SOMFY 1811482 Manuale utente

mportant information - safety

General information

ead this installation guide and the safety instructions carefully

before installing this Somfy product. All the instructions given

must be followed closely and this guide must be stored in a

safe place throughout the service life of your product.

These instructions describe how to install and commission this

product.

Any installation or use outside the ﬁeld of application speciﬁed

by Somfy is forbidden.

This invalidates the warranty and discharges Somfy of all

liability, as does any failure to comply with the instructions

given herein.

Somfy cannot be held responsible for any changes in

standards which come into eﬀect a>er the publication of these

instructions.

General safety instructions

• This product is not designed to be used by persons (including

children) whose physical, sensory or mental capacity is

impaired, or persons with little experience or knowledge, unless

they are under supervision or have received instructions on

using this product by a person responsible for their safety.

• Do not let children play with this product.

• Do not immerse the product in liquid.

• Do not drop, drill or dismantle this equipment, as this will

invalidate the warranty.

• Do not expose this equipment to high temperatures or leave it

in direct sunlight.

ntroduction

Congratulations on your purchase of the new Somfy opening

sensor.

Connected to TaHoma or Connexoon, this sensor lets you know if

your door or window is properly closed, wherever you are.

The sensor will also warn you in the event of any intrusion.

If used with TaHoma, you can also make used of the advanced

functions. For example, if you have a heating system that is

compatible with TaHoma, if your sensor detects an open window,

you can set the system to switch your heating on in freeze-

protection mode to avoid high energy use.

Contents

* 3 pre-glued bases.

3 replacements.

Description Qty

Opening and impact sensor 1

C 123 battery 1

Adhesive strips 6*

C P

Description Description

1 Unit 4 Calibration button

2 Magnet 5 Programming button

3 Battery housing 6 Mode selector switch

C P

Fitting the battery

To open the unit, press on the grey section located on the side of

the opening and impact sensor unit to unclip the front of the case.

Insert the battery the correct way ("+" side on the "+" side and "-"

side on the "-" side).

Do not replace the front of the case before adding the

opening and impact sensor to the TaHoma system and

conﬁguring it.

Adding to TaHoma / Connexoon system

TaHoma

On the TaHoma interface, select the tab.

- Select the Conﬁguration tab.

- Select the "IO" tab, then select "Add".

- Follow the procedure shown on the screen.

- AFTE ﬁnishing the pairing, the green indicator light will

switch oﬀ.

Connexoon

To add the opening and impact sensor to a Connexoon Box, the

two devices need to be paired.

Press the P OG button on the opening and impact sensor

and hold for 2 seconds.

Press the P OG button on the Connexoon Box and hold for

0.5 seconds.

The opening and impact sensor has now been added to the

Connexoon Box.

Do not replace the front of the case before conﬁguring

the opening and impact sensor.

2 cm Max

nstallation

There are 2 options for installing your opening and impact sensor

depending on the conﬁguration of your door/window.

Unit on the moving part and the magnet on the

frame of the door or window.

This enables opening detection if you have a

TaHoma Box or a Connexoon Box, and opening and

impact detection if you have a TaHoma Box with

the TaHoma security extension.

Installing the opposite way round from method A,

depending on the conﬁguration on your door/

window.

This enables opening detection if you have a

TaHoma Box or a Connexoon Box.

In the case of a type A or B installation,

the two parts (unit and magnet) must be in

alignment, with a maximum space of 3cm

between the two elements.

If, during installation, you ﬁnd

there is vertical oﬀset between

the unit and the magnet, this

should not exceed 2cm.

Mounting

Easy installation using adhesive strips

• Clean the surface where the unit and the magnet will be

mounted.

• Aﬃx the elements following the chosen installation method

(A or B).

Mounting with screws

• Press on the upper section of the

unit and magnet to unclip the front

panel.

• Place the back panel (of the unit or

magnet) into the chosen position and

the screw holes with a pencil.

• Use ﬁxing screws (3mm diameter

and 19mm in length) and suitable

plugs (3mm diameter and 25mm in

length) to ﬁx the opening and impact

sensor to the surface.

• Firmly secure the back section

of the opening and impact sensor

in place.

Conﬁguration

To use the opening and impact sensor in the various settings

previously mentioned, use the following conﬁgurations.

C P

Activation / Deactivation of magnet

The mode selector indicates the activation/deactivation of

the magnet.

• Opening detection

Used to detect intrusions into your home.

In the case of a type A or B installation, set the

mode selector to the "Magnet activated" position

(default position).

Close the cover.

The opening and impact sensor is now operational.

