Solatube Ubiflex flashing Manuale utente
Installation Instructions
Solatube Ø 35 cm round
pitched roof Ubiflex flashing
2
Contents
Contents
1. Product Overview........................................................................................................................... 4
1.1 Parts............................................................................................................................................ 4
2. Installation Steps ........................................................................................................................... 5
2.1 Step 1 Roof flashing............................................................................................................ 5
2.2 Step 2 Install the Ubiflex roof flashing............................................................................ 5
2.2.2 Step 2.2.2 High-Tack sealant.......................................................................................... 6
2.2.3 Step 2.2.3 Attach roof flashing tile clips..................................................................... 7
2.3 Step 3 Adjust top tube angle (if required)...................................................................... 7
2.4 Step 4 Install the top tube assembly............................................................................... 8
2.5 Step 5 Install LightTracker flex......................................................................................... 9
2.6 Step 6 Install RayBenders flex.......................................................................................... 9
2.7 Step 7 Fit the roof dome................................................................................................... 10
2.8 Step 8 Attach the brush seal........................................................................................... 10
2.9 Step 9 Install the bottom tube assembly...................................................................... 11
2.10 Step 10 Fit the Natural Effect Lens.............................................................................. 12
Version
20-08-2020
Safety Information
Always observe the safety instructions for the materials and tools to be used.
Always wear the appropriate personal protective equipment (gloves, safety goggles etc.)
We would suggest that any roof works is completed by an experienced roofer.
Always have any electrical works carried out by a certified electrician.
Please note that the installation works is carried out at your own risk.
3
Guarantee and disclaimer
Guarantee
Non-electrical Solatube®
manufacturing defects. Please retain the original proof of purchase to validate the product warranty.
Any costs associated to the installation of any replacement parts covered under the warranty remain
at the expense of the purchaser. Our terms and conditions are available upon request.
Disclaimer
Techcomlight Limited expressly disclaims any liability for any unexpected additional expense arising
as a result of condensation or any water damage resulting from condensation, installation not in
the control of Techcomlight Limited. Techcomlight cannot be held liable for damage to structures
caused as a result of making openings and installing Solatube®systems. Techcomlight assumes no
responsibility or obligation for the failure of an architect, contractor, installer or building owner to
comply with all applicable laws, ordinances, building codes, energy codes, fire and safety codes and
requirements, and adequate safety measures.
Installation instructions reserved. No rights can be derived from this publication.
4
Product overview
1. Product Overview
1
4
2
4
1.1 Parts
1. Flex roof dome
2. Top tube assembly
3. Bottom tube assembly
4. 5 x roof dome screws
5. Brush seal
6. High-tack sealant
7. LightTracker flex
8. 2 x Raybenders flex
9. Natural Effect Lens
10. Ubiflex pitched roof flashing
11. 3 x roof tile clips
12. Roll of aluminium tape
3
7
4
8
4
9
4
4
4
5
6
4
10
4
11
4
12
4
5
Installation Steps
2. Installation Steps
2.1 Step 1 Roof flashing
Determine where you want to install the Solatube from the inside and mark the position
through the ceiling and the roof.
Create a circular opening with a diameter of between Ø 370 - Ø 380 mm through both the
ceiling and roof construction.
2.2 Step 2 Install the Ubiflex roof flashing
Remove sufficient tiles from the roof to allow the flashing to fit down onto the tile battens as
shown below.
Determine the ideal position so that the flashing can be installed beneath the tiles above / to
the sides and down onto the tiles below.
Once the final position is determined, mark and cut any obstructing tile batten to allow the
top tube assembly to fit through the flashing down into the roof void.
Important: Temporarily insert the top tube assembly down through the flashing to help you
to centralise the flashing over the roof aperture created.
1
2
Mark the position and make a circular opening
Opening size between Ø 370 - Ø 380 mm
6
Installation Steps
Tip: The bottom skirt of the Ubiflex flashing is longer than the top.
Fix the Ubiflex roof flashing in place by screwing the top of the flashing to the tile battens.
Create a weather stop by folding the sides and top of the flashing upwards by a few
centimetres.
Dress the bottom skirt of the flashing down onto the profile of the tiles below.
2.2.2 Step 2.2.2 High-Tack sealant
Secure the lower skirt of the flashing down onto the tiles below with the High-tack adhesive /
sealant and tile clips provided.
Tip: Ensure that the tiles below the flashing skirt are free from dust and debris prior to
applying the High-tack adhesive / sealant.
Fit the roof tiles back around the sides and top of the roof flashing.
Note: The sides of the flashing must be overlapped by the roof tiles.
7
Installation Steps
2.2.3 Step 2.2.3 Attach roof flashing tile clips
The three tile clips provided are also used to secure the bottom skirt of the flashing down
onto the roof. Clamp the short "leg" of the clips between two tiles beneath the edge of the
flashing and bend the long "leg" back over the edge of the flashing to clamp it in place.
2.3 Step 3 Adjust top tube angle (if required)
If required, the integral angle within the top tube assembly can be rotated to create an
angle from 0 to 30 degrees to compensate for the pitch of the roof.
How to adjust the integral angle: Carefully peel back the protective film inside the tube
from along the angle seam.
Grasp the top tube with two hands, just below the adjustable angle seam (diagonal).
Use your thumbs and index fingers to rotate the angle section as required.
Adjust the angle so that the top tube assembly aligns with the bottom tube assembly.
Once the angle is correctly set, carefully apply tape to the outside of the tube over the tube
seams and around the angle.
Now remove the transparent protective film from the inside of the top tube assembly.
1
2
8
Installation Steps
2.4 Step 4 Install the top tube assembly
Carefully insert the top tube assembly down through the roof flashing until the transparent
dome ring is correctly seated down onto the top lip of the flashing as shown below.
Fix the dome ring onto the roof flashing using the dome screws provided, screwed through
the four grey spacers from the outside in. The screws will pierce through the flashing and
the inside of the reflective tubing. Be careful not to overtighten the screws as this may cause
damage to the dome ring.
Now remove the transparent protective film from the inside of the top tube assembly.
1
2
9
Installation Steps
2.5 Step 5 Install LightTracker flex
Place the dome upside down on a soft clean surface. Fit the LightTracker flex (this is the
mirrored insert) with the reflective side facing inwards. Align the holes in the LightTracker
over the corresponding tabs inside the dome and slide the LightTracker flex downwards to
secure it in place.
Note: If the sunlight from the south is blocked, do not mount the LightTracker flex in the
dome!
2.6 Step 6 Install RayBenders flex
Fit the two RayBenders flex inserts (these are the transparent ribbed insert) onto the
remaining tabs inside the dome with the smooth sides facing inwards and the ribbed sides
against the dome. Align the holes in the RayBenders with the corresponding tabs inside the
dome and slide the RayBenders downwards to secure them in place.
10
Installation Steps
2.7 Step 7 Fit the roof dome
Snap the dome onto the dome ring using the 4 snap closures. Ensure that all four
connecting points are properly engaged.
Important: Fit the dome with the LightTracker flex on the north side (facing south).
Tip: If you want to remove the dome again, insert the end of a wide screwdriver into the
opening of the snap fasteners and pry it off one by one from below.
2.8 Step 8 Attach the brush seal
Stick the brush seal strip around the outside of the bottom tube assembly or uppermost
extension tube, just below the top of the tube as shown below. Using the entire sealing strip,
wrap the strip around the tube keeping the rings tightly together as shown.
Note: if additional extension tubes are being used this operation must be performed around
the top of the uppermost extension tube.
Once the angle is correctly set, carefully apply tape to the outside of the tube over the tube
seams and around the angle.
2
1
Indice
Manuali Apparecchio di illuminazione popolari di altre marche
Emos
Emos CLASSIC ZY1431T Manuale utente
Westinghouse
Westinghouse Outdoor Lighting Fixture Manuale utente
Hedler
Hedler C 12 silent Manuale utente
Blizzard Lighting
Blizzard Lighting Puck: CSI Manuale utente
Energetic Lighting
Energetic Lighting ELYSL-5004 Series Manuale utente
Lightmaxx
Lightmaxx Shaft 5R Manuale utente
Cooper Lighting
Cooper Lighting Halo L3232E Manuale utente
Stageline
Stageline ODW-2410RGBW Manuale utente
Light Sky
Light Sky Tornado Series Manuale utente
Lightolier
Lightolier Paralyte 2424 PLA2G9LS26U Manuale utente
Lightolier
Lightolier Lytespan 83ED17S Manuale utente
Lightolier
Lightolier Calculite CS8226 Manuale utente