Solos Wearables Solos Manuale utente
USER GUIDE
Android
2 CONTENTS
CONTENTS
3 UNIT SETUP
APPLICATION SETUP
13 RIDE & RUN
15 ACTIVITIES
16 PROFILE, STATS & SETTINGS
GROUP COMMUNICATION
22 VOICE CONTROL
25 NAVIGATION
26 GHOST MODE
27 TROUBLESHOOTING
Charge the unit by plugging the micro-USB cable into the USB slot
• The LED will flash green when the unit is charging
• The LED will be solid green when the unit is fully charged
• Your SOLOS unit will be charged regardless of whether or not it is powered on
when the USB cable is plugged in
Switch on the unit by briefly pressing the main power button
• The green LED will illuminate to indicate it has powered on
• Your SOLOS will also say “Hello” to confirm it has been powered on
Button Control
Connecting in-ear headphones
• Using the same USB slot, you can connect the in-ear headphones to your Solos unit
Double tap functionality
• During activity, double tap the right temple area of your Solos to activate (or deactivate)
microphones for group-chat communication
3 UNIT SETUP
SOLOS DEVICE
LED INDICATOR
USB SLOT
POWER On: Single press
O: Hold for >5 seconds
Advance HUD screens
Volume adjustment
Pause / Resume
Answer call / Hang up
IN WORKOUT
IN CALL
N/A
1. Adjust the vertical height of the display
so that it’s in a desirable position based on
your preference. A good starting point is
with the main hinge rotated completely
down, as shown in the darker image.
2. Adjust the secondary tilt of the display
so that you can see the full image. If the
display shows upside down or you can’t
see it then the tilt is incorrect. Often,
this can be fine tuned by adjusting the
spread of the nose bridge and moving
the unit up and down your nose until
you find the optimum position.
3. Adjust the left/right alignment by slid-
ing the optical module using the thumb
catch under the pod. Even if you can see
the image, it’s important to explore this
travel since the display contrast will im-
prove when positioned properly.
4 UNIT SETUP
FITTING THE DISPLAY & ADJUSTING THE NOSEPIECE
To adjust the display, follow these steps:
To adjust the nosepiece, follow these steps:
It’s important to fit SOLOS so that it’s comfortable and you can see all
of the display clearly.
To make the nosepiece narrower,
pinch the rubber nose pads from the
outer sides closer together.
To make the nosepiece wider, expand
the rubber nose pads outward.
This is the neutral position.
1. Remove the thin bar located above the
nosepiece using a Phillips head
screwdriver
2. Position your prescription insert where
the thin bar was and use the same screw
to fasten the insert to your Solos headset
5 UNIT SETUP
CHANGING AND PROTECTING THE LENS
To attach a prescription lens, follow these steps:
Using Protective Lens Sleeve
*Note: This protective sleeve is not meant to prevent
damage to the headset under extreme forces or abuse
• Un-Velcro the flap to open the sleeve
• Slip the headset into the sleeve and close the
flap over the front of the Solos lens
• It should fit over the Solos optics module
Swapping interchangeable lens
To remove a lens from the headset:
• Detach the sides from the headset frame then
• Twist the lens either counter-clockwise or
clockwise to detach from the nose frame
To insert a lens:
• Insert both sides of the lens
into their proper areas on the
headset frame
• Align the lens with the nose
frame, then snap into place
Note: You will need to get your custom prescription lenses cut at an
optician before using with Solos
6 APPLICATION SETUP
• The first time you use the app, the app will take you through setup
• Begin by signing in, or by creating a new account
• The app will advise you of the password requirements
SETUP: SIGN IN OR CREATE AN ACCOUNT
7 APPLICATION SETUP
SETUP: PROFILE
• Create your profile by importing from Facebook, or enter your details manually
8 APPLICATION SETUP
• Ensure Bluetooth is enabled (the system will prompt you) and that your
SOLOS unit is switched on
• The app will search for nearby SOLOS headsets
• Select your SOLOS headset to begin pairing. (One of the screens will display your
headset name)
• Accept the pairing request on both the phone and on the headset
(by pressing the main button)
• The app will confirm when the connection is made.
SETUP: CONNECT HEADSET
9 APPLICATION SETUP
• Select the sport you wish to configure first to use SOLOS
Note: You can always switch sport later and the system will take you
through setup for that sport.
SETUP: SELECT SPORT
10 APPLICATION SETUP
• The app will automatically search for nearby BLE or ANT+ sensors
• Click on your sensors to connect them
• Any connected sensors will automatically reconnect from this point
• Note: Your headset must be connected for the system to connect to
ANT+ sensors
• Some sensors broadcast over both ANT+ and BLE, you only need to
connect to one instance of the sensor
SETUP: CONNECT SENSORS
Altri manuali per Solos
1
Indice
Altri manuali Solos Wearables Occhiali intelligenti