• Opening and impact detection

For detecting intrusion attempts and intrusions into your home.

Set the mode selector to the “Magnet activated”

position (default position), the proceed to the

impact “learning” mode (see p22).

This step enables the unit to recognise intrusion attempts.

C P C P

Magnet activated

(Default position)

Magnet deactivated

C P

Opening and impact "learning" mode

This enables the opening and impact sensor to recognise:

- an intrusion attempt: impact "learning"

This is accomplished through the following 3 steps (closed

window):

1) Press the calibration button (C) and hold for 3 seconds.

2) The red indicator light will light up for 10 seconds: close the

unit cover whilst the light is on.

3) The red indicator light will blink rapidly: this is the learning

step.

- Impact "learning": force/shake the door/window to simulate

an intrusion attempt.

If there is an error, the red indicator light will blink twice

every ﬁve seconds.

Carry out an intrusion or intrusion attempt test once this

stage is ﬁnished to check that the opening and impact

sensor is functioning correctly.

C P

Resetting the opening and impact sensor

To delete the opening and impact sensor from the TaHoma,

unclip the front panel of the unit, and press the programming

button (P) for 10 seconds, the indicator light will switch on then

switch oﬀ.

To reset the opening and impact sensor settings, unclip the front

panel of the unit and press the calibration (C) button for

10 seconds, the indicator lighting will switch on then switch oﬀ.

Somfy hereby declares that this product is in

compliance with the requirements of Directive

2014/53/EU. The full text of the Declaration of

Conformity is available at www.somfy.com/ce.

Recycling

Do not dispose of this product with the household

waste. Please take it to a collection point or an

approved centre to ensure it is recycled correctly.

Ensure batteries are separated from other types

of waste and are recycled via your local recycling

centre.

The images contained in this booklet are for illustrative

purposes only.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali SOMFY Accessori

SOMFY

SOMFY LIGHTING OUTDOOR RTS Manuale utente

SOMFY

SOMFY inteo Light sensor Manuale utente

SOMFY

SOMFY inteo EOLIS RTS Manuale utente

SOMFY

SOMFY EOLIS 3D Manuale utente

SOMFY

SOMFY animeo IB + Manuale utente

SOMFY

SOMFY Sunis WireFree II io Manuale utente

SOMFY

SOMFY animeo IB + Manuale utente

SOMFY

SOMFY SMART PLUG B-TYPE Manuale utente

SOMFY

SOMFY Sunea Guida

SOMFY

SOMFY Eolis 3D WireFree 1816081 Manuale utente

SOMFY

SOMFY 2401220 Manuale utente

SOMFY

SOMFY Sunis WireFree RTS Light Sensor Manuale utente

SOMFY

SOMFY EOLIS WIREFREE RTS Manuale utente

SOMFY

SOMFY Thermosunis Indoor Wirefree RTS Manuale utente

SOMFY

SOMFY Sunis WireFree Manuale utente

SOMFY

SOMFY animeo Manuale utente

SOMFY

SOMFY inteo EOLIS Manuale utente

SOMFY

SOMFY EOLIS RECEIVER Manuale utente

SOMFY

SOMFY EOLIS WIREFREE IO Manuale utente

SOMFY

SOMFY Freeroll RTS OSE Manuale utente

SOMFY

SOMFY Soliris io Manuale utente

SOMFY

SOMFY 5059202A Manuale utente

SOMFY

SOMFY 2401219 Manuale utente

SOMFY

SOMFY Animeo IB+ Manuale utente

Manuali Accessori popolari di altre marche

Hillco

Hillco 2810 Manuale utente

Siemens

Siemens QSA2700D Manuale dell'operatore

Contours

Contours ZY024 Manuale utente

Saivod

Saivod VS621 Manuale utente

Virtuox

Virtuox VirtuCLEAN 2.0 Manuale utente

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuale utente

Z-Wave

Z-Wave HSD-200Z Manuale utente

turck

turck FMX-IM-2UPLI63FX Manuale utente

Decagon Devices

Decagon Devices 10HS Manuale utente

UPPAbaby

UPPAbaby Cup Holder Manuale utente

Elko

Elko SmartSensor Leakage Wireless Manuale utente

Grizzly

Grizzly H8371 Manuale utente

Panasonic

Panasonic HG-T Series Manuale utente

IFM Electronic

IFM Electronic Efector 250 Series Guida di riferimento

DigiDesign

DigiDesign 888/24 I/O Manuale utente

PROZIS

PROZIS QUAY Manuale utente

patagonia

patagonia PSI Vest Manuale utente

SFC Energy

SFC Energy EFOY GO! Manuale utente