add-On Box Solution

Single Phase Inverter

The Single Phase Inverter efficiently converts DC power received from the PV

modules into AC power that can be fed into the main circuit board of the site and

from there to the grid. The inverter also receives the monitoring data from each

power optimizer and transmits it to a central server (called the Monitoring Server)

through an Ethernet network to an external modem connection.

Figure 2: Single Phase Inverter

Mounting Hole

Top

Front

Bottom

Heat Sink Fins

LCD

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali SolarEdge Invertitore

SolarEdge

SolarEdge Power Harvesting System Manuale utente

SolarEdge

SolarEdge 330kW Manuale utente

SolarEdge

SolarEdge SE50K Manuale utente

SolarEdge

SolarEdge SE8000H-AU Manuale utente

SolarEdge

SolarEdge SE K Series Manuale utente

SolarEdge

SolarEdge storedge Manuale utente

SolarEdge

SolarEdge SE8K-N4 Manuale utente

SolarEdge

SolarEdge SE3000H-US Manuale utente

SolarEdge

SolarEdge SE330K Manuale utente

SolarEdge

SolarEdge P300 Manuale utente

SolarEdge

SolarEdge SE15K-AU Manuale utente

SolarEdge

SolarEdge Energy Bank Manuale utente

SolarEdge

SolarEdge UL1741-SA Manuale utente

SolarEdge

SolarEdge SE12.5k Manuale utente

SolarEdge

SolarEdge SE3K Manuale utente

SolarEdge

SolarEdge Power Optimizer Manuale utente

SolarEdge

SolarEdge StorEdge SE5K-RWS Manuale utente

SolarEdge

SolarEdge SE K Series Manuale utente

SolarEdge

SolarEdge SE2200H Manuale utente

SolarEdge

SolarEdge SE3000H-US Manuale utente

SolarEdge

SolarEdge StorEdge SE5000-xxS0 series Manuale utente

SolarEdge

SolarEdge EV Series Manuale utente

SolarEdge

SolarEdge SE15K Manuale utente

SolarEdge

SolarEdge SE5000H-US Manuale utente

Manuali Invertitore popolari di altre marche

Fourgroup

Fourgroup Easy Manuale utente

Velleman

Velleman PI300M Manuale utente

Sungrow

Sungrow SG350HX-US Manuale utente

WilTec

WilTec 61897 Manuale utente

SMA

SMA SUNNY BOY STORAGE 2.5 Manuale utente

Simplicity

Simplicity LANDLORD 316 Manuale utente

Santak

Santak SMAX 3000 Manuale utente

ATON

ATON RA.Store-3 Manuale utente

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Manuale utente

Tektronix

Tektronix CFG250 Manuale utente

Champion

Champion 200989 Manuale utente

Vanner

Vanner 20-500 Series Manuale utente

GE GEP Manuale utente

Astrel Group

Astrel Group Power Reducer Guida rapida

MULTIQUIP

MULTIQUIP GDP-5H Guida

GoWISE

GoWISE PS1007 Manuale utente

Promate

Promate PM13500D ES Manuale utente

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Manuale utente